Overview, Sideband PPP Interface CLI Commands | Casio P460 manual

Chapter 7 Establishing Switch Access

Establishing a PPP via Modem Connection with the P460 (Sideband)

Overview

The Point-to-Point Protocol (PPP) provides a Layer 2 method for transporting multi- protocol datagrams over point-to-point links. Here only IP datagrams will be exchanged, over a RS232 serial connection, between the P460 supervisor module and a remote peer (such as Ethernet) via a modem and the telephone lines. This provides remote access the sideband management interface of a P460 via a modem.

Sideband (PPP) Interface CLI Commands

In order to...	Use the following command...


Configure the device ppp interface	set interface ppp
and control a PPP session

Configure the shared secret used in	set ppp chap-secret
PPP sessions with CHAP
authentication

Set the time after which the system	set ppp incoming timeout
automatically disconnects an idle
PPP incoming session

Define the PPP authentication	set ppp authentication incoming
method

Set the baud rate used in PPP	set ppp baud-rate
sessions

Display the PPP parameters of the	show ppp session
active PPP session.

Display the authentication method	show ppp authentication
used for PPP sessions

Display the time after which the	show ppp incoming timeout
system automatically disconnects
an idle PPP incoming session

Display the baud rate used in PPP	show ppp baud-rate
sessions

Display the ppp configuration	show ppp configuration

46	Avaya P460 Installation and Maintenance Guide

Image 60

Casio P460 manual Overview, Sideband PPP Interface CLI Commands

Contents

Avaya P460 Page Contents Table of Contents Radius Ieee Ietf List of Tables List of Tables Avaya P460 Installation and Maintenance Guide List of Figures Page Before you Install the Avaya P460 Safety InformationPower Supplies FCC Notice Conventions Used in the Documentation Warranty Avaya SupportCLI Conventions Preface Avaya P460 Installation and Maintenance Guide Avaya P460 Overview Introduction Avaya P460 Key Features High AvailabilityFlexibility Management and Monitoring Avaya P460 Chassis and Module Installation Operating Safety Required Tools Environmental Prerequisites AC Power Requirements Chassis Component Location Key Installing the P460 on a Table Top Rack Mounting 140 mm P460 Rack mounting procedure Positioning the rack-mounting brackets Cable Guide Installation Installing the Cable Guide PSU Power Supply Unit Installation Fan Module Replacement or Installation Avaya P460 Switch Fan Module Location Installing the Avaya P460 Fan Module Supervisor Module Installation Location of the Avaya P460 Supervisor Modules Installing the P460 Supervisor Module Module Installation 10 Lcoation of Avaya P460 I/O Modules Module Installation Procedure 11 I/O Module Component Location 12 Installing P460 I/O Modules Installing a PSU Turning on the Avaya P460 Powering Up Inserting an Additional PSUTurning on a Chassis with a Supervisor Module Only Turning on a Chassis with no Modules Removing or Switching off a PSU If there is one PSUIf there are two PSUs If there are three PSUs Power Management Power Management Process I/O Module Power Management Process Avaya P460 Panels M460ML-SPV PanelM460ML-SPV LEDs PWR ACT LED and OPR LED Summary Starting Point After Power-up or Reset Function LEDs LNK LAG M460ML-SPV Supervisor Module Ports M460ML-SPV Left and Right PushbuttonsEth Port Outband Connection RS-232 Port Sideband Connection M460ML-SPV ASB Alternate Software Bank Pushbutton P460 Supervisor Module ASB Pushbutton Power Supply Panel Page Maximizing Avaya P460 Availability M460ML-SPV Supervisor Module RedundancyM460ML-SPV Supervisor Module Modes Synchronizing the Supervisor Modules Manually Configuration File Synchronization Following screen capture shows the process Maximizing Avaya P460 Availability Redundant Power Supplies P460 show environment power Calculating the Power Budget Sample Power Budget Calculation Establishing Switch Access Establishing a Console Connection with the P460 Establishing a Telnet Connection with the Switch Inband Inband Interface Connection CLI Commands Establishing a Telnet Connection with the Switch Outband M460ML-SPV Supervisor Module Fast Ethernet Console Port Outband Interface Connection CLI Commands Redundant Outband Connections Redundant Outband Connections Sideband PPP Interface CLI Commands Overview Setting Up Sideband PPP Connection Configuration Set interface ppp ipaddrnet-maskPage Avaya Msnm P460 Manager Running the Avaya Msnm P460 Manager Welcome P460 Device Manager Installing the Java Plug-in Installing from the P460 Documentation and Utilities CDInstall from the Avaya Web Site Install from your Local Web Site Documentation Page User Authentication Access LevelsLocal User Accounts Local User Account CLI Commands Radius Introduction to Radius Illustrates the Radius authentication procedure Radius CLI Commands User Authentication Allowed Manager CLI Commands Allowed Managers Configuration Defaults Default System Parameters Configuration Default CLI Commands Basic Switch Configuration System Parameter Configuration Identifying the systemOperating parameters Time Parameter Configuration Feature License ConfigurationFeature Activation Obtaining a License Key Click Generate Feature License CLI Commands Activating a Routing License Key Troubleshooting the Installation Powering up the ChassisPowering up the Supervisor Modules Powering up the Fan Module Powering up the I/O Modules Supervisor Module does not Boot Page Maintenance One Supervisor Module in the SwitchTwo Supervisor Modules in the Switch Replacing I/O Modules Firmware Download IntroductionPreferred Bank Configuration File Management Firmware Download CLI CommandsConfiguration Management CLI Commands Page Standards Ieee Routing Specifications Physical Power Requirements SafetyEnvironmental EMC Emissions ImmunityTransportation Catalog Numbers Avaya P460 Catalog Numbers