Manuals / Brands / Power Tools / Router / Cisco Systems / Power Tools / Router

Cisco Systems ASR 1004 Verifying Power Supply Operation, Start the Cisco ASR 1004 Router

1 38

Download 38 pages, 2.53 Mb

20

Step 8 Connect the other ends of the terminal block cables to the site ground connection. Move the circuit-breaker switch to

the On position (|).

This completes the procedure for connecting DC-input power. Your installation is complete. Proceed to the “Start the System”

section on page 14 to start the router.

Note After powering off the router, wait a minimum of 30 seconds before powering it on again.

Verifying Power Supply Operation

Follow this procedure to verify power supply is operating correctly.

Step 1 Check that the power supply LEDs are:

•INPUT OK is green

•FAN OK is green

•OUTPUT FAILED is not illuminated

Step 2 To ensure that the power supply state is OK, type the show platform command. This output sample is from a Cisco

ASR1004 router.

MCP_SCAL_R1#sho plat

Chassis type: ASR1004

The following output displays:

MCP_SCAL_R1#

If the LEDs indicate a power problem or the power supply state is ps,fail, then contact a customer service representatives for

assistance or additional instructions.

Start the Cisco ASR 1004 Router

After installing your Cisco ASR 1004 Router and connecting cables, start the router as follows.

Step 1 Check for the following:

Slot Type State Insert Time

0 ASR1000-SIP10 ok 00:03:19

1 ASR1000-SIP10 ok 00:03:19

RP0 ASR1000-RP1 ok,active 00:03:19

FP0 ASR1000-ESP20 ok,active 00:03:19

P0 ASR1004-PWR-AC ok 00:02:50

P1 ASR1004-PWR-AC ps, fail 00:02:50

Slot CPLD Version Firmware Version

0 07091401 12.2(33r)XN2

1 07091401 12.2(33r)XN2

RP0 08060301 12.2(0:0)

FP0 08041102 12.2(33r)XN2

Contents

Main 1 Document Revision History Documentation Survey Obtaining Documentation and Submitting a Service Request Document Version Date Change Summary 2 Site Preparation and Unpacking Tools and Parts Prepare for Equipment Shelf or Tabletop Installation Prepare for Rack-Mount Installation 3 Attach the Rack-Mount BracketsChassis Front-Mounted 1 Front rack-mount bracket 3 2 Front rack-mount bracket screws 4 Attach the Rack-Mount BracketsChassis Rear-Mounted 4 1 Rear rack-mount bracket ear and holes 3 2 Four-Post Rack Installation This section describes the types of racks used for rack-mounting the chassis. Figure 3 Installing the Cisco ASR 1004 Router in a Four-Post Rack STAT Page Two-Post Rack Installation The Cisco ASR 1004 Router can be installed in a two-post rack, either 19 inch or 23 inch. STA 1 Rack-mount bracket ear and holes 2 Figure 4 Installing a Cisco ASR 1004 Router in a Two-Post Rack Attach the Cable-Management Bracket Figure 5 Attaching the Cable-Management Bracket to the Cisco ASR 1004 Router CARRIER DISK CRIT Chassis Ground Connection Installation 1 Cable-management bracket screws 3 2 MAJ STBY ACTV STAT LINK Figure 7 shows how to attach the grounding screws. 1 1 Chassis earth ground studs and lead wire 3 2 Grounding screws 4 T 4 Console and Auxiliary Port Cable Connections 1 CONconsole port 2 Management Ethernet Port Cable Connection DISK CARRIER PWR ASR1000-RP1 5 Connect AC Power to the Router Connect DC Power to the Router 1 AC power supply Standby switch 4 2 AC power supply LEDs 5 3 DB-25 Alarm connector 6 Page Installing the DC Ground Lugs ground stud components in the following order: Wiring the DC-Input Power Source 1 DC power supply grounding stud 3 2 Grounding stud screws 4 5 4 3 1 Ground lug and positive lead wire 4 2 3 Verifying Power Supply Operation Start the Cisco ASR 1004 Router Page Page Page 6 Using the Console Interface Configure Global Parameters Using the Setup Facility Page Page Page Page Check the Running Configuration Settings Save the Running Configuration to NVRAM Perform Other Configuration Tasks 7 Power Off the Cisco ASR 1004 Router Remove and Replace a Power Supply Remove and Then Replace an AC Power Supply Remove and Then Replace a DC Power Supply Page 1 Ground lug and positive lead wire 4 2 3 Install and Remove the SPA Interface Processor (SIP) 1 2 1 2 3 4 Remove the Shared Port Adapter Figure 16 Installing and Removing the Shared Port Adapter ASR1000-SIP10