Bosch Appliances D9412GV3 9.4.3Installation, 9.4.4Setting the OctoPOPIT Switches, Off-BoardPoints

D9412GV3/D7412GV3 Operation and Installation Guide 9.0 Off-Board Points

9.4.3Installation

For the most effective installation, use the following four-step process:

1.Set the OctoPOPIT switches. Refer to Section 9.4.4 Setting the OctoPOPIT Switches.

2.Physically mount the OctoPOPIT in the enclosure. Refer to Section 9.4.5 Mounting OctoPOPITs, page 45.

3.Wire the OctoPOPIT. Refer to Section 9.4.6 Wiring OctoPOPITs on page 45.

4.Wire the OctoPOPIT sensor loops. Refer to Section 9.4.7 OctoPOPIT Sensor Loops on page 49.

9.4.4Setting the OctoPOPIT Switches

The D8128D OctoPOPIT has two sets of DIP switches (Figure 19 on page 43). Use the DIP switches on the top of the unit (with the terminal strip along the left edge) to set the address for the OctoPOPIT. Use the DIP switches at the bottom of the unit to enable or disable individual points connected to the OctoPOPIT.

Address Switches

The switches on the D8128D OctoPOPIT set point assignments and line termination. These switches are easier to set before mounting the D8128D in the enclosure.

Switches 1, 2, 3, and 4 assign the OctoPOPIT sensor loops to point numbers on the control panel. Table 14 shows the OctoPOPIT switch settings for point assignments.

Switch 5 sets line termination. Refer to Table 15.

Table 14: D8128D OctoPOPIT Switch Settings for D9412GV3 and D7412GV3

ZONEX 1	D8128D Address Switches					ZONEX 2
Points 9 to						Points 129
127	1	2	3	4	5	to 247
9 to 16	ON	ON	ON	ON	*	129 to 136
17 to 24	ON	ON	ON	OFF	*	137 to 144
25 to 32	ON	ON	OFF	ON	*	145 to 152
33 to 40	ON	ON	OFF	OFF	*	153 to 160
41 to 48	ON	OFF	ON	ON	*	161 to 168
49 to 56	ON	OFF	ON	OFF	*	169 to 176
57 to 64	ON	OFF	OFF	ON	*	177 to 184
65 to 72	ON	OFF	OFF	OFF	*	185 to 192
73 to 80	OFF	ON	ON	ON	*	193 to 200
81 to 88	OFF	ON	ON	OFF	*	201 to 208
89 to 96	OFF	ON	OFF	ON	*	209 to 216
97 to 104	OFF	ON	OFF	OFF	*	217 to 224
105 to 112	OFF	OFF	ON	ON	*	225 to 232
113 to 120	OFF	OFF	ON	OFF	*	233 to 240
121 to 127	OFF	OFF	OFF	ON	*	241 to 247

*Line Termination Switch

For the D8128D OctoPOPITs assigned to Points 121 to 127, 241, and 247, set Point Input Switch 8 to the OPEN position.

D9412GV3 uses Points 9 to 127 on Zonex 1 and Points 129 to 247 on Zonex 2.

D7412GV3 uses Points 9 to 75 on Zonex 1 only.

Table 15: Switch 5 Settings for Line

Termination

Is a D8125 POPEX	Switch 5 Setting(s) on
Module connected?	D8128D OctoPOPIT(s)
No	Set Switch 5 of only one
	D8128D to ON
Yes	Set Switch 5 of all
	D8128Ds to OFF

Point DIP Switches

Each point connected to the D8128D is enabled by closing the respective DIP switch, or disabled by opening the DIP switch. For example, to disable a device connected to the P3 Terminal (Point 3), move DIP switch number 3 to the OPEN position.

Bosch Security Systems, Inc. 10/10 F01U143070-03 44