Emix, CA0X, Cac#, Cadx | Graco 332564B manual

					System Errors
System Errors

Code	Type	Description	Problem	Cause	Solution
EB00	Rec-	Stop Button	Record of a stop button	Indicates system stop	n/a
	ord	Pressed	press.	key on ADM was
				pressed.
EC00	Rec-	Setup	Record of changing	Indicates date and time	n/a
	ord	Value(s)	setup variables.	when setup values
		Changed		were changed.
EL00	Rec-	System	Record of power cycle	Indicates date and	n/a
	ord	Power On	(ON).	time when system was
				started.
EM00	Rec-	System	Record of power cycle	Indicates date and	n/a
	ord	Power Off	(OFF).	time when system was
				turned off.
EMIX	Advi-	Pump Off	The pumps are not	Pump power was	Start pumps by
	sory		powered and are	turned off or an error	pressing pump start
			unable to move.	occurred.	key on Advanced
					Display module.
ES00	Advi-	Factory	Record of defaults		n/a
	sory	Defaults	being loaded.

Communication Errors

NOTE: In some error codes listed below, a # symbol is shown as the last digit. This symbol represents the applicable component number, which can vary. The unit’s display will show the applicable number as the last digit in the code. For example, the CAC# code listed in this table will be displayed as CAC1 if the affected component is color change board 1, CAC2 for board 2, and so on.

Code	Type	Description	Problem	Cause	Solution
CA0X	Alarm	Comm. Error	System does not	This communication	Check CAN cable
		ADM	detect the Advanced	error indicates that	connecting ADM to
			Display Module	the Network has lost	the EFCM.
			(ADM).	communication with
				the Advanced Display
				Module.
CAC#	Alarm	Comm. Error	System does not	This communication	Check CAN cable
		Color Change	detect the Color	error indicates that	connections to
		#	Change Module #.	the network has lost	the Color Change
				communication with	Module # and any
				the Color Change	interconnected
				Module #.	modules.
CADX	Alarm	Comm. Error	System does not	This communication	Check CAN cables
		Fluid Module	see the Enhanced	error indicates that	connecting ADM to
			Fluid Control Module	the Network has lost	the EFCM. Replace
			(EFCM).	communication with	Cable or EFCM as
				the EFCM.	necessary.

332564B

95

Image 95

Graco 332564B System Errors Code Type Description Problem Cause Solution, Emix, CA0X, Cac#, Cadx

Contents

ProMix PD2K Proportioner for Automatic Spray Applications Important Safety Instructions Contents Manual No Related ManualsManual No Description 0359 ModelsECB Labels Model AC2000 High Pressure Identiﬁcation Label Fire and Explosion Hazard Intrinsic Safety Personal Protective Equipment Moisture Sensitivity of Isocyanates Important Isocyanate ISO InformationIsocyanate Conditions Keep Components a and B Separate General Information ADM Display USB Download ProcedureAdvanced Display Module ADM USB Upload Procedure ADM Keys and Indicators Function ADM Keys and Indicators Key Function Soft Key IconsSoft Key Functions Key Function Screen Icons Navigating the Screens Pre-Operation Tasks Pre-operation ChecklistPower On Valve Settings Initial System SetupFlush Before Using Equipment With Color Change Without Color Change Prime and Fill the System Operation Using Automatic Display Module ADM Spraying Flush Mixed Material Purging Color Change System ShutdownFlush the System Single Color System PD2K Discrete I/O Connections Operation Using a Programmable Logic Controller PLCNetwork Communications and Discrete I/O Discrete I/O Analog Inputs Digital Inputs KEY Discrete I/O Connections on Efcm CGM Kits Communication Gateway Module CGM DetailsCGM Overview ProMix PD2K Network Outputs Output Register 00 Current System ModeNumber Operation Mode Description Network Communication I/O Data Map Output Register 06 Actual Mix Ratio Output Registers 01, 02, 03, and 04 Pump StatusPump States for Output Registers Description Ber Output Register 05 Actual Mix Flow Output Register 12 Active Recipe Material B Flush Sequence Output Register 14 Active Recipe Potlife Timeout Set PointOutput Register 27 Safety Interlock Input Status Output Registers 28 36 DCS Command Structure Output Register 38 40 Software Version Output Register 37 Time Operation Using a Programmable Logic Controller PLC None Network Output Data Map Read Only PSI = ERR = Busy= ACK = NAK ProMix PD2K Network Inputs Input Register 00 System Mode Command Input Register 07 Go to Recipe Number Input Register 02 Flush/Prime Pump CommandInput Register 03 Mix Pump 1 Control Set Point Input Register 10 Gun 1 Trigger Input Register 08 Clear Active AlarmInput Registers 14 21 DCS Command Structure Input Register 09 Job Complete Operation Using a Programmable Logic Controller PLC Network Input Data Map Write/Read 40180 Gun 3 Trigger Uint32 Purge Mode Sequence Operation Flow Charts Inactive Pump Flush and Prime Sequences Flush Pump Command Change Color Change Sequence Standby Mix Ready? no Mixing Sequence Clear Active Alarm Alarm Clearing Sequence Dynamic Command Description Network Communication Dynamic Command Structure DCS DCS List of DCS CommandsDynamic Commands with Command ID Write User ID Write Recipe Write Flush Sequence Read User ID Write Fluid Control Mode Read Flush Sequence Read Recipe Read Fluid Control Mode Yymmdd Read Job Info Example Ascii Character String Decode Algorithm Read Alarm InfoYymmdddw Read Event Info Flow Control System Home Screen Run Mode ScreensOpening Screen See Advanced Screen 1, page 82, to set Home Screen Key Description Details Key Description Key Description Spray Screen Spray Screen, in Standby Mode Fill Screen, Color a Selected Fill Screen Usage Screen Usage Screen Events Screen Errors ScreenJobs Screen Password Screen Setup Mode Screens System Screen Mix Pressure Tolerance Mix Idle TimeoutMix No Flow Timeout Low Flow Timeout Hose Length and Diameter Gun Hose LengthGun Hose Diameter Mix At Wall Gateway ID Enable Manual Override Gun Trigger SignalFlow Control Setpoint Signal Fluid Control Recipe Screen Flush Screen Pump Screen Default Settings Not Selected Default Settings Selected Pump Screen 3, Pressure Monitoring Disabled Pressure Alarm and Deviation Limits Calibrate Screen Calibration Screens Volume Check Screen Enter Measured Volume of Solvent Maintenance Screen Maintenance Screens Maintenance Screen 4, Color Valve Resets Advanced Screen Download Depth Enable USB Downloads/UploadsLog 90% Full Advisory Enabled Display Units Perform the pressure check Calibration ChecksPump Pressure Check Pump Volume Check Scroll to Calibrate Screen 3, Solvent Meter Calibration Multiple Color Systems Color ChangeSingle Color Systems Gun Trigger Input Function System ErrorsTo Clear Error and Restart Mix Errors Code Type Description Problem Cause Solution Error CodesPurge Errors Code Type Description Problem Cause Solution Pumping Errors Code Type Description Problem Cause Solution EBH# Code Type Description Problem Cause Solution SAD1 Pressure Errors Code Type Description Problem Cause Solution Qbdx Qadx CAC# System Errors Code Type Description Problem Cause SolutionEmix CA0X Cddx CagxCDC# USB Errors Code Type Description Problem Cause Solution Wxuu WxudUSB B9SX B9AXB9BX ENT# Calibration Errors Code Type Name DescriptionEND# ENS0 Code Type Name Description Maintenance Errors Flushing MaintenancePreventive Maintenance Schedule Cleaning the ADM Positive Displacement Metric Proportioner Technical Data For Graco Canada Customers Graco Standard WarrantyGraco Information