About Slots and Interfaces | Cisco Systems ISR4451XK9 manual

Chapter 1 Overview of the Cisco 4451-X Integrated Services Router

About Slots and Interfaces

Fans, Ventilation, and Airflow

Chassis Ventilation

An internal fan tray consisting of 4 fans provides chassis cooling. An onboard temperature sensor controls the fan speed. The fans are always on when the router is powered on. Under most conditions, the fans operate at the slowest speed to conserve power and reduce fan noise. The fans operate at the higher speeds when necessary under conditions of higher ambient temperature. To replace a fan tray, see the “Replacing a Fan Tray” section on page 6-34.

•Figure 1-8shows the Cisco ISR 4451-X airflow.

Figure 1-8 Cisco ISR 4451-X Airflow)

303009

About Slots and Interfaces

This section covers the following topics:

•About Slot, Subslot (Bay), and Port Numbering, page 1-17

•Slot Numbering, page 1-19

•Subslot/Bay Numbering, page 1-20

•Gigabit Ethernet Management, page 1-20

•About Fixed Interfaces, page 1-20

About Slot, Subslot (Bay), and Port Numbering

The Cisco ISR 4451-X supports two types of interface modules: Enhanced Service Modules (SMs) and Network Modules (NIMs).

		Hardware Installation Guide for the Cisco 4451-X Integrated Services Router

	OL-27644-01			1-17
	OL-27644-01			1-17

Image 35

Cisco Systems ISR4451XK9 manual About Slots and Interfaces, Fans, Ventilation, and Airflow

Contents

Cisco Systems, Inc Page N T E N T S Additional Slots Ports and Cabling Safety Warnings Accessing Internal Modules Installing and Removing NIMs and SMs OIR Procedures Audience Objectives Chapter Title Description Organization Convention Indication Conventions Warnung Wichtige Sicherheitshinweise Bewaar Deze Instructies Aviso Instruções Importantes DE Segurança Avvertenza Importanti Istruzioni Sulla Sicurezza Xiv GEM Disse Anvisninger Xvi Related Documentation Searching for Cisco Documents Obtaining Documentation and Submitting a Service Request About the Cisco ISR Overview of the Cisco 4451-X Integrated Services Router Safety Warnings Chassis Views Safety Warnings for Finland, Norway and Sweden On page 1-4- Bezel view with one PSU Cisco ISR 4451-X Chassis Bezel side of the Cisco ISR 4451-X with two PSUs Bezel Side Leds of the Single PSU Cisco ISR 4451-X Model ISC slot Modular HDD Slot Factory-configuredLocating the Serial Number, PID, VID and Clei Platform Summary Product ID Labels on Cisco ISRFor Additional Help Locating Labels on the Router Label Description Built-in Interface Ports Hardware Features Front Panel PoE+ Ports Dual Mode GE/SFP PortsFront Panel Ethernet Ports USB Serial Console Port Represents Color Description Location LED IndicatorsInternal PoE card Active Left Will be off Status Green Tbd Side Ports 0, 1 Amber Off Not presentConsole Active Right Will be off External Slots Two PoE PSUs installed and operating Redundant modeRemovable and Interchangeable Modules and Cards Internal Slots Solid State Drives Network Interface Modules Cisco UCS E-Series Server ModulesCompact Flash Memory Packet Voice Digital Signal Processor ModulesPower Supplies This section covers the following topics About Slots and InterfacesFans, Ventilation, and Airflow About Slot, Subslot Bay, and Port Numbering 9shows the ports and slots on the Cisco ISR 4451-Xs Tuple Example Slot Bay Port Slots are numbered 0, 1 Slot NumberingAbout Slot Console port About Fixed Interfaces SpecificationsSubslot/Bay Numbering Gigabit Ethernet Management Ports Description SpecificationPower Is disabled. See xxxx for a list of supported modules Description Specification Regulatory For detailed compliance information, see the Regulatory Integrated Services Router document Periodic Inspection and Cleaning Standard Warning Statements General Safety WarningsPage Page Page Follow these guidelines to ensure general safety Safety RecommendationsSafety with Electricity Preparing for Router Installation Safety Recommendations Site Selection Guidelines General PrecautionsGeneral Site Requirements Preventing Electrostatic Discharge Damage Site Environmental Requirements Environmental Characteristic Minimum Maximum Rack Requirements Physical CharacteristicsCharacteristics Height Width Depth Weight Router Environmental Requirements Network Cabling Specifications Power Guidelines and Requirements Console Port Connections Console and Auxiliary Port Considerations USB Console OS Compatibility Auxiliary Port Connections Ethernet Connections Preparing for Network Connections OL-27644-01 Task Verified by Date Installation Checklist Creating a Site Log Installing and Connecting the Router Page Slot and Port Numbers CLI Console AccessWhat You Need to Know Before You Begin Unpacking the Router Installing the Router Statement Rack-Mounting the ChassisAttaching Rack-Mount Brackets Inch SBC brackets Inch EIA brackets Inch SBC 1 brackets Inch EIA brackets Mounting the Router in a Rack Bracket Installation for Back Mounting 5shows a typical installation in a rack Mounting screws Grounding the Chassis Setting the Chassis on a Desktop Chassis Grounding Chassis Ground Connection on the Cisco ISR 4451-X Chassis Connecting Power 15A, 120VAC 16A, 240VAC. Statement Connecting to AC Power Serial RJ-45 EIA RJ-45 Connecting to a Console Terminal or ModemConnecting to the Serial Port with Microsoft Windows Port Type Cable Section No parity Stop bit No flow control Connecting to the Console Port with Mac OS To disconnect the OS X USB console from the Terminal window Connecting to the Console Port with Linux Installing the Cisco Microsoft Windows Vista USB Driver Installing the Cisco Microsoft Windows XP USB DriverInstalling the Cisco Microsoft Windows 2000 USB Driver Using the Setup.exe program Uninstalling the Cisco Microsoft Windows USB DriverUsing the Add Remove Programs utility Uninstalling the Cisco Microsoft Windows Vista USB Driver Connecting to the Auxiliary Port Connecting a Modem to the Cisco ISR Connecting WAN, LAN, and Voice Interfaces OL-27644-01 Port or Connection Port Type, Color1 Cable Connection Procedures and PrecautionsData sheet Ports and Cabling OL-27644-01 Using Cisco Setup Command Facility Performing the Initial Configuration on the Router Basic management setup configures only enough connectivity You are now in the Setup Configuration UtilityRouter when it is booted into Cisco IOS-XE To proceed using the setup command facility, enter yes Summary of the available interfaces is displayed Following configuration command script was created User prompt is displayed Completing the Configuration Press Return to bring up the Router prompt Using Cisco IOS-XE CLI-Manual ConfigurationType enable to enter privileged Exec mode Example Configuring the Router HostnameCommand or Action Purpose Configuring the Enable and Enable Secret Passwords Configuring the Console Idle Privileged Exec Timeout Gigabit Ethernet Management Interface Overview Gigabit Ethernet Port Numbering Default Gigabit Ethernet ConfigurationConfiguring Gigabit Ethernet Interfaces Troubleshooting Configuration modeOptional Adds a description to an interface configuration Description helps you remember what is attached to Configuring the GigabitEthernet Interface Example Configuration ExamplesSpecifying a Default Route or Gateway of Last Resort Configuring IP Routing and IP Protocols Gateway of Last Resort Default RoutesDefault Network Establishes a static route Enables IP routing Configuration Examples Line vty ? command Starts the line configuration command collection mode forVirtual terminal lines vty for remote console access Make sure that you configure all vty lines on your What to Do Next Configuring the Auxiliary Line Auxiliary line Enable Configure terminal Line aux Verifying Network Connectivity Saving Backup Copies of Configuration and System Image Saving Your Router Configuration Copying from Flash Memory to a Tftp Server Example Copying the Startup Configuration to a Tftp Server Example 2012 Initial Configuration Verifying the Initial Configuration Verifying the Initial Configuration ROM Monitor Overview ROM Monitor Overview and Basic ProceduresEnvironmental Variables and the Configuration Register Checking the Current ROMmon Version Entering ROM Monitor ModeAccessing ROM Monitor Mode with a Terminal Connection Network Management Access and ROM Monitor Mode XXX-XXXX-XX Examples Commonly Used ROM Monitor CommandsDisplaying the Available ROM Monitor Commands 2describes the available help commands for ROM Monitor mode Changing the ROM Monitor Prompt Displaying the Configuration Register SettingEnvironment Variable Settings Frequently Used Environmental Variables Displaying Environment Variable Settings Respond to each prompt as instructed Exiting ROM Monitor ModeEntering Environment Variable Settings Saving Environment Variable Settings Resets and initializes the router Configuration ExampleInitiates the configuration register configuration prompts Upgrading the ROMmon for a Router Example of Upgrade Router# show romvar FRUs Internal and External Modules Safety Warnings 1029 T1 SFP Statement Replacing the Cover Accessing Internal ModulesRemoving and Replacing the Chassis Cover Removing the Cover Cover screws Locating Internal and External Slots for Modules ISC slot DIMMs NIM-SSD Slot 0 Factory-configuredOverview of the SSD Carrier Card NIM NIM-SSD 3shows the front panel of the SSD NIM Overview Solid state drive Green SSD present Slot Off No SSD in slot LEDs on the NIM-SSD1describes the LEDs on the NIM-SSD as shown in Figure Represents Color Description Transportation and Storage 2lists the specifications of the SSD Carrier Card NIMPower consumption maximum 20W Environmental Top View of the SSD Carrier Card NIM with Serial Number Solid State Drives SSD Solid State Drive SSD Opening the SSD Slot Cover Installing the SSD Drives into the NIM Carrier Card Removing the SSD Drives from the NIM-SSD 10 Pulling out the Solid State Drives Tabs to pull out the SSD drives Restrictions Removing and Replacing the Cisco ISR 4451-X NIM-SSD Drives Removing the NIM-SSD from the Router 12 Removing the NIM-SSD from the Router Locating and Orienting Dimm Installing and Removing DDR DIMMsReplacing the NIM-SSD on the Router 14 Dimm Showing Polarization Notch Polarization notch 15 Removing a Dimm Removing a Dimm 16 Dimm Showing Polarization Notch Installing a Dimm 17 Handling the DIMMs 18 Installing a Dimm Installing and Removing NIMs and SMs Removing an SM or NIM Installing an SMSoftware Requirement for SMs Locating an SM or NIM Verifying SM Installation Installing and Removing the PVDM4 PVDM4 Location and Orientation Tools and Equipment Required During Installation Remove the cover Installing the PVDM4 on the Motherboard of the Cisco ISRAny module replacement Ground Standoffs Screws ConnectorRemoving the PVDM4 from the Motherboard of the Cisco ISR 22 Network Interface Module with PVDM4 Captive Screws Ports Network Card Removing and Replacing the USB Flash Token Memory Stick This completes the USB Flash memory installation procedure Replacing the Cisco ISR 4451-X Power Supply 24 Power Supply Unit Inserting PoE Supply in an Ethernet Switch Network Module Replacing the Power Supply on the Cisco ISR 4451-Xs Before Hot-Swapping a Fan Tray Cisco ISR 4451-X Power and RPS Error MessagesReplacing a Fan Tray Replacing the Cisco ISR 4451-X Fan Tray Fan Tray 26 Cisco ISR 4451-X Fan Tray Replacement Removing a CompactFlash Memory Card Removing and Installing a CompactFlash Memory Card Installing a CompactFlash Memory Card Installing SFP Modules 1546.12 DWDM-SFP-4692 DWDM-SFP-43731543.73 DWDM-SFP-4453 1544.53 DWDM-SFP-4612 Connect the network cable to the SFP module Laser Safety GuidelinesRemoving SFP Modules Disconnect the SFP latch. See Figure Removing, Replacing, and Installing an Internal PoE Card 29 Location of the PoE Card Requirement Online Insertion and Removal OIR Hot-Swapping Inserting a Data or Voice Module OIR ProceduresHot-Swapping Procedures Removing a Module