Manuals / Carrier / Household Appliance / Air Conditioner

Carrier 33CSPREMLK specifications

Models: 33CSPREMLK

1 44

Download 44 pages 4.58 Kb

Page 15

Manual background

15

NOTE: Remove all unused red wires from J4 connector to prevent 24 vac shorting other components or ground. Inputs on J4 are 24 vac. Red leads are voltage source.

Fig. 9 — PremierLink™ Controller Sensor Wiring — With Programmable or Non-Programmable Thermostat

Image 15

Carrier 33CSPREMLK specifications

Contents

Economizer with Johnson 4 to 20 mA CONTENTSSAFETY CONSIDERATIONS SAFETY NOTE GENERALINSTALLATION PremierLink Controller Hardware - The PremierMount PremierLink Control Fig. 1 - PremierLink Control Module PremierLink Controller Inputs and OutputsBoard TB PremierLink Connections40RM Connections 38AK, AKS, ARZ, ARS TerminalPremierLink Connections PremierLink Connections40RM Connections 38ARD Terminal Board TBPremierLink Connections PremierLink Connections40RM Connections 38AH Terminal Board TB2Control 40RMQ ConnectionsPremierLink Connections 38AQ007PremierLink Connections 40RMQ Connections38AQS012-016 Terminal Board TB2 Table 2 - Color Code Recommendations Typical Wiring 33ZCT55SPT Table 3 - Thermistor Resistance vs TemperatureOutdoor Air Temperature Sensor Fig. 3 - Space Temperature SensorFig. 5 - T58 Communicating Sensor Typical Wiring 33ZCT58SPTFig. 6 - Space Temperature Averaging LEGEND OAT - Outdoor Air Temperature Sensor SAT - Supply Air Temperature SensorSPT - Space Temperature Sensor 33ZCT55CO2, 33ZCT56CO2 Page Page P/N HH79NZ017 Fig. 14 - Outdoor Air Temperature SensorSupply Air Temperature SAT Sensor Fig. 13 - Outdoor Air Quality Sensor CoverFig. 16 - Outdoor Air Temperature Sensor Installation - Located in Building WallTable 4 - Recommended Cables Fig. 18 - Enthalpy Switch/Receiver Dimensions 33CSENTHSW Fig. 19 - Enthalpy Sensor Dimensions33CSENTSEN Connect the 4-20mA In terminal on the enthalpy switch/ receiver to the 4-20mA Out terminal on the return air enthalpy sensor. Connect the 24-36VDC Out terminal on the enthalpy switch/receiver to the 24-36VDC In terminal on the return air enthalpy sensor. See Fig Fig. 21 - Differential Enthalpy Control Wiring Sensor and Mounting Plate 33AMKITENT006 Fig. 22 - Differential Enthalpy ControlPage Fig. 28 - Position of Actuator Mode Switches Fig. 26 - PremierLink Control Wiring toFig. 27 - PremierLink Control Wiring to Table 5 - Actuator Drive Direction SettingsJohnson Actuator With Wire Harness M9206-GGC-2 Fig. 29 - PremierLink Controller Wiring toPerform System Check-Out START-UPSETP OATL NTLO UHDB SAT 54.2 F SUPPLY AIR TEMPERATUREFig. 31 - Navigator Module in Display Mode PremierLink Navigator By CarrierNTLO UNOCC. OAT LOCKOUT TEMP CONFIGURATIONEnter Password 1111 default password SETP OATL NTLO UHDBTable 7 - Points Display Heating Stage 2 Display Units Table 9 - Alarm Service Configuration Table 8 - Thermostat Control Input DisplayTable 10 - Controller Identification Table 12 - Occupancy Configuration Table 11 - Holiday ConfigurationTable 13 - Set Point Configuration Table 14 - Service Configuration Selection Submaster Center DX Cooling Table 15 - PremierLink Control Configuration Global Schedule Low Reference Units Table 16 - Occupancy Maintenance Pre-occupancy Table 17 - Maintenance Page Copyright 2002 Carrier Corporation