Cisco Systems ASR 1004

enable password tests

line vty 0 4

password test

no snmp-server

ip routing

no bridge 1

no clns routing

interface GigabitEthernet0/0/0

shutdown

no ip address

interface GigabitEthernet0/0/1

shutdown

no ip address

interface GigabitEthernet0/0/2

shutdown

no ip address

interface GigabitEthernet0/0/3

shutdown

no ip address

interface GigabitEthernet0/1/0

shutdown

no ip address

interface GigabitEthernet0/1/1

shutdown

no ip address

interface FastEthernet0/3/0

shutdown

no ip address

interface FastEthernet0/3/1

shutdown

no ip address

interface FastEthernet0/3/2

shutdown

no ip address

interface FastEthernet0/3/3

shutdown

no ip address

interface FastEthernet0/3/4

shutdown

no ip address

interface FastEthernet0/3/5

shutdown

no ip address

interface FastEthernet0/3/6

shutdown

no ip address

interface FastEthernet0/3/7

shutdown

no ip address

interface GigabitEthernet0

Contents

Main 1 Document Revision History Documentation Survey Obtaining Documentation and Submitting a Service Request Document Version Date Change Summary 2 Site Preparation and Unpacking Tools and Parts Prepare for Equipment Shelf or Tabletop Installation Prepare for Rack-Mount Installation 3 Attach the Rack-Mount BracketsChassis Front-Mounted 1 Front rack-mount bracket 3 2 Front rack-mount bracket screws 4 Attach the Rack-Mount BracketsChassis Rear-Mounted 4 1 Rear rack-mount bracket ear and holes 3 2 Four-Post Rack Installation This section describes the types of racks used for rack-mounting the chassis. Figure 3 Installing the Cisco ASR 1004 Router in a Four-Post Rack STAT Page Two-Post Rack Installation The Cisco ASR 1004 Router can be installed in a two-post rack, either 19 inch or 23 inch. STA 1 Rack-mount bracket ear and holes 2 Figure 4 Installing a Cisco ASR 1004 Router in a Two-Post Rack Attach the Cable-Management Bracket Figure 5 Attaching the Cable-Management Bracket to the Cisco ASR 1004 Router CARRIER DISK CRIT Chassis Ground Connection Installation 1 Cable-management bracket screws 3 2 MAJ STBY ACTV STAT LINK Figure 7 shows how to attach the grounding screws. 1 1 Chassis earth ground studs and lead wire 3 2 Grounding screws 4 T 4 Console and Auxiliary Port Cable Connections 1 CONconsole port 2 Management Ethernet Port Cable Connection DISK CARRIER PWR ASR1000-RP1 5 Connect AC Power to the Router Connect DC Power to the Router 1 AC power supply Standby switch 4 2 AC power supply LEDs 5 3 DB-25 Alarm connector 6 Page Installing the DC Ground Lugs ground stud components in the following order: Wiring the DC-Input Power Source 1 DC power supply grounding stud 3 2 Grounding stud screws 4 5 4 3 1 Ground lug and positive lead wire 4 2 3 Verifying Power Supply Operation Start the Cisco ASR 1004 Router Page Page Page 6 Using the Console Interface Configure Global Parameters Using the Setup Facility Page Page Page Page Check the Running Configuration Settings Save the Running Configuration to NVRAM Perform Other Configuration Tasks 7 Power Off the Cisco ASR 1004 Router Remove and Replace a Power Supply Remove and Then Replace an AC Power Supply Remove and Then Replace a DC Power Supply Page 1 Ground lug and positive lead wire 4 2 3 Install and Remove the SPA Interface Processor (SIP) 1 2 1 2 3 4 Remove the Shared Port Adapter Figure 16 Installing and Removing the Shared Port Adapter ASR1000-SIP10