Manuals / Brands / Power Tools / Router / Cisco Systems / Power Tools / Router

Cisco Systems ASR 1004 Connect DC Power to the Router

1 38

Download 38 pages, 2.53 Mb

15

Step 3 Insert the AC power cable into the power supply inlet.

Step 4 Plug the power supply cable into the power source.

Step 5 The power supply LEDs light when power is supplied to the router.

Figure 10 Cisco ASR 1004 Router AC Power Supply

Step 6 Turn the power supply Standby switch to On (|) position.

This completes the procedure for connecting AC-input power.

Connect DC Power to the Router

This section provides instructions for installing the DC power supply into the Cisco ASR 1004 Router. Read the safety warnings

and important notices before you begin.

Warning

Installation of the equipment must comply with local and national electrical codes.

Statement 1074

Warning

Never install an AC power module and a DC power module in the same chassis.

Statement 1050

Warning

When installing or replacing the unit, the ground connection must always be made first and disconnected last.

Statement 1046

1AC power supply Standby switch 4AC power supply fan

2AC power supply LEDs 5AC power inlet

3DB-25 Alarm connector 6AC power supply handle

280184

OUTPUT INPUT

FAIL OK OK

FAN

100V-240V~ 12A-5A

50-60Hz ALARMS

60V

1A MAX

OUTPUT INPUT

FAIL OK OK

FAN

100V-240V~ 12A-5A

50-60Hz ALARMS

60V

1A MAX

1 2

34

6

5

Contents

Main 1 Document Revision History Documentation Survey Obtaining Documentation and Submitting a Service Request Document Version Date Change Summary 2 Site Preparation and Unpacking Tools and Parts Prepare for Equipment Shelf or Tabletop Installation Prepare for Rack-Mount Installation 3 Attach the Rack-Mount BracketsChassis Front-Mounted 1 Front rack-mount bracket 3 2 Front rack-mount bracket screws 4 Attach the Rack-Mount BracketsChassis Rear-Mounted 4 1 Rear rack-mount bracket ear and holes 3 2 Four-Post Rack Installation This section describes the types of racks used for rack-mounting the chassis. Figure 3 Installing the Cisco ASR 1004 Router in a Four-Post Rack STAT Page Two-Post Rack Installation The Cisco ASR 1004 Router can be installed in a two-post rack, either 19 inch or 23 inch. STA 1 Rack-mount bracket ear and holes 2 Figure 4 Installing a Cisco ASR 1004 Router in a Two-Post Rack Attach the Cable-Management Bracket Figure 5 Attaching the Cable-Management Bracket to the Cisco ASR 1004 Router CARRIER DISK CRIT Chassis Ground Connection Installation 1 Cable-management bracket screws 3 2 MAJ STBY ACTV STAT LINK Figure 7 shows how to attach the grounding screws. 1 1 Chassis earth ground studs and lead wire 3 2 Grounding screws 4 T 4 Console and Auxiliary Port Cable Connections 1 CONconsole port 2 Management Ethernet Port Cable Connection DISK CARRIER PWR ASR1000-RP1 5 Connect AC Power to the Router Connect DC Power to the Router 1 AC power supply Standby switch 4 2 AC power supply LEDs 5 3 DB-25 Alarm connector 6 Page Installing the DC Ground Lugs ground stud components in the following order: Wiring the DC-Input Power Source 1 DC power supply grounding stud 3 2 Grounding stud screws 4 5 4 3 1 Ground lug and positive lead wire 4 2 3 Verifying Power Supply Operation Start the Cisco ASR 1004 Router Page Page Page 6 Using the Console Interface Configure Global Parameters Using the Setup Facility Page Page Page Page Check the Running Configuration Settings Save the Running Configuration to NVRAM Perform Other Configuration Tasks 7 Power Off the Cisco ASR 1004 Router Remove and Replace a Power Supply Remove and Then Replace an AC Power Supply Remove and Then Replace a DC Power Supply Page 1 Ground lug and positive lead wire 4 2 3 Install and Remove the SPA Interface Processor (SIP) 1 2 1 2 3 4 Remove the Shared Port Adapter Figure 16 Installing and Removing the Shared Port Adapter ASR1000-SIP10