P460 Rack mounting procedure | Casio specs

Chapter 3 Avaya P460 Chassis and Module Installation

P460 Rack mounting procedure:

1 Position the brackets as shown in Figure 3.4

Figure 3.4 Positioning the rack-mounting brackets

b

a

3

3

a

b

Key

aFront-mount position

bMid-mount position

2Firmly fix the brackets to the chassis with the screws provided. Use five screws for each bracket.

3Position the switch in the rack.

4Fasten the switch in the rack with the screws provided. The screw size is 8-32x¼

Caution: Do not place other equipment on top of the P460

Avaya P460 Installation and Maintenance Guide

9

Image 23

Casio manual P460 Rack mounting procedure, Positioning the rack-mounting brackets

Contents

Avaya P460 Page Contents Table of Contents Radius Ieee Ietf List of Tables List of Tables Avaya P460 Installation and Maintenance Guide List of Figures Page Power Supplies Before you Install the Avaya P460Safety Information Conventions Used in the Documentation FCC Notice CLI Conventions WarrantyAvaya Support Preface Avaya P460 Installation and Maintenance Guide Introduction Avaya P460 Overview Management and Monitoring Avaya P460 Key FeaturesHigh Availability Flexibility Operating Safety Avaya P460 Chassis and Module Installation Environmental Prerequisites Required Tools AC Power Requirements Key Chassis Component Location Rack Mounting Installing the P460 on a Table Top 140 mm Positioning the rack-mounting brackets P460 Rack mounting procedure Installing the Cable Guide Cable Guide Installation PSU Power Supply Unit Installation Avaya P460 Switch Fan Module Location Fan Module Replacement or Installation Installing the Avaya P460 Fan Module Location of the Avaya P460 Supervisor Modules Supervisor Module Installation Installing the P460 Supervisor Module 10 Lcoation of Avaya P460 I/O Modules Module Installation 11 I/O Module Component Location Module Installation Procedure 12 Installing P460 I/O Modules Turning on the Avaya P460 Installing a PSU Turning on a Chassis with no Modules Powering UpInserting an Additional PSU Turning on a Chassis with a Supervisor Module Only If there are two PSUs Removing or Switching off a PSUIf there is one PSU If there are three PSUs Power Management Process Power Management I/O Module Power Management Process M460ML-SPV LEDs Avaya P460 PanelsM460ML-SPV Panel PWR ACT LED and OPR LED Summary Function LEDs Starting Point After Power-up or Reset LNK LAG RS-232 Port Sideband Connection M460ML-SPV Supervisor Module PortsM460ML-SPV Left and Right Pushbuttons Eth Port Outband Connection P460 Supervisor Module ASB Pushbutton M460ML-SPV ASB Alternate Software Bank Pushbutton Power Supply Panel Page M460ML-SPV Supervisor Module Modes Maximizing Avaya P460 AvailabilityM460ML-SPV Supervisor Module Redundancy Synchronizing the Supervisor Modules Manually Following screen capture shows the process Configuration File Synchronization Maximizing Avaya P460 Availability P460 show environment power Redundant Power Supplies Sample Power Budget Calculation Calculating the Power Budget Establishing a Console Connection with the P460 Establishing Switch Access Inband Interface Connection CLI Commands Establishing a Telnet Connection with the Switch Inband M460ML-SPV Supervisor Module Fast Ethernet Console Port Establishing a Telnet Connection with the Switch Outband Outband Interface Connection CLI Commands Redundant Outband Connections Redundant Outband Connections Overview Sideband PPP Interface CLI Commands Set interface ppp ipaddrnet-mask Setting Up Sideband PPP Connection ConfigurationPage Avaya Msnm P460 Manager Welcome Running the Avaya Msnm P460 Manager P460 Device Manager Install from your Local Web Site Installing the Java Plug-inInstalling from the P460 Documentation and Utilities CD Install from the Avaya Web Site Documentation Page Local User Accounts User AuthenticationAccess Levels Local User Account CLI Commands Introduction to Radius Radius Radius CLI Commands Illustrates the Radius authentication procedure User Authentication Allowed Managers Allowed Manager CLI Commands Default System Parameters Configuration Defaults Configuration Default CLI Commands Basic Switch Configuration Operating parameters System Parameter ConfigurationIdentifying the system Feature Activation Time Parameter ConfigurationFeature License Configuration Obtaining a License Key Click Generate Activating a Routing License Key Feature License CLI Commands Powering up the Fan Module Troubleshooting the InstallationPowering up the Chassis Powering up the Supervisor Modules Powering up the I/O Modules Supervisor Module does not Boot Page Replacing I/O Modules MaintenanceOne Supervisor Module in the Switch Two Supervisor Modules in the Switch Preferred Bank Firmware DownloadIntroduction Configuration Management CLI Commands Configuration File ManagementFirmware Download CLI Commands Page Ieee Standards Routing Physical Specifications Environmental Power RequirementsSafety Transportation EMC EmissionsImmunity Avaya P460 Catalog Numbers Catalog Numbers