Manuals / Brands / Power Tools / Router / Cisco Systems / Power Tools / Router

Cisco Systems ASR 1004 Installing the DC Ground Lugs

1 38

Download 38 pages, 2.53 Mb

17

Figure 10 shows the DC power supply for the Cisco ASR 1004 Router.

DC Power Supply for the Cisco ASR 1004 Router

The Cisco ASR1004 has two of the same type power supplies in power supply Slot 0 and power supply Slot 1.

Caution Before you connect DC-input power, you must install the DC power ground leads to the DC power supply.

Caution To make sure that the equipment is reliably connected to earth ground, follow the grounding procedure

instructions.

Obtain these necessary tools and equipment:

•Number 2 Phillips screwdriver

•A 3/16-inch flat-blade screwdriver

Installing the DC Ground Lugs

To install the grounding lugs on the DC power supply, follow these instructions. Figure 11 shows the location of the DC power

supply grounding stud.

1DC power supply terminal block and plastic cover 5DC power supply earth ground symbol

2DC power supply LEDs 6DC power supply On (I)/ Off (O)

3DB-25 alarm connector 7DC power supply handle

4DC power supply fan

280185

OUTPUT INPUT

FAIL OK OK

FAN

60V

1A MAX

OUTPUT INPUT

FAIL OK OK

FAN

60V

1A MAX

12

345

67

Contents

Main 1 Document Revision History Documentation Survey Obtaining Documentation and Submitting a Service Request Document Version Date Change Summary 2 Site Preparation and Unpacking Tools and Parts Prepare for Equipment Shelf or Tabletop Installation Prepare for Rack-Mount Installation 3 Attach the Rack-Mount BracketsChassis Front-Mounted 1 Front rack-mount bracket 3 2 Front rack-mount bracket screws 4 Attach the Rack-Mount BracketsChassis Rear-Mounted 4 1 Rear rack-mount bracket ear and holes 3 2 Four-Post Rack Installation This section describes the types of racks used for rack-mounting the chassis. Figure 3 Installing the Cisco ASR 1004 Router in a Four-Post Rack STAT Page Two-Post Rack Installation The Cisco ASR 1004 Router can be installed in a two-post rack, either 19 inch or 23 inch. STA 1 Rack-mount bracket ear and holes 2 Figure 4 Installing a Cisco ASR 1004 Router in a Two-Post Rack Attach the Cable-Management Bracket Figure 5 Attaching the Cable-Management Bracket to the Cisco ASR 1004 Router CARRIER DISK CRIT Chassis Ground Connection Installation 1 Cable-management bracket screws 3 2 MAJ STBY ACTV STAT LINK Figure 7 shows how to attach the grounding screws. 1 1 Chassis earth ground studs and lead wire 3 2 Grounding screws 4 T 4 Console and Auxiliary Port Cable Connections 1 CONconsole port 2 Management Ethernet Port Cable Connection DISK CARRIER PWR ASR1000-RP1 5 Connect AC Power to the Router Connect DC Power to the Router 1 AC power supply Standby switch 4 2 AC power supply LEDs 5 3 DB-25 Alarm connector 6 Page Installing the DC Ground Lugs ground stud components in the following order: Wiring the DC-Input Power Source 1 DC power supply grounding stud 3 2 Grounding stud screws 4 5 4 3 1 Ground lug and positive lead wire 4 2 3 Verifying Power Supply Operation Start the Cisco ASR 1004 Router Page Page Page 6 Using the Console Interface Configure Global Parameters Using the Setup Facility Page Page Page Page Check the Running Configuration Settings Save the Running Configuration to NVRAM Perform Other Configuration Tasks 7 Power Off the Cisco ASR 1004 Router Remove and Replace a Power Supply Remove and Then Replace an AC Power Supply Remove and Then Replace a DC Power Supply Page 1 Ground lug and positive lead wire 4 2 3 Install and Remove the SPA Interface Processor (SIP) 1 2 1 2 3 4 Remove the Shared Port Adapter Figure 16 Installing and Removing the Shared Port Adapter ASR1000-SIP10