Installing the Avaya P460 Fan Module | Casio specification

Chapter 3 Avaya P460 Chassis and Module Installation

Figure 3.7 Installing the Avaya P460 Fan Module

Caution: You need to replace the fan module within five minutes. If you do not, the I/O modules are shut down automatically to prevent overheating of the modules. If this occurs, turn off the chassis and turn it on again.

To install a fan module:

1Remove the existing fan module. a Loosen the fastening screws.

b Gently pull the module towards you.

2Position the module in the slot with the screws to the right side of the chassis (see Figure 3.7).

3Gently slide the module in.

4Gently tighten the screws.

Avaya P460 Installation and Maintenance Guide

13

Image 27

Casio manual Installing the Avaya P460 Fan Module

Contents

Avaya P460 Page Contents Table of Contents Radius Ieee Ietf List of Tables List of Tables Avaya P460 Installation and Maintenance Guide List of Figures Page Before you Install the Avaya P460 Safety InformationPower Supplies Conventions Used in the Documentation FCC Notice Warranty Avaya SupportCLI Conventions Preface Avaya P460 Installation and Maintenance Guide Introduction Avaya P460 Overview Management and Monitoring Avaya P460 Key FeaturesHigh Availability Flexibility Operating Safety Avaya P460 Chassis and Module Installation Environmental Prerequisites Required Tools AC Power Requirements Key Chassis Component Location Rack Mounting Installing the P460 on a Table Top 140 mm Positioning the rack-mounting brackets P460 Rack mounting procedure Installing the Cable Guide Cable Guide Installation PSU Power Supply Unit Installation Avaya P460 Switch Fan Module Location Fan Module Replacement or Installation Installing the Avaya P460 Fan Module Location of the Avaya P460 Supervisor Modules Supervisor Module Installation Installing the P460 Supervisor Module 10 Lcoation of Avaya P460 I/O Modules Module Installation 11 I/O Module Component Location Module Installation Procedure 12 Installing P460 I/O Modules Turning on the Avaya P460 Installing a PSU Turning on a Chassis with no Modules Powering UpInserting an Additional PSU Turning on a Chassis with a Supervisor Module Only Removing or Switching off a PSU If there is one PSUIf there are two PSUs If there are three PSUs Power Management Process Power Management I/O Module Power Management Process Avaya P460 Panels M460ML-SPV PanelM460ML-SPV LEDs PWR ACT LED and OPR LED Summary Function LEDs Starting Point After Power-up or Reset LNK LAG RS-232 Port Sideband Connection M460ML-SPV Supervisor Module PortsM460ML-SPV Left and Right Pushbuttons Eth Port Outband Connection P460 Supervisor Module ASB Pushbutton M460ML-SPV ASB Alternate Software Bank Pushbutton Power Supply Panel Page Maximizing Avaya P460 Availability M460ML-SPV Supervisor Module RedundancyM460ML-SPV Supervisor Module Modes Synchronizing the Supervisor Modules Manually Following screen capture shows the process Configuration File Synchronization Maximizing Avaya P460 Availability P460 show environment power Redundant Power Supplies Sample Power Budget Calculation Calculating the Power Budget Establishing a Console Connection with the P460 Establishing Switch Access Inband Interface Connection CLI Commands Establishing a Telnet Connection with the Switch Inband M460ML-SPV Supervisor Module Fast Ethernet Console Port Establishing a Telnet Connection with the Switch Outband Outband Interface Connection CLI Commands Redundant Outband Connections Redundant Outband Connections Overview Sideband PPP Interface CLI Commands Set interface ppp ipaddrnet-mask Setting Up Sideband PPP Connection ConfigurationPage Avaya Msnm P460 Manager Welcome Running the Avaya Msnm P460 Manager P460 Device Manager Install from your Local Web Site Installing the Java Plug-inInstalling from the P460 Documentation and Utilities CD Install from the Avaya Web Site Documentation Page User Authentication Access LevelsLocal User Accounts Local User Account CLI Commands Introduction to Radius Radius Radius CLI Commands Illustrates the Radius authentication procedure User Authentication Allowed Managers Allowed Manager CLI Commands Default System Parameters Configuration Defaults Configuration Default CLI Commands Basic Switch Configuration System Parameter Configuration Identifying the systemOperating parameters Time Parameter Configuration Feature License ConfigurationFeature Activation Obtaining a License Key Click Generate Activating a Routing License Key Feature License CLI Commands Powering up the Fan Module Troubleshooting the InstallationPowering up the Chassis Powering up the Supervisor Modules Powering up the I/O Modules Supervisor Module does not Boot Page Replacing I/O Modules MaintenanceOne Supervisor Module in the Switch Two Supervisor Modules in the Switch Firmware Download IntroductionPreferred Bank Configuration File Management Firmware Download CLI CommandsConfiguration Management CLI Commands Page Ieee Standards Routing Physical Specifications Power Requirements SafetyEnvironmental EMC Emissions ImmunityTransportation Avaya P460 Catalog Numbers Catalog Numbers