Avaya P460 Panels, M460ML-SPV Panel, M460ML-SPV LEDs | Casio

Chapter 5

Avaya P460 Panels

Introduction

This chapter describes the front panels of the P460 switch modules, including the LEDs, ports and buttons.

M460ML-SPV Panel

M460ML-SPV modules can operate in three modes: Active, Standby and Halted. Each mode is reflected in the LEDs – further details are provided in Table 5.1.

M460ML-SPV LEDs

Figure 5.1 M460ML-SPV LEDs

Table 5.1 summarizes the functions of the LEDs for an active M460ML-SPV supervisor module.

Table 5.1	Active M460ML-SPV LEDs

LED	Description	State	Meaning


ACT	Active SPV indication	ON

ROUT	Device switching mode	ON	Layer 3

		OFF	Layer 2

OPR	CPU operation	ON	CPU boot and BIT (built-in
	System status		test) completed

		Blinking	CPU booting or running BIT
			Fan module not installed.

		OFF	CPU cannot boot (see Chapter
			12, "Troubleshooting the
			Installation")

Avaya P460 Installation and Maintenance Guide

25

Image 39

Casio manual Avaya P460 Panels, M460ML-SPV Panel, M460ML-SPV LEDs

Contents

Avaya P460 Page Contents Table of Contents Radius Ieee Ietf List of Tables List of Tables Avaya P460 Installation and Maintenance Guide List of Figures Page Before you Install the Avaya P460 Safety InformationPower Supplies Conventions Used in the Documentation FCC Notice Warranty Avaya SupportCLI Conventions Preface Avaya P460 Installation and Maintenance Guide Introduction Avaya P460 Overview Management and Monitoring Avaya P460 Key FeaturesHigh Availability Flexibility Operating Safety Avaya P460 Chassis and Module Installation Environmental Prerequisites Required Tools AC Power Requirements Key Chassis Component Location Rack Mounting Installing the P460 on a Table Top 140 mm Positioning the rack-mounting brackets P460 Rack mounting procedure Installing the Cable Guide Cable Guide Installation PSU Power Supply Unit Installation Avaya P460 Switch Fan Module Location Fan Module Replacement or Installation Installing the Avaya P460 Fan Module Location of the Avaya P460 Supervisor Modules Supervisor Module Installation Installing the P460 Supervisor Module 10 Lcoation of Avaya P460 I/O Modules Module Installation 11 I/O Module Component Location Module Installation Procedure 12 Installing P460 I/O Modules Turning on the Avaya P460 Installing a PSU Turning on a Chassis with no Modules Powering UpInserting an Additional PSU Turning on a Chassis with a Supervisor Module Only Removing or Switching off a PSU If there is one PSUIf there are two PSUs If there are three PSUs Power Management Process Power Management I/O Module Power Management Process Avaya P460 Panels M460ML-SPV PanelM460ML-SPV LEDs PWR ACT LED and OPR LED Summary Function LEDs Starting Point After Power-up or Reset LNK LAG RS-232 Port Sideband Connection M460ML-SPV Supervisor Module PortsM460ML-SPV Left and Right Pushbuttons Eth Port Outband Connection P460 Supervisor Module ASB Pushbutton M460ML-SPV ASB Alternate Software Bank Pushbutton Power Supply Panel Page Maximizing Avaya P460 Availability M460ML-SPV Supervisor Module RedundancyM460ML-SPV Supervisor Module Modes Synchronizing the Supervisor Modules Manually Following screen capture shows the process Configuration File Synchronization Maximizing Avaya P460 Availability P460 show environment power Redundant Power Supplies Sample Power Budget Calculation Calculating the Power Budget Establishing a Console Connection with the P460 Establishing Switch Access Inband Interface Connection CLI Commands Establishing a Telnet Connection with the Switch Inband M460ML-SPV Supervisor Module Fast Ethernet Console Port Establishing a Telnet Connection with the Switch Outband Outband Interface Connection CLI Commands Redundant Outband Connections Redundant Outband Connections Overview Sideband PPP Interface CLI Commands Set interface ppp ipaddrnet-mask Setting Up Sideband PPP Connection ConfigurationPage Avaya Msnm P460 Manager Welcome Running the Avaya Msnm P460 Manager P460 Device Manager Install from your Local Web Site Installing the Java Plug-inInstalling from the P460 Documentation and Utilities CD Install from the Avaya Web Site Documentation Page User Authentication Access LevelsLocal User Accounts Local User Account CLI Commands Introduction to Radius Radius Radius CLI Commands Illustrates the Radius authentication procedure User Authentication Allowed Managers Allowed Manager CLI Commands Default System Parameters Configuration Defaults Configuration Default CLI Commands Basic Switch Configuration System Parameter Configuration Identifying the systemOperating parameters Time Parameter Configuration Feature License ConfigurationFeature Activation Obtaining a License Key Click Generate Activating a Routing License Key Feature License CLI Commands Powering up the Fan Module Troubleshooting the InstallationPowering up the Chassis Powering up the Supervisor Modules Powering up the I/O Modules Supervisor Module does not Boot Page Replacing I/O Modules MaintenanceOne Supervisor Module in the Switch Two Supervisor Modules in the Switch Firmware Download IntroductionPreferred Bank Configuration File Management Firmware Download CLI CommandsConfiguration Management CLI Commands Page Ieee Standards Routing Physical Specifications Power Requirements SafetyEnvironmental EMC Emissions ImmunityTransportation Avaya P460 Catalog Numbers Catalog Numbers