Outband Interface Connection CLI Commands | Casio P460 specs

Chapter 7 Establishing Switch Access

You can now configure the P460.

You can connect the Out-band interface to either of the Supervisor modules.

Outband Interface Connection CLI Commands

In order to...	Use the following command...


Configure the management	set interface outband
interface

Enable the outband interface	enable interface outband

Disable the outband interface	disable interface outband

Enable or disable the link	set outband negotiation
negotiation protocol on the Fast
Ethernet console port

Set the speed of Fast Ethernet	set outband speed
Console port

Set the duplex mode of the Ethernet	set outband duplex
Console port

Display information on the device	show interface
network interfaces

Display outband interface	show outband
parameters

Send an ICMP echo request packets	ping
to another node on the network.

44	Avaya P460 Installation and Maintenance Guide

Image 58

Casio P460 manual Outband Interface Connection CLI Commands

Contents

Avaya P460 Page Contents Table of Contents Radius Ieee Ietf List of Tables List of Tables Avaya P460 Installation and Maintenance Guide List of Figures Page Safety Information Before you Install the Avaya P460Power Supplies FCC Notice Conventions Used in the Documentation Avaya Support WarrantyCLI Conventions Preface Avaya P460 Installation and Maintenance Guide Avaya P460 Overview Introduction Flexibility Avaya P460 Key FeaturesHigh Availability Management and Monitoring Avaya P460 Chassis and Module Installation Operating Safety Required Tools Environmental Prerequisites AC Power Requirements Chassis Component Location Key Installing the P460 on a Table Top Rack Mounting 140 mm P460 Rack mounting procedure Positioning the rack-mounting brackets Cable Guide Installation Installing the Cable Guide PSU Power Supply Unit Installation Fan Module Replacement or Installation Avaya P460 Switch Fan Module Location Installing the Avaya P460 Fan Module Supervisor Module Installation Location of the Avaya P460 Supervisor Modules Installing the P460 Supervisor Module Module Installation 10 Lcoation of Avaya P460 I/O Modules Module Installation Procedure 11 I/O Module Component Location 12 Installing P460 I/O Modules Installing a PSU Turning on the Avaya P460 Turning on a Chassis with a Supervisor Module Only Powering UpInserting an Additional PSU Turning on a Chassis with no Modules If there is one PSU Removing or Switching off a PSUIf there are two PSUs If there are three PSUs Power Management Power Management Process I/O Module Power Management Process M460ML-SPV Panel Avaya P460 PanelsM460ML-SPV LEDs PWR ACT LED and OPR LED Summary Starting Point After Power-up or Reset Function LEDs LNK LAG Eth Port Outband Connection M460ML-SPV Supervisor Module PortsM460ML-SPV Left and Right Pushbuttons RS-232 Port Sideband Connection M460ML-SPV ASB Alternate Software Bank Pushbutton P460 Supervisor Module ASB Pushbutton Power Supply Panel Page M460ML-SPV Supervisor Module Redundancy Maximizing Avaya P460 AvailabilityM460ML-SPV Supervisor Module Modes Synchronizing the Supervisor Modules Manually Configuration File Synchronization Following screen capture shows the process Maximizing Avaya P460 Availability Redundant Power Supplies P460 show environment power Calculating the Power Budget Sample Power Budget Calculation Establishing Switch Access Establishing a Console Connection with the P460 Establishing a Telnet Connection with the Switch Inband Inband Interface Connection CLI Commands Establishing a Telnet Connection with the Switch Outband M460ML-SPV Supervisor Module Fast Ethernet Console Port Outband Interface Connection CLI Commands Redundant Outband Connections Redundant Outband Connections Sideband PPP Interface CLI Commands Overview Setting Up Sideband PPP Connection Configuration Set interface ppp ipaddrnet-maskPage Avaya Msnm P460 Manager Running the Avaya Msnm P460 Manager Welcome P460 Device Manager Install from the Avaya Web Site Installing the Java Plug-inInstalling from the P460 Documentation and Utilities CD Install from your Local Web Site Documentation Page Access Levels User AuthenticationLocal User Accounts Local User Account CLI Commands Radius Introduction to Radius Illustrates the Radius authentication procedure Radius CLI Commands User Authentication Allowed Manager CLI Commands Allowed Managers Configuration Defaults Default System Parameters Configuration Default CLI Commands Basic Switch Configuration Identifying the system System Parameter ConfigurationOperating parameters Feature License Configuration Time Parameter ConfigurationFeature Activation Obtaining a License Key Click Generate Feature License CLI Commands Activating a Routing License Key Powering up the Supervisor Modules Troubleshooting the InstallationPowering up the Chassis Powering up the Fan Module Powering up the I/O Modules Supervisor Module does not Boot Page Two Supervisor Modules in the Switch MaintenanceOne Supervisor Module in the Switch Replacing I/O Modules Introduction Firmware DownloadPreferred Bank Firmware Download CLI Commands Configuration File ManagementConfiguration Management CLI Commands Page Standards Ieee Routing Specifications Physical Safety Power RequirementsEnvironmental Immunity EMC EmissionsTransportation Catalog Numbers Avaya P460 Catalog Numbers