Solvent Meter Calibration | Graco 332564B instruction

Calibration Checks

Solvent Meter Calibration

1.The meter and lines must be primed with solvent before doing the calibration. See Prime and Fill the System, page 20.

2.If the display is on a Run Mode screen, press

to access setup screens.

3.Scroll to Calibrate in the menu bar.

4.Scroll to Calibrate Screen 3, page 79.

5.Press the soft key to initiate the calibration.

NOTE: For maximum accuracy, use a gravimetric (mass) method to determine the actual volumes dispensed.

NOTE: Verify that the ﬂuid line is ﬁlled and at the proper pressure before calibrating. Air in the line or pressure that is too high may cause incorrect calibration values.

6.Trigger the gun into a graduated cylinder. Dispense a minimum of 500cc of material.

7.The volume that the unit measured displays on the screen.

8.Compare the amount on the screen to the amount in the graduated cylinder.

NOTE: If the value is substantially different, repeat the calibration process.

9.Enter the amount of solvent dispensed in the Measured Volume ﬁeld on the screen.

10.After the measured volume is entered, the controller calculates the new solvent meter K-factor and displays it on the screen. The standard meter K-factor is 0.021 cc/pulse.

11.Press to accept the calibration. Press to cancel the calibration and retain the previous K-factor.

86

332564B

Image 86

Graco 332564B important safety instructions Solvent Meter Calibration, Scroll to Calibrate Screen 3

Contents

Important Safety Instructions ProMix PD2K Proportioner for Automatic Spray Applications Contents Manual No Related ManualsManual No Description 0359 ModelsECB Labels Model AC2000 High Pressure Identiﬁcation Label Fire and Explosion Hazard Intrinsic Safety Personal Protective Equipment Keep Components a and B Separate Important Isocyanate ISO InformationIsocyanate Conditions Moisture Sensitivity of Isocyanates General Information ADM Display USB Download ProcedureAdvanced Display Module ADM USB Upload Procedure ADM Keys and Indicators ADM Keys and Indicators Function Key Function Soft Key IconsSoft Key Functions Key Function Navigating the Screens Screen Icons Pre-Operation Tasks Pre-operation ChecklistPower On Valve Settings Initial System SetupFlush Before Using Equipment Without Color Change With Color Change Operation Using Automatic Display Module ADM Prime and Fill the System Spraying Purging Flush Mixed Material Single Color System ShutdownFlush the System Color Change System Discrete I/O Operation Using a Programmable Logic Controller PLCNetwork Communications and Discrete I/O PD2K Discrete I/O Connections Digital Inputs Analog Inputs Discrete I/O Connections on Efcm KEY CGM Kits Communication Gateway Module CGM DetailsCGM Overview Network Communication I/O Data Map Output Register 00 Current System ModeNumber Operation Mode Description ProMix PD2K Network Outputs Output Register 05 Actual Mix Flow Output Registers 01, 02, 03, and 04 Pump StatusPump States for Output Registers Description Ber Output Register 06 Actual Mix Ratio Output Registers 28 36 DCS Command Structure Output Register 14 Active Recipe Potlife Timeout Set PointOutput Register 27 Safety Interlock Input Status Output Register 12 Active Recipe Material B Flush Sequence Output Register 37 Time Output Register 38 40 Software Version Operation Using a Programmable Logic Controller PLC Network Output Data Map Read Only None PSI = NAK = Busy= ACK = ERR Input Register 00 System Mode Command ProMix PD2K Network Inputs Input Register 07 Go to Recipe Number Input Register 02 Flush/Prime Pump CommandInput Register 03 Mix Pump 1 Control Set Point Input Register 09 Job Complete Input Register 08 Clear Active AlarmInput Registers 14 21 DCS Command Structure Input Register 10 Gun 1 Trigger Operation Using a Programmable Logic Controller PLC Network Input Data Map Write/Read 40180 Gun 3 Trigger Uint32 Operation Flow Charts Purge Mode Sequence Flush Pump Command Inactive Pump Flush and Prime Sequences Color Change Sequence Change Mixing Sequence Standby Mix Ready? no Alarm Clearing Sequence Clear Active Alarm Network Communication Dynamic Command Structure DCS Dynamic Command Description Write User ID List of DCS CommandsDynamic Commands with Command ID DCS Write Recipe Write Flush Sequence Write Fluid Control Mode Read User ID Read Recipe Read Flush Sequence Read Fluid Control Mode Read Job Info Yymmdd Example Ascii Character String Decode Algorithm Read Alarm InfoYymmdddw Read Event Info Flow Control System Home Screen Run Mode ScreensOpening Screen Home Screen Key Description Details See Advanced Screen 1, page 82, to set Key Description Key Description Spray Screen, in Standby Mode Spray Screen Fill Screen Fill Screen, Color a Selected Usage Screen Usage Screen Events Screen Errors ScreenJobs Screen Setup Mode Screens Password Screen System Screen Low Flow Timeout Mix Idle TimeoutMix No Flow Timeout Mix Pressure Tolerance Mix At Wall Gun Hose LengthGun Hose Diameter Hose Length and Diameter Enable Gateway ID Fluid Control Gun Trigger SignalFlow Control Setpoint Signal Manual Override Recipe Screen Flush Screen Pump Screen Default Settings Selected Default Settings Not Selected Pressure Alarm and Deviation Limits Pump Screen 3, Pressure Monitoring Disabled Calibration Screens Calibrate Screen Volume Check Screen Enter Measured Volume of Solvent Maintenance Screens Maintenance Screen Maintenance Screen 4, Color Valve Resets Advanced Screen Display Units Enable USB Downloads/UploadsLog 90% Full Advisory Enabled Download Depth Perform the pressure check Calibration ChecksPump Pressure Check Pump Volume Check Solvent Meter Calibration Scroll to Calibrate Screen 3, Multiple Color Systems Color ChangeSingle Color Systems Gun Trigger Input Function System ErrorsTo Clear Error and Restart Mix Errors Code Type Description Problem Cause Solution Error CodesPurge Errors Code Type Description Problem Cause Solution Pumping Errors Code Type Description Problem Cause Solution Code Type Description Problem Cause Solution EBH# SAD1 Pressure Errors Code Type Description Problem Cause Solution Qadx Qbdx CA0X System Errors Code Type Description Problem Cause SolutionEmix CAC# Cddx CagxCDC# USB Errors Code Type Description Problem Cause Solution Wxuu WxudUSB B9SX B9AXB9BX ENS0 Calibration Errors Code Type Name DescriptionEND# ENT# Maintenance Errors Code Type Name Description Cleaning the ADM MaintenancePreventive Maintenance Schedule Flushing Technical Data Positive Displacement Metric Proportioner For Graco Canada Customers Graco Standard WarrantyGraco Information