Connecting a Modem to the Cisco ISR | Cisco Systems ISR4451XK9

Chapter 3 Installing and Connecting the Router

Connecting WAN, LAN, and Voice Interfaces

Figure 3-9 Connecting a Modem to the Cisco ISR 4451-X

AUX

1

EN

AUX

CONSOLE

CONSOLE

1

302958

	2	3		4

1	RJ-45 AUX port		3	RJ-45 to DB-9

2	DB-9 to DB-25 adapter		4	Modem

Step 2 Connect the DB-9 end of the console cable to the DB-9 end of the modem adapter.

Step 3 Connect the DB-25 end of the modem adapter to the modem.

Step 4 Make sure that your modem and the router auxiliary port are configured for the same transmission speed (up to 115200 bps is supported) and for mode control with data carrier detect (DCD) and data terminal ready (DTR) operations.

Connecting WAN, LAN, and Voice Interfaces

This section describes how to connect WAN, LAN, and voice interface cables. It covers the following topics:

•Ports and Cabling, page 3-22

•Connection Procedures and Precautions, page 3-22

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

		Cisco 4400 Series Hardware Installation Guide
		Cisco 4400 Series Hardware Installation Guide
	OL-27644-01			3-20
	OL-27644-01			3-20

Image 80

Cisco Systems ISR4451XK9 manual Connecting WAN, LAN, and Voice Interfaces, Connecting a Modem to the Cisco ISR

Contents

Cisco Systems, Inc Page N T E N T S Additional Slots Ports and Cabling Safety Warnings Accessing Internal Modules Installing and Removing NIMs and SMs OIR Procedures Objectives Audience Organization Chapter Title Description Conventions Convention Indication Bewaar Deze Instructies Warnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla Sicurezza Aviso Instruções Importantes DE Segurança Xiv GEM Disse Anvisninger Xvi Related Documentation Obtaining Documentation and Submitting a Service Request Searching for Cisco Documents Overview of the Cisco 4451-X Integrated Services Router About the Cisco ISR Safety Warnings Safety Warnings for Finland, Norway and Sweden Chassis Views Cisco ISR 4451-X Chassis On page 1-4- Bezel view with one PSU Bezel side of the Cisco ISR 4451-X with two PSUs Bezel Side Leds of the Single PSU Cisco ISR 4451-X Model Modular HDD Slot Factory-configured Locating the Serial Number, PID, VID and CleiPlatform Summary ISC slot Labels on Cisco ISR For Additional Help Locating Labels on the RouterLabel Description Product ID Hardware Features Built-in Interface Ports Dual Mode GE/SFP Ports Front Panel Ethernet PortsUSB Serial Console Port Front Panel PoE+ Ports Represents Color Description Location LED IndicatorsInternal PoE card Active Left Will be off Status Green Tbd Side Ports 0, 1 Amber Off Not presentConsole Active Right Will be off External Slots Two PoE PSUs installed and operating Redundant modeRemovable and Interchangeable Modules and Cards Internal Slots Solid State Drives Network Interface Modules Cisco UCS E-Series Server ModulesCompact Flash Memory Packet Voice Digital Signal Processor ModulesPower Supplies About Slots and Interfaces Fans, Ventilation, and AirflowAbout Slot, Subslot Bay, and Port Numbering This section covers the following topics Tuple Example Slot Bay Port 9shows the ports and slots on the Cisco ISR 4451-Xs Slot Numbering About SlotConsole port Slots are numbered 0, 1 Specifications Subslot/Bay NumberingGigabit Ethernet Management About Fixed Interfaces Description Specification PowerIs disabled. See xxxx for a list of supported modules Ports Description Specification Regulatory Integrated Services Router document For detailed compliance information, see the Regulatory Periodic Inspection and Cleaning General Safety Warnings Standard Warning StatementsPage Page Page Follow these guidelines to ensure general safety Safety RecommendationsSafety with Electricity Preparing for Router Installation Safety Recommendations General Precautions General Site RequirementsPreventing Electrostatic Discharge Damage Site Selection Guidelines Environmental Characteristic Minimum Maximum Site Environmental Requirements Physical Characteristics CharacteristicsHeight Width Depth Weight Rack Requirements Router Environmental Requirements Power Guidelines and Requirements Network Cabling Specifications Console and Auxiliary Port Considerations Console Port Connections Auxiliary Port Connections USB Console OS Compatibility Preparing for Network Connections Ethernet Connections OL-27644-01 Installation Checklist Task Verified by Date Creating a Site Log Installing and Connecting the Router Page CLI Console Access What You Need to KnowBefore You Begin Slot and Port Numbers Installing the Router Unpacking the Router Statement Rack-Mounting the ChassisAttaching Rack-Mount Brackets Inch SBC 1 brackets Inch EIA brackets Inch SBC brackets Inch EIA brackets Bracket Installation for Back Mounting Mounting the Router in a Rack 5shows a typical installation in a rack Grounding the Chassis Mounting screws Setting the Chassis on a Desktop Chassis Grounding Connecting Power Chassis Ground Connection on the Cisco ISR 4451-X Chassis Connecting to AC Power 15A, 120VAC 16A, 240VAC. Statement Connecting to a Console Terminal or Modem Connecting to the Serial Port with Microsoft WindowsPort Type Cable Section Serial RJ-45 EIA RJ-45 Connecting to the Console Port with Mac OS No parity Stop bit No flow control Connecting to the Console Port with Linux To disconnect the OS X USB console from the Terminal window Installing the Cisco Microsoft Windows Vista USB Driver Installing the Cisco Microsoft Windows XP USB DriverInstalling the Cisco Microsoft Windows 2000 USB Driver Using the Setup.exe program Uninstalling the Cisco Microsoft Windows USB DriverUsing the Add Remove Programs utility Connecting to the Auxiliary Port Uninstalling the Cisco Microsoft Windows Vista USB Driver Connecting WAN, LAN, and Voice Interfaces Connecting a Modem to the Cisco ISR OL-27644-01 Connection Procedures and Precautions Data sheetPorts and Cabling Port or Connection Port Type, Color1 Cable OL-27644-01 Performing the Initial Configuration on the Router Using Cisco Setup Command Facility You are now in the Setup Configuration Utility Router when it is booted into Cisco IOS-XETo proceed using the setup command facility, enter yes Basic management setup configures only enough connectivity Following configuration command script was created Summary of the available interfaces is displayed Completing the Configuration User prompt is displayed Press Return to bring up the Router prompt Using Cisco IOS-XE CLI-Manual ConfigurationType enable to enter privileged Exec mode Example Configuring the Router HostnameCommand or Action Purpose Configuring the Enable and Enable Secret Passwords Configuring the Console Idle Privileged Exec Timeout Gigabit Ethernet Management Interface Overview Gigabit Ethernet Port Numbering Default Gigabit Ethernet ConfigurationConfiguring Gigabit Ethernet Interfaces Configuration mode Optional Adds a description to an interface configurationDescription helps you remember what is attached to Troubleshooting Configuration Examples Specifying a Default Route or Gateway of Last ResortConfiguring IP Routing and IP Protocols Configuring the GigabitEthernet Interface Example Gateway of Last Resort Default RoutesDefault Network Enables IP routing Establishes a static route Configuration Examples Starts the line configuration command collection mode for Virtual terminal lines vty for remote console accessMake sure that you configure all vty lines on your Line vty ? command Configuring the Auxiliary Line What to Do Next Enable Configure terminal Line aux Auxiliary line Verifying Network Connectivity Saving Your Router Configuration Saving Backup Copies of Configuration and System Image Copying the Startup Configuration to a Tftp Server Example Copying from Flash Memory to a Tftp Server Example 2012 Verifying the Initial Configuration Initial Configuration Verifying the Initial Configuration ROM Monitor Overview ROM Monitor Overview and Basic ProceduresEnvironmental Variables and the Configuration Register Entering ROM Monitor Mode Accessing ROM Monitor Mode with a Terminal ConnectionNetwork Management Access and ROM Monitor Mode Checking the Current ROMmon Version XXX-XXXX-XX Commonly Used ROM Monitor Commands Displaying the Available ROM Monitor Commands2describes the available help commands for ROM Monitor mode Examples Changing the ROM Monitor Prompt Displaying the Configuration Register SettingEnvironment Variable Settings Displaying Environment Variable Settings Frequently Used Environmental Variables Exiting ROM Monitor Mode Entering Environment Variable SettingsSaving Environment Variable Settings Respond to each prompt as instructed Resets and initializes the router Configuration ExampleInitiates the configuration register configuration prompts Example of Upgrade Upgrading the ROMmon for a Router Router# show romvar Internal and External Modules FRUs Safety Warnings 1029 T1 SFP Statement Accessing Internal Modules Removing and Replacing the Chassis CoverRemoving the Cover Replacing the Cover Locating Internal and External Slots for Modules Cover screws ISC slot DIMMs NIM-SSD Slot 0 Factory-configuredOverview of the SSD Carrier Card NIM NIM-SSD Overview 3shows the front panel of the SSD NIM LEDs on the NIM-SSD 1describes the LEDs on the NIM-SSD as shown in FigureRepresents Color Description Solid state drive Green SSD present Slot Off No SSD in slot 2lists the specifications of the SSD Carrier Card NIM Power consumption maximum 20WEnvironmental Transportation and Storage Solid State Drives SSD Top View of the SSD Carrier Card NIM with Serial Number Solid State Drive SSD Installing the SSD Drives into the NIM Carrier Card Opening the SSD Slot Cover Removing the SSD Drives from the NIM-SSD Tabs to pull out the SSD drives 10 Pulling out the Solid State Drives Removing and Replacing the Cisco ISR 4451-X NIM-SSD Drives Restrictions Removing the NIM-SSD from the Router 12 Removing the NIM-SSD from the Router Locating and Orienting Dimm Installing and Removing DDR DIMMsReplacing the NIM-SSD on the Router Polarization notch 14 Dimm Showing Polarization Notch Removing a Dimm 15 Removing a Dimm Installing a Dimm 16 Dimm Showing Polarization Notch 17 Handling the DIMMs Installing and Removing NIMs and SMs 18 Installing a Dimm Installing an SM Software Requirement for SMsLocating an SM or NIM Removing an SM or NIM Installing and Removing the PVDM4 Verifying SM Installation Tools and Equipment Required During Installation PVDM4 Location and Orientation Installing the PVDM4 on the Motherboard of the Cisco ISR Any module replacementGround Remove the cover Standoffs Screws ConnectorRemoving the PVDM4 from the Motherboard of the Cisco ISR Captive Screws Ports Network Card 22 Network Interface Module with PVDM4 Removing and Replacing the USB Flash Token Memory Stick Replacing the Cisco ISR 4451-X Power Supply This completes the USB Flash memory installation procedure 24 Power Supply Unit Replacing the Power Supply on the Cisco ISR 4451-Xs Inserting PoE Supply in an Ethernet Switch Network Module Cisco ISR 4451-X Power and RPS Error Messages Replacing a Fan TrayReplacing the Cisco ISR 4451-X Fan Tray Before Hot-Swapping a Fan Tray 26 Cisco ISR 4451-X Fan Tray Replacement Fan Tray Removing and Installing a CompactFlash Memory Card Removing a CompactFlash Memory Card Installing a CompactFlash Memory Card Installing SFP Modules DWDM-SFP-4373 1543.73 DWDM-SFP-44531544.53 DWDM-SFP-4612 1546.12 DWDM-SFP-4692 Connect the network cable to the SFP module Laser Safety GuidelinesRemoving SFP Modules Removing, Replacing, and Installing an Internal PoE Card Disconnect the SFP latch. See Figure 29 Location of the PoE Card Online Insertion and Removal OIR Hot-Swapping Requirement OIR Procedures Hot-Swapping ProceduresRemoving a Module Inserting a Data or Voice Module