16. Table of error codes
Code | Cause | Remedy | |
| Home position cannot be detected | Turn off the power and check the connection of home | |
(malfunction of home position sensor), or | |||
position sensor connector P1. | |||
| malfunction of power supply circuit board. | ||
|
| ||
|
|
| |
| You tried to change the program number | Press the RESET switch. | |
Set DIP switch | |||
when DIP switch | |||
| program number. | ||
|
| ||
|
|
| |
| Button attachment error | Remove the cause of the error at the robot. | |
●Button feeding error | ●Press the MANUAL switch on the button feeder to | ||
|
| feed the buttons. | |
| ●Button blockage | ●Refer to section | |
| ●Button feeder is in adjustment mode | ●Press the RESET switch to stop the buzzer from | |
|
| sounding. | |
|
| The error code display will not disappear until | |
|
| adjustment mode has been canceled. | |
Heat sink of control circuit board is | Turn off the power and clean the air intake port of the | ||
abnormally hot. | box. | ||
| |||
|
|
| |
| Malfunction of EEPROM (malfunction of main | Turn off the power, and turn it back on. If the error | |
continually occurs, contact a qualified service | |||
circuit board). | |||
| technician. | ||
|
| ||
| Corrupted EEPROM data, or main PROM | Press the RESET switch to reset the error. However, | |
| the data (memory switches, display and user | ||
version has been upgraded. | |||
programs) will be reset to the backup data or initialized. | |||
|
| ||
| Corrupted EEPROM control information data. | Press the RESET switch to reset the error. However, | |
the data (memory switches, display and user | |||
| |||
|
| programs) will all be initialized. | |
|
|
| |
| Solenoid | Turn off the power and contact a qualified service | |
circuit board), or power relay is not operating | |||
technician. | |||
(malfunction of power supply circuit board). | |||
| |||
|
| ||
Bad connection in cable between power | Turn off the power and check if connectors P16 is | ||
supply circuit board and main circuit board. | disconnected. | ||
| |||
Abnormal current detected in power supply | Turn off the power and contact a qualified service | ||
circuit board. | technician. | ||
| |||
|
|
|
■Errors generated when optional equipment is connected
Code |
| Cause | Remedy | |
|
|
| Turn the EMERGENCY STOP switch clockwise to | |
Emergency stop switch was pressed. | release the lock, and then press the RESET switch to | |||
|
|
| reset the error. | |
|
|
|
| |
|
|
| Turn the EMERGENCY STOP switch clockwise to | |
Emergency stop switch was pressed during | release the lock, and then press the RESET switch to | |||
sewing. |
| reset the error. You can then press the STEP BACK | ||
|
| |||
|
|
| switch to repeat the sewing. | |
|
|
| ||
| Emergency stop switch is being continually |
| ||
pressed, or emergency switch connection | Turn off the power and check. | |||
| error. |
|
| |
|
|
|
| |
|
|
| Turn the EMERGENCY STOP switch clockwise to | |
Thread breakage detected. | release the lock, and then press the RESET switch to | |||
reset the error. You can then press the STEP BACK | ||||
|
|
| ||
|
|
| switch to repeat the sewing. | |
|
|
|
|
REFERENCE | segment LED alphabet |
|
|
|
|
|
|
|
|
| |
| Panel display |
|
|
|
|
|
|
|
|
|
|
| Text display | A | b | c | d | E | F | 6 | H | L | o |
66 |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|