15.Changing special functions using the memory switches
■Memory switches 10 - 1F
Switch
Motion when set to ON
The optional emergency stop switch can be used. | ||
— | ||
|
| |
Solenoid wiper can be used (available as an option). | ||
|
| |
— | ||
|
| |
Needle cooler output is enabled. (Needle cooler is available by special order.) | ||
|
| |
Thread | ||
|
| |
Thread | ||
|
| |
Presser position errors are not detected. | ||
|
| |
Needle up stop position errors are not detected. | ||
|
| |
Presser can be moved up and down before the home position is detected. | ||
(Normally the presser cannot be moved up and down until after the home position has been | ||
| detected.) | |
|
| |
— | ||
|
| |
— | ||
|
| |
Errors can be reset using the EMERGENCY STOP switch. (EMERGENCY STOP switch is | ||
available as an option.) | ||
| ||
|
| |
Thread is not trimmed when an emergency stop occurs during sewing. (EMERGENCY STOP | ||
switch is available as an option.) | ||
| ||
|
|
■Memory switches 20 - 2F
Switch | Motion when set to ON | |
|
| |
Machine head from previous B430E series is used. (Only the operation panel and box are Mark | ||
II.) | ||
| ||
|
| |
During thread breakage detection, sensitivity is decreased from 8 to 14 stitches at the sewing | ||
start. (Sensitivity during sewing is three stitches.) | ||
| ||
|
| |
When DIP switch | ||
ignored. | ||
| ||
|
| |
— | ||
|
|
■Memory switches 30 - 4F
30 to 4F are set by entering two-digit values.
These values are incremented using the P2 switch, and decremented using the P4 switch.
Switch | Possible setting range | Units | Initial value | Explanation | |
|
|
|
|
| |
0 - 30 | mm | 7 | Limits the maximum area in the horizontal direction (X) | ||
(Limited to 6.4 mm when settings have been initialized.) | |||||
|
|
|
| ||
0 - 30 | mm | 7 | Limits the maximum area in the vertical direction (Y) | ||
(Limited to 6.4 mm when settings have been initialized.) | |||||
|
|
|
| ||
12 - 27 | x 100rpm | 25 | Changes the maximum sewing speed. | ||
|
|
|
|
| |
1 - 15 | x 7.5° | 10 | Changes the feed timing | ||
1 (Fast) ¨10 (Standard) Æ 15 (Slow) | |||||
|
|
|
| ||
0 - 5 | Needle | 1 | The sewing speed at the sewing start is 400 rpm for the | ||
specified number of stiches. | |||||
|
|
|
| ||
3 - 9 | x 100rpm | 4 | Changes the sewing start speed specified by | ||
|
|
|
|
| |
0 - 99 | x10ms | 0 | Timer for controlling timing during continuous operation | ||
|
|
|
|
| |
1 - 20 | x 7.5° | 10 | Changes the feed timing one stitch before the sewing end. | ||
1 (Fast) ¨10 (Standard)Æ 20 (Slow) | |||||
|
|
|
| ||
1 - 20 | x 7.5° | 10 | Changes the feed timing two stitches before the sewing | ||
end. | |||||
|
|
|
| ||
1 - 20 | x 7.5° | 1 | Changes the feed timing for the third stitch at the sewing start. | ||
1 (Fast) ¨10 (Standard) Æ 20 (Slow) | |||||
|
|
|
| ||
1 - 20 | x 7.5° | 1 | Changes the feed timing for the second stitch at the sewing start. | ||
|
|
|
|
| |
1 - 20 | x 7.5° | 1 | Changes the feed timing for the first stitch at the sewing start. | ||
|
|
|
|
| |
— | — | — | — | ||
|
|
|
|
| |
— | — | — | — | ||
|
|
|
|
| |
— | — | — | — | ||
|
|
|
|
| |
— | — | — | — | ||
|
|
|
|
| |
| — |
| — | ||
- | — | — | |||
|
|
|
| ||
|
|
|
|
|
64