Fluid Control, Manual Override, Gun Trigger Signal | Graco 332564B

Setup Mode Screens

System Screen 5

System screen 5 sets the following system operating parameters.

Figure 32 System Screen 5

Fluid Control

Select the desired operating mode (pressure or ﬂow), using the pull-down menu.

•In Pressure Mode, the motor will adjust the pump speed to maintain the ﬂuid pressure set by an external control device.

•In Flow Mode, the motor will maintain a constant speed to maintain the target ﬂow rate set by an external control device.

Manual Override

Check this box to give users system control at the ADM. Leave the box unchecked if all system settings

are controlled through a PC, PLC, or other networked device.

Gun Trigger Signal

Select the format of the signal indicating whether the spray device is triggered.

•Discrete — the signal is sent via a direct, hard-wired connection

•Network — the signal is sent via a PC, PLC, or other networked device.

Flow Control (Setpoint Signal)

Select the format of the signal that indicates system ﬂow rate or pressure.

•Discrete — the signal is sent via a direct, hard-wired connection. This selection will make the Max Rate ﬁeld active.

•Network — the signal is sent via a PC, PLC, or other networked device.

Stepup Gain and Stepdown Gain

These ﬁelds are active only for systems set to ﬂow control on System Screen 5. Enter a value from 1 to 100 to optimize system response time to a change in ﬂuid ﬂow setpoint. Use the Stepup Gain ﬁeld for increases in ﬂuid ﬂow setpoint. Use the Stepdown Gain ﬁeld for decreases in ﬂuid ﬂow setpoint.

332564B

71

Image 71

Graco 332564B Fluid Control, Manual Override, Gun Trigger Signal, Flow Control Setpoint Signal

Contents

ProMix PD2K Proportioner for Automatic Spray Applications Important Safety Instructions Contents Manual No Related ManualsManual No Description 0359 ModelsECB Labels Model AC2000 High Pressure Identiﬁcation Label Fire and Explosion Hazard Intrinsic Safety Personal Protective Equipment Moisture Sensitivity of Isocyanates Important Isocyanate ISO InformationIsocyanate Conditions Keep Components a and B Separate General Information ADM Display USB Download ProcedureAdvanced Display Module ADM USB Upload Procedure ADM Keys and Indicators Function ADM Keys and Indicators Key Function Soft Key IconsSoft Key Functions Key Function Screen Icons Navigating the Screens Pre-Operation Tasks Pre-operation ChecklistPower On Valve Settings Initial System SetupFlush Before Using Equipment With Color Change Without Color Change Prime and Fill the System Operation Using Automatic Display Module ADM Spraying Flush Mixed Material Purging Color Change System ShutdownFlush the System Single Color System PD2K Discrete I/O Connections Operation Using a Programmable Logic Controller PLCNetwork Communications and Discrete I/O Discrete I/O Analog Inputs Digital Inputs KEY Discrete I/O Connections on Efcm CGM Kits Communication Gateway Module CGM DetailsCGM Overview ProMix PD2K Network Outputs Output Register 00 Current System ModeNumber Operation Mode Description Network Communication I/O Data Map Output Register 06 Actual Mix Ratio Output Registers 01, 02, 03, and 04 Pump StatusPump States for Output Registers Description Ber Output Register 05 Actual Mix Flow Output Register 12 Active Recipe Material B Flush Sequence Output Register 14 Active Recipe Potlife Timeout Set PointOutput Register 27 Safety Interlock Input Status Output Registers 28 36 DCS Command Structure Output Register 38 40 Software Version Output Register 37 Time Operation Using a Programmable Logic Controller PLC None Network Output Data Map Read Only PSI = ERR = Busy= ACK = NAK ProMix PD2K Network Inputs Input Register 00 System Mode Command Input Register 07 Go to Recipe Number Input Register 02 Flush/Prime Pump CommandInput Register 03 Mix Pump 1 Control Set Point Input Register 10 Gun 1 Trigger Input Register 08 Clear Active AlarmInput Registers 14 21 DCS Command Structure Input Register 09 Job Complete Operation Using a Programmable Logic Controller PLC Network Input Data Map Write/Read 40180 Gun 3 Trigger Uint32 Purge Mode Sequence Operation Flow Charts Inactive Pump Flush and Prime Sequences Flush Pump Command Change Color Change Sequence Standby Mix Ready? no Mixing Sequence Clear Active Alarm Alarm Clearing Sequence Dynamic Command Description Network Communication Dynamic Command Structure DCS DCS List of DCS CommandsDynamic Commands with Command ID Write User ID Write Recipe Write Flush Sequence Read User ID Write Fluid Control Mode Read Flush Sequence Read Recipe Read Fluid Control Mode Yymmdd Read Job Info Example Ascii Character String Decode Algorithm Read Alarm InfoYymmdddw Read Event Info Flow Control System Home Screen Run Mode ScreensOpening Screen See Advanced Screen 1, page 82, to set Home Screen Key Description Details Key Description Key Description Spray Screen Spray Screen, in Standby Mode Fill Screen, Color a Selected Fill Screen Usage Screen Usage Screen Events Screen Errors ScreenJobs Screen Password Screen Setup Mode Screens System Screen Mix Pressure Tolerance Mix Idle TimeoutMix No Flow Timeout Low Flow Timeout Hose Length and Diameter Gun Hose LengthGun Hose Diameter Mix At Wall Gateway ID Enable Manual Override Gun Trigger SignalFlow Control Setpoint Signal Fluid Control Recipe Screen Flush Screen Pump Screen Default Settings Not Selected Default Settings Selected Pump Screen 3, Pressure Monitoring Disabled Pressure Alarm and Deviation Limits Calibrate Screen Calibration Screens Volume Check Screen Enter Measured Volume of Solvent Maintenance Screen Maintenance Screens Maintenance Screen 4, Color Valve Resets Advanced Screen Download Depth Enable USB Downloads/UploadsLog 90% Full Advisory Enabled Display Units Perform the pressure check Calibration ChecksPump Pressure Check Pump Volume Check Scroll to Calibrate Screen 3, Solvent Meter Calibration Multiple Color Systems Color ChangeSingle Color Systems Gun Trigger Input Function System ErrorsTo Clear Error and Restart Mix Errors Code Type Description Problem Cause Solution Error CodesPurge Errors Code Type Description Problem Cause Solution Pumping Errors Code Type Description Problem Cause Solution EBH# Code Type Description Problem Cause Solution SAD1 Pressure Errors Code Type Description Problem Cause Solution Qbdx Qadx CAC# System Errors Code Type Description Problem Cause SolutionEmix CA0X Cddx CagxCDC# USB Errors Code Type Description Problem Cause Solution Wxuu WxudUSB B9SX B9AXB9BX ENT# Calibration Errors Code Type Name DescriptionEND# ENS0 Code Type Name Description Maintenance Errors Flushing MaintenancePreventive Maintenance Schedule Cleaning the ADM Positive Displacement Metric Proportioner Technical Data For Graco Canada Customers Graco Standard WarrantyGraco Information