Manuals / Carrier / Household Appliance / Air Conditioner

Carrier Air Conditioner specifications C. Unit Start-Up cont, OPTIONS2 Options Configuration, CL-5

Models: Air Conditioner

1 96

Download 96 pages 57.36 Kb

Page 93

CUT ALONG DOTTED LINECUT ALONG DOTTED LINE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

C.Unit Start-Up (cont)

PRESS ESCAPE KEY TO DISPLAY ‘OPT1’. PRESS DOWN ARROW KEY TO DISPLAY ‘OPT2’. PRESS ENTER KEY.

RECORD CONFIGURATION INFORMATION BELOW:

OPTIONS2 (Options Configuration)

ITEM	DESCRIPTION		STATUS	UNITS	VALUE
CTRL	Control Method	0 = Switch
		1	= 7 day sched.
		2	= Occupancy
		3	= CCN
CCNA	CCN Address	1 to 239
CCNB	CCN Bus Number	0 to 239
BAUD	CCN Baud Rate	1 = 240
		2	= 480
		3	= 9600
		4	= 19,200
		5	= 38,400
LOAD	Loading Sequence Select	1 = Equal loading
		2	= Staged loading
LLCS	Lead/Lag Circuit Select	1 = Automatic
		2	= Circuit A leads
		3	= Circuit B leads
LCWT	High LCW Alert Limit	2 to 60		^F
DELY	Minutes off time	0 to 15		min.
ICE.M	Ice Mode Enable	Enable/Disable

PRESS ESCAPE KEY TO DISPLAY ‘OPT2’. PRESS DOWN ARROW KEY TO DISPLAY ‘RSET’. PRESS ENTER KEY.

RECORD CONFIGURATION INFORMATION BELOW:

RESETCON (Temperature Reset and Demand Limit)

ITEM	DESCRIPTION		STATUS	UNITS	VALUE
	COOLING RESET
CRST	Cooling Reset Type	0	= No Reset
		1	= 4-20 mA input
		2	= External temp-OAT
		3	= Return fluid
		4	= External temp-SPT
CRT1	No Cool Reset Temp	0 to 125		°F
CRT2	Full Cool Reset Temp	0 to 125		°F
DGRC	Degrees Cool Reset	–30 to 30		^F
HRST	Heating Reset Type	0	= No Reset
		1	= 4-20 mA input
		2	= External temp-OAT
		3	= Return fluid
		4	= External temp-SPT
HRT1	No Heat Reset Temp	Not Supported		°F
HRT2	Full Heat Reset Temp	Not Supported		°F
DGRH	Degrees Heat Reset	–30 to 30		^F
	DEMAND LIMIT
DMDC	Demand Limit Select	0 = None		0
		1	= External switch input
		2	= 4-20 ma input
		3	= Loadshed
DM20	Demand Limit at 20mA	0 to 100		%
SHNM	Loadshed Group Number	0 to 99
SHDL	Loadshed Demand Delta	0 to 60		%
SHTM	Maximum Loadshed Time	0 to 120		min
DLS1	Demand Limit Switch 1	0 to 100		%
DLS2	Demand Limit Switch 2	0 to 100		%
	LEAD/LAG
LLEN	Lead/Lag Chiller Enable	Enable/Disable
MSSL	Master/Slave Select	Slave/Master
SLVA	Slave Address	0 to 239
LLBL	Lead/Lag Balance Select	Enable/Disable
LLBD	Lead/Lag Balance Delta	40 to 400		hours
LLDY	Lag Start Delay	0 to 30		min

CL-5

Image 93

Carrier Air Conditioner C. Unit Start-Up cont, OPTIONS2 Options Configuration, RESETCON Temperature Reset and Demand Limit

Contents

Energy Management Module EMM Enable/Off/Remote Contact Switch Controls Start-Up, Operation, Service, and Troubleshootingwith ComfortLink Controls 50/60 HzConfiguring and Operating Dual Chiller CONTENTS contGENERAL INTRODUCTIONMAJOR SYSTEM COMPONENTS Control Module Communication Carrier Comfort Network CCN InterfaceTable 2 - Thermistor Designations Table 3 - Status Switches LEGEND FOR FIGTable 4 - Output Relay Page CCN LEN DATA COMMUNICATION PORT Fig. 2 - 24 V Control Schematic, Unit SizesCCN LEN DATA COMMUNICATION PORT Fig. 3 - 24 V Control Schematic, Unit Sizes 080-110, 230B-315BCCN LEN DATA COMMUNICATION PORT and Reset Button Locations Fig. 6 - Enable/Off/Remote Contact Switch, Emergency On/Off SwitchFig. 5 - Main Base Board CEPL130346-01OPERATING DATA AWG - American Wire Gage EXV - Electronic Wire Gage040-110 130-210 And associated modular units040-070 Fig. 8 - Thermistor T3 and T4 Locations080-110 AND ASSOCIATED MODULAR UNITS 130-210 AND ASSOCIATED MODULAR UNITSEXV - Electronic Expansion Valve Fig. 9 - Compressor Thermistor Locations T7 and T8Fig. 11 - Typical Space Temperature Sensor Wiring Fig. 13 - Compressor Protection Control System Module - Sizes Fig. 14 - Compressor Ground Fault Module SizesFig. 15 - Electronic Expansion Valve EXV Fig. 16 - Energy Management Module CEPL130351CEBD430351-0396-01C TESTTable 5A - Part Load Data Percent Displacement, Standard Units Table 5A - Part Load Data Percent Displacement, Standard Units cont Table 5A - Part Load Data Percent Displacement, Standard Units cont Page Page Page A1†A2,A3,B1†,B2 UNIT Table 6 - Required Hardware for Additional Unloaders Head Pressure Control PumpoutFig. 17 - Deadband Multiplier Fig. 18 - Condenser Fan Sequence Fig. 19 - Scrolling Marquee Display Service Test See Table 9 - Both main power andINSTALL DUAL CHILLER LEAVING FLUID THERMISTOR T9 HERE THERMISTOR WIRING LEAVING FLUIDFig. 20 - Dual Chiller Thermistor Location Table 7 - Marquee Display Menu StructureSUB-MODE Table 8 - Run Status Mode and Sub-Mode DirectoryKEYPAD RANGETable 9 - Service Test Mode and Sub-Mode Directory Table 11 - Pressure Mode and Sub-Mode Directory Table 10 - Temperature Mode and Sub-Mode DirectoryTable 12 - Set Point Mode and Sub-Mode Directory CIR.BTable 14 - Inputs Mode and Sub-Mode Directory Table 13 - Reading and Changing Chilled Fluid Set PointTable 15 - Outputs Mode and Sub-Mode Directory Table 16 - Configuration Mode and Sub-Mode DirectoryTable 16 - Configuration Mode and Sub-Mode Directory cont Table 16 - Configuration Mode and Sub-Mode Directory cont Table 17 - Example of Temperature Reset Return Fluid Configuration Table 16 - Configuration Mode and Sub-Mode Directory contTable 18A - Example of Configuring Dual Chiller Control Table 18B - Example of Configuring Dual Chiller Control Slave ChillerMaster Chiller Table 19 - Example of Compressor Lead/Lag Configuration Table 20 - Time Clock Mode and Sub-Mode DirectorySCHD Table 22 - Operating Mode and Sub-Mode Directory Table 21 - Setting an Occupied Time ScheduleMODE NO Table 23 - Operating ModesITEM EXPANSION DESCRIPTIONTable 25 - Example of Reading and Clearing Alarms Table 24 - Alarms Mode and Sub-Mode DirectoryFig. 21 - Standard Chilled Fluid Temperature Control - No Reset Alarms/alerts clear, YES changes to NODISPLAY Table 26 - Configuring Temperature ResetTable 27 - Menu Configuration of 4 to 20 mA Cooling Set Point Control Fig. 22 - Cooling Set Point 4 to 20 mAChange Accepted Table 28 - Configuring Demand Limit Fig. 23 - 4 to 20 mA Demand Limiting TROUBLESHOOTINGENTER and until the sub-menu item RCRN “RESET Table 29 - Alarm and Alert Codes ALARM Table 29 - Alarm and Alert Codes contT112 T113Table 29 - Alarm and Alert Codes cont CCN command forManual once con Table 29 - Alarm and Alert Codes cont SERVICE Electronic ComponentsTable 30 - Oil Charge Fig. 24 - Cooler Thermistor Locations Table 31 - Plugs Fig. 25 - Typical Tube Sheets, Cover Off Non-Removable TubesFig. 26 - Elliott Tube Plug SIZESFig. 27 - Cooler Head Bolt Tightening Sequence Typical Tube Sheet Condenser CoilsFig. 28A - Condenser Fan Adjustment Fig. 28B - Condenser Fan Adjustment 50 Hz Low Noise Fan Option UnitsStandard 50 and 60 Hz Units and 60 Hz Low Noise Fan Option Units Fig. 31 - Printed Circuit Board Connector Refrigerant Feed Components - Each circuit hasFig. 30 - Electronic Expansion Valve EXV Fig. 33 - Thermistor Connections to J5 and J8 Processor Boards Fig. 32 - Thermistors Temperature SensorsTable 32A - 5K Thermistor Temperature F vs Resistance/Voltage VOLTAGE DROP A FOR THERMISTORS T1, T2, T7-T9VOLTAGE DROP B FOR THERMISTORS T3-T6 Table 32B - 5K Thermistor Temperature C vs Resistance/Voltage cont VOLTAGE DROP A FOR THERMISTORS T1, T2, T7-T9VOLTAGE DROP B FOR THERMISTORS T3-T6 For Thermistor T10 Table 33A - 10K Thermistor Temperatures F vs Resistance/Voltage DropFor Thermistor T10 Table 33B - 10K Thermistor Temperatures C vs Resistance/Voltage DropFig. 34 - Cooler Heater Cables Table 34 - Pressure Switch Settings psig kPaPRE-START-UP System CheckFig. 35 - Compressor Connections Lead Compressor Shown Table 35 - Temperature Limits for Standard Units START-UP AND OPERATIONOperating Limitations FIELD WIRING Refrigerant CircuitTable 36 - Nominal and Minimum Cooler Fluid Flow Rates Control Wiring Fig. 36 - Accessory SensorFig. 37 - Control Wiring 24 Fig. 38 - Hot Gas Bypass Control Wiring 115SIGNAL Fig. 40 - Energy Management Module EMM WiringSIGNAL SIGNALCXB ACCESSORY Fig. 41 - Compressor Expansion Board CXB Accessory WiringCXB ACCESSORY BOARDUNIT Configuration Settings OPTIONS1 Options ConfigurationAPPENDIX A - CCN TABLES DISPLAY STDU SETUP CONFIGURATION SCREEN TYPE OPTIONS2 Options ConfigurationSCHEDOVR TIMED OVERRIDE SETUP ALARMDEF Alarm Definition TableRESETCON Temperature Reset and Demand Limit APPENDIX A - CCN TABLES contBRODEFS Broadcast POC Definition Table AUNIT General Unit Parameters APPENDIX A - CCN TABLES contCIRCAAN Circuit A Analog Parameters CIRCADIO Circuit A Discrete ParametersAPPENDIX A - CCN TABLES cont CIRCBAN Circuit B Analog ParametersCIRCBDIO Circuit B Discrete Parameters OPTIONS Unit Parameters APPENDIX A - CCN TABLES contALARMS APPENDIX A - CCN TABLES contSTRTHOUR CURRMODS APPENDIX A - CCN TABLES contSETPOINT LOADFACTOCCUPANCY MAINTENANCE TABLE WSM EQUIPMENT PART COOL SOURCE MAINTENANCE TABLESUPERVISOR MAINTENANCE TABLE CSM/FSM EQUIPMENT TABLE Type 621H, BlockAPPENDIX B - FLUID DROP PRESSURE CURVES Cooler Fluid Pressure Drop Curves - 30GUN,GUR040-110ENGLISH AND SI APPENDIX B - FLUID DROP PRESSURE CURVES cont Cooler Fluid Pressure Drop Curves - 30GUN,GUR130-210ENGLISH SI ENGLISH SI Cooler Fluid Pressure Drop Curves - 30GUN,GUR230A-255A, 270A/B-420A/B1 Module B - 30GUN,GUR270 2 Module A - 30GUN,GUR230-255 3 Module A - 30GUN,GUR270,330 Module B - 30GUN,GUR330,360 50 HzAPPENDIX B - FLUID DROP PRESSURE CURVES cont Cooler Fluid Pressure Drop Curves - 30GUN,GUR230B-315BENGLISH AND SI APPENDIX B - FLUID DROP PRESSURE CURVES cont Cooler Fluid Pressure Drop Curves - 30GTN,GTR040-110ENGLISH AND SI APPENDIX B - FLUID DROP PRESSURE CURVES cont Cooler Fluid Pressure Drop Curves - 30GTN,GTR130-210ENGLISH SI ENGLISH SI 1 Module B - 30GTN,GTR270 2 Module A - 30GTN,GTR230-2553 Module A - 30GTN,GTR270,330 Module B - 30GTN,GTR330,360 50 Hz ENGLISH AND SI APPENDIX B - FLUID DROP PRESSURE CURVES contCALL FOR FREE CATALOG SERVICE TRAININGRemove and use for job file A. Preliminary Information START-UP CHECKLIST FOR COMFORTLINK CHILLER SYSTEMSEQUIPMENT Chiller MODEL NO COMPRESSORSCL-2 B. Preliminary Equipment Check Check box if completeC. UnitStart-Up cont SYSTEM FLUID VOLUME IN LOOP TYPE SYSTEMCHECK PRESSURE DROP ACROSS COOLER COOLER LOOP FREEZE PROTECTION IF REQUIREDOPTIONS1 Options Configuration UNIT Configuration SettingsC. Unit Start-Up cont CL-4RESETCON Temperature Reset and Demand Limit OPTIONS2 Options ConfigurationC. Unit Start-Up cont CL-5SLCT Heating Cooling Setpoint Select C. Unit Start-Up contSETPOINT CL-6CL-7 C. Unit Start-Up contAll Units