Manuals / Bosch Appliances / Household Appliance / Home Security System

Bosch Appliances D7412GV3, D9412GV3 4.4Installing the Control Panel, 4.5Connecting Earth Ground

Models: D9412GV3 D7412GV3

1 76

Download 76 pages 25.33 Kb

Page 15

Figure 2: Enclosure Mounting

D9412GV3/D7412GV3 Operation and Installation Guide	4.0	Installation

Figure 2: Enclosure Mounting

1	2	3	2	4
			2	4

				3
			5
		6

7

8

9

1 -	Point chart label	6-	Enclosure mounting holes (5)
2 - Mounting skirt hooks (2)		7 -	Mounting skirt hook holes (2)
3 - Module mounting holes (12)		8 -	Back of D9412GV3/D7412GV3 Control Panel
4 - Tamper switch mounting holes (5)		9 -	Lock down tab
5 -	Skirt mounting hole (1)

4.4Installing the Control Panel

1.Place the control panel over the inside back of the enclosure, aligning the large rectangular openings of the mounting skirt with the mounting hooks of the enclosure. Slide the control panel down so that it hangs on the hooks. Refer to Figure 2, Item 2 on page 15.

2.Remove the tape from the #6 x 1/4-in. screw in the mounting tab on the control panel. The screw passes through the mounting tab and into the skirt mounting hole in the enclosure. Tighten the screw to secure the control panel in the enclosure.

3.Connect earth ground to the control panel before making any other connections. Refer to Section 4.5 Connecting Earth Ground.

4.5Connecting Earth Ground

4.5.1Terminal 10

To help prevent damage from electrostatic charges or other transient electrical surges, connect the system to earth ground at Terminal 10 before making other connections. Recommended earth ground references are a grounding rod or a cold water pipe.

Caution: Do not use telephone or electrical ground for the earth ground connection. Use

1.8mm (14 AWG) to 1.5 mm (16 AWG) wire when making the connection.

Do not connect other control panel terminals to earth ground.

4.5.2Ground Fault Detect Enable

To meet UL 864 requirements, enable

Ground Fault Detect.

A ground fault is a circuit impedance to earth ground. The control panel has a ground fault detection circuit that, when enabled, detects ground faults on Terminals 1 to 9 and 11 to 32. The control panel also detects and annunciates ground faults on any device connected to it.

Bosch Security Systems, Inc. 10/10 F01U143070-03

15

Image 15

Bosch Appliances D7412GV3 4.4Installing the Control Panel, 4.5Connecting Earth Ground, Enclosure Mounting, 4.5.1Terminal

Contents

Control Panels D9412GV3/D7412GV3Federal Communications Commission FCC Rules TrademarksCertifications and Approvals Listings and ApprovalsService Center in USA FCC Registration NumberRinger Equivalence: 0.0B Contents 13.0 Programmer and Accessory Connections Appendix A: System Wiring Diagrams, Issue AAppendix B: Point Address Charts Figures Tables1.0 Introduction IntroductionTable 1: Related Documentation Lightning Strikes 2.2Precautions during Installation2.0 Lightning Strikes 2.1EffectsOverview 3.1Configuration and PartsFigure 1: System Configuration 3.0Overview3.1.2Parts Available by Separate Order 3.1.1Parts ListAssembly Literature Pack3.2Accessories Table 3: Compatible Accessories1Overview 3.3.3Telephone Line Sniff 3.3Features in the D9412GV3 and D7412GV33.3.1SDI Molex Connector 3.3.2Tip and Ring Posts3.3.7Keypads 3.3.8Keyswitch3.3.9Access Control 3.3.12 Ground Fault Detection3.3.13 Ground Fault Detection Added Feature 4.0Installation4.1Installation Preparation InstallationFigure 2: Enclosure Mounting 4.4Installing the Control Panel4.5Connecting Earth Ground 4.5.2Ground Fault Detect EnableTable 5: Ground Fault Impedance Specifications 4.5.3Enabling Ground Fault DetectionFigure 3: Enabling Ground Fault Detection 4.5.4Ground Fault Specifications4.6.3Installing Modules and Relays 4.6Completing the Installation4.6.1Charging the Battery 4.6.2Installing and Wiring Detection DevicesService Walk Test Procedure 4.8Installing the Point Chart Label4.9Testing the System 4.10Service Walk Testb.Press the ESC key. VIEW UNTESTED ? appears Installation246 PTS TO TEST InstallationFigure 5 D9412GV3 Service Walk Test Flow Chart SERVICE WALK?73 PTS TO TEST Figure 6: D7412GV3 Service Walk Test Flow Chart75 PTS TO TEST 74 PTS TO TESTPower Supply 5.0Power Supply5.1Primary Power Terminals 1 and 5.2Secondary Power TerminalsFigure 7: Battery Terminals Figure 8: Non-Power-LimitedWiringPower Supply Investigate Low Battery reports immediately: If Replacing the BatteryCharging and Battery LEDs D8132 Boost Battery Backup: Adding a D8132Power Supply 5.2.6Battery Discharge and Recharge ScheduleTable 6: Battery Discharge and Recharge Schedule Charging Status and Low Battery LEDs6.1Circuit Protection 6.0Power Outputs6.2Total Available Power Power Outputs6.4.1Programming 6.4Programmable Power Output Terminals 6, 7, and6.4.3Fire System Power Formula Verification and Reset Relay7.2Notification Figure 10: RJ31X Wiring7.0Telephone Connections 7.1Registration7.8Telephone Line Monitor 7.5Phone LED Red7.6Operation Monitor LED Green 7.7Dialing Format7.11.2 Operation 7.11D928 Dual Phone Line SwitcherFigure 12: D928 Dual Phone Line Switcher 7.11.1 Description8.0On-BoardPoints 7.11.3Installing the D928 MountingWiring AC Power LEDOn-BoardPoints Figure 13: On-boardPoint Sensor Loop Wiring8.3Point Parameters Point ParametersOn-BoardPoints 8.4Point Response TimeOn-BoardPoints On-BoardPoints Off-BoardPoints 9.0Off-BoardPoints9.1Point Zonex Bus D9412GV3 Terminals and D7412GV3 TerminalsOff-BoardPoints Table 12 Off-BoardPoint Errors9.2D8125 and D9127 POPIT Modules ListingsOff-BoardPoints For system supervision, do not use looped wire terminals. Break the wire run to provide supervision of the connectionsOff-BoardPoints For system supervision, do not use looped wire terminals. Break the wire run to provide supervision of the connectionsTable 13: Data Expansion Loop Wire Specifications 9.3 Installing the D8125 POPEX Module9.3.2Wiring the D8125 to the Control Panel 9.3.3Wiring POPITs to the Data Expansion Loop9.3.7Program Record Sheet 9.3.4Wiring Data Expansion Loops to POPEX Modules9.3.5POPIT Sensor Loops 9.3.6POPIT Module Point Assignments9.4.1Description 9.4D8128D OctoPOPIT ModuleFigure 18: Program Record Sheet 9.3.8POPIT LabelsOff-BoardPoints 9.4.2ListingsRequirements for Fire Initiation Applications Figure 19 D8128D OctoPOPIT LayoutTable 15: Switch 5 Settings for Line Termination 9.4.3Installation9.4.4Setting the OctoPOPIT Switches Address SwitchesTable 16: Terminal Strip Connections 9.4.6Wiring OctoPOPITsUsing the Terminal Strip 9.4.5Mounting OctoPOPITsOff-BoardPoints For system supervision, do not use looped wire terminals. Break the wire run to provide supervision of the connectionsOff-BoardPoints For system supervision, do not use looped wire terminals. Break the wire run to provide supervision of the connectionsOff-BoardPoints Using Molex ConnectorsOff-BoardPoints 9.5Testing Off-BoardPoints9.4.7OctoPOPIT Sensor Loops Figure 23: D8128D OctoPOPIT Sensor Loops10.0Off-BoardRelays 10.1D8129 OctoRelayFigure 24: D8129 Connections to the D9412GV3 Figure 25 D8129 Connections to the D7412GV3 10.1.1 Configuring the D8129 OctoRelayTable 17: D8129 OctoRelay Switch Settings 10.1.3 InstallationTable 18: Number of D8128Ds Used with D8129s 10.1.4 Wiring Connections10.2.2 Installation 10.2D811 Arm Status Relay ModuleFigure 26: D811 Module Wiring to the D9412GV3 10.2.3 Wiring ConnectionsFigure 27: D811 Module Wiring to the D7412GV3 11.2Keypad Terminals 29 to Table 19: Keypad Address Settings11.0Arming Devices 11.1DescriptionTable 20: Keypad Connections 11.2.2 InstallationWire Limits for Individual Devices Extra Power for More Keypads11.3D279A Independent Zone Control 11.4KeyswitchFigure 28: Power at Keypads 11.4.3 InstallationFigure 29: Keyswitch Wiring Momentary ContactSilencing the Bell 12.0SDI Devices 12.2Installation12.3.1 Switch Settings Table 22: Printer Address Switch Settings12.4D9210B Wiegand Control Interface Module 12.4.1 Access12.4.2 Switch Settings Connecting the D9133DC12.5.4 Supervision 12.5.3 Address SettingsFigure 30: DX4020 DIP Switch Settings 12.5.2 Network Interface Modules13.3Programmer Access Reports 13.0Programmer and Accessory Connections13.1Programmer Connector 13.2Installer Keypad and Local Programmers ModeFigure 32: Programmer and Accessory Connections 13.4Accessory Connector14.0Faceplates 14.1D9412GV3 FaceplateFigure 33: D9412GV3 Faceplate Figure 34: D7412GV3 Faceplate 14.2D7412GV3 FaceplateA.1 D9412GV3 Control Panel Appendix A: System Wiring Diagrams, Issue AUse zero retard except for waterflow devices D9412GV3All external connections except Terminal 5 battery position are power limited A.2 D7412GV3 Control Panel D7412GV3 Figure 40: D7412GV3, SDI Devices System Wiring Zonex 1, Points 9 to 75 D7412GV3 Appendix B: Point Address ChartsZonex 1 Point Address Chart B.1 Zonex 1, Points 9 to 127 D9412GV3Zonex 2, Points 129 to 247 D9412GV3 Only Zonex 2 Point Address ChartTable 26: Specifications SpecificationsPage Bosch Security Systems, Inc 130 Perinton Parkway Fairport, NY USABosch Security Systems, Inc.,