Site Environmental Requirements | Cisco Systems ISR4451XK9 instruction

Chapter 2 Preparing for Router Installation

General Site Requirements

The Cisco ISR 4451-Xs are designed to meet the industry EMC, safety, and environmental standards described in the Regulatory, Safety, and Compliance Information for Cisco 4451-X Integrated Services Routers document.

Site Environmental Requirements

Environmental monitoring in the Cisco ISR 4451-X protects the system and components from damage caused by excessive voltage and temperature conditions. To ensure normal operation and avoid unnecessary maintenance, plan and prepare your site configuration before installation. After installation, make sure the site maintains the environmental characteristics as shown in Table 2-1.

Table 2-1	Cisco ISR 4451-X Environmental Tolerances

Environmental Characteristic		Minimum	Maximum

Steady State Operating		0 degree C	50 degree C
			(50 degrees C at 10,000
			feet)

Storage		–20 degrees C	+70 degrees C

Humidity operating (noncondensing)		10%	90%

Humidity nonoperating (noncondensing)		5%	95%

Altitude operating: over allowable temperature		–500 feet	10,000 feet
range (0 to 50 degrees C)

Altitude, nonoperating: over allowable temperature		–1000 feet	50,000 feet
range

Thermal shock non-operating with change over time		–25 degrees C	+70 degrees C
of 3 minute

Thermal Shock - Operating at 2.5 degree C per		0 degrees C	+50 degrees C
minute

Hardware Installation Guide for the Cisco 4451-X Integrated Services Router

	OL-27644-01	2-8

Image 51

Cisco Systems ISR4451XK9 manual Site Environmental Requirements, Environmental Characteristic Minimum Maximum

Contents

Cisco Systems, Inc Page N T E N T S Additional Slots Ports and Cabling Safety Warnings Accessing Internal Modules Installing and Removing NIMs and SMs OIR Procedures Audience Objectives Chapter Title Description Organization Convention Indication Conventions Warnung Wichtige Sicherheitshinweise Bewaar Deze Instructies Aviso Instruções Importantes DE Segurança Avvertenza Importanti Istruzioni Sulla Sicurezza Xiv GEM Disse Anvisninger Xvi Related Documentation Searching for Cisco Documents Obtaining Documentation and Submitting a Service Request About the Cisco ISR Overview of the Cisco 4451-X Integrated Services Router Safety Warnings Chassis Views Safety Warnings for Finland, Norway and Sweden On page 1-4- Bezel view with one PSU Cisco ISR 4451-X Chassis Bezel side of the Cisco ISR 4451-X with two PSUs Bezel Side Leds of the Single PSU Cisco ISR 4451-X Model ISC slot Modular HDD Slot Factory-configuredLocating the Serial Number, PID, VID and Clei Platform Summary Product ID Labels on Cisco ISRFor Additional Help Locating Labels on the Router Label Description Built-in Interface Ports Hardware Features Front Panel PoE+ Ports Dual Mode GE/SFP PortsFront Panel Ethernet Ports USB Serial Console Port LED Indicators Internal PoE cardRepresents Color Description Location Status Green Tbd Side Ports 0, 1 Amber Off Not present Console Active Right Will be offActive Left Will be off Two PoE PSUs installed and operating Redundant mode Removable and Interchangeable Modules and CardsExternal Slots Internal Slots Network Interface Modules Cisco UCS E-Series Server Modules Compact FlashSolid State Drives Packet Voice Digital Signal Processor Modules Power SuppliesMemory This section covers the following topics About Slots and InterfacesFans, Ventilation, and Airflow About Slot, Subslot Bay, and Port Numbering 9shows the ports and slots on the Cisco ISR 4451-Xs Tuple Example Slot Bay Port Slots are numbered 0, 1 Slot NumberingAbout Slot Console port About Fixed Interfaces SpecificationsSubslot/Bay Numbering Gigabit Ethernet Management Ports Description SpecificationPower Is disabled. See xxxx for a list of supported modules Description Specification Regulatory For detailed compliance information, see the Regulatory Integrated Services Router document Periodic Inspection and Cleaning Standard Warning Statements General Safety WarningsPage Page Page Safety Recommendations Safety with ElectricityFollow these guidelines to ensure general safety Preparing for Router Installation Safety Recommendations Site Selection Guidelines General PrecautionsGeneral Site Requirements Preventing Electrostatic Discharge Damage Site Environmental Requirements Environmental Characteristic Minimum Maximum Rack Requirements Physical CharacteristicsCharacteristics Height Width Depth Weight Router Environmental Requirements Network Cabling Specifications Power Guidelines and Requirements Console Port Connections Console and Auxiliary Port Considerations USB Console OS Compatibility Auxiliary Port Connections Ethernet Connections Preparing for Network Connections OL-27644-01 Task Verified by Date Installation Checklist Creating a Site Log Installing and Connecting the Router Page Slot and Port Numbers CLI Console AccessWhat You Need to Know Before You Begin Unpacking the Router Installing the Router Rack-Mounting the Chassis Attaching Rack-Mount BracketsStatement Inch SBC brackets Inch EIA brackets Inch SBC 1 brackets Inch EIA brackets Mounting the Router in a Rack Bracket Installation for Back Mounting 5shows a typical installation in a rack Mounting screws Grounding the Chassis Setting the Chassis on a Desktop Chassis Grounding Chassis Ground Connection on the Cisco ISR 4451-X Chassis Connecting Power 15A, 120VAC 16A, 240VAC. Statement Connecting to AC Power Serial RJ-45 EIA RJ-45 Connecting to a Console Terminal or ModemConnecting to the Serial Port with Microsoft Windows Port Type Cable Section No parity Stop bit No flow control Connecting to the Console Port with Mac OS To disconnect the OS X USB console from the Terminal window Connecting to the Console Port with Linux Installing the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows 2000 USB DriverInstalling the Cisco Microsoft Windows Vista USB Driver Uninstalling the Cisco Microsoft Windows USB Driver Using the Add Remove Programs utilityUsing the Setup.exe program Uninstalling the Cisco Microsoft Windows Vista USB Driver Connecting to the Auxiliary Port Connecting a Modem to the Cisco ISR Connecting WAN, LAN, and Voice Interfaces OL-27644-01 Port or Connection Port Type, Color1 Cable Connection Procedures and PrecautionsData sheet Ports and Cabling OL-27644-01 Using Cisco Setup Command Facility Performing the Initial Configuration on the Router Basic management setup configures only enough connectivity You are now in the Setup Configuration UtilityRouter when it is booted into Cisco IOS-XE To proceed using the setup command facility, enter yes Summary of the available interfaces is displayed Following configuration command script was created User prompt is displayed Completing the Configuration Using Cisco IOS-XE CLI-Manual Configuration Type enable to enter privileged Exec modePress Return to bring up the Router prompt Configuring the Router Hostname Command or Action PurposeExample Configuring the Enable and Enable Secret Passwords Configuring the Console Idle Privileged Exec Timeout Gigabit Ethernet Management Interface Overview Default Gigabit Ethernet Configuration Configuring Gigabit Ethernet InterfacesGigabit Ethernet Port Numbering Troubleshooting Configuration modeOptional Adds a description to an interface configuration Description helps you remember what is attached to Configuring the GigabitEthernet Interface Example Configuration ExamplesSpecifying a Default Route or Gateway of Last Resort Configuring IP Routing and IP Protocols Default Routes Default NetworkGateway of Last Resort Establishes a static route Enables IP routing Configuration Examples Line vty ? command Starts the line configuration command collection mode forVirtual terminal lines vty for remote console access Make sure that you configure all vty lines on your What to Do Next Configuring the Auxiliary Line Auxiliary line Enable Configure terminal Line aux Verifying Network Connectivity Saving Backup Copies of Configuration and System Image Saving Your Router Configuration Copying from Flash Memory to a Tftp Server Example Copying the Startup Configuration to a Tftp Server Example 2012 Initial Configuration Verifying the Initial Configuration Verifying the Initial Configuration ROM Monitor Overview and Basic Procedures Environmental Variables and the Configuration RegisterROM Monitor Overview Checking the Current ROMmon Version Entering ROM Monitor ModeAccessing ROM Monitor Mode with a Terminal Connection Network Management Access and ROM Monitor Mode XXX-XXXX-XX Examples Commonly Used ROM Monitor CommandsDisplaying the Available ROM Monitor Commands 2describes the available help commands for ROM Monitor mode Displaying the Configuration Register Setting Environment Variable SettingsChanging the ROM Monitor Prompt Frequently Used Environmental Variables Displaying Environment Variable Settings Respond to each prompt as instructed Exiting ROM Monitor ModeEntering Environment Variable Settings Saving Environment Variable Settings Configuration Example Initiates the configuration register configuration promptsResets and initializes the router Upgrading the ROMmon for a Router Example of Upgrade Router# show romvar FRUs Internal and External Modules Safety Warnings 1029 T1 SFP Statement Replacing the Cover Accessing Internal ModulesRemoving and Replacing the Chassis Cover Removing the Cover Cover screws Locating Internal and External Slots for Modules NIM-SSD Slot 0 Factory-configured Overview of the SSD Carrier Card NIM NIM-SSDISC slot DIMMs 3shows the front panel of the SSD NIM Overview Solid state drive Green SSD present Slot Off No SSD in slot LEDs on the NIM-SSD1describes the LEDs on the NIM-SSD as shown in Figure Represents Color Description Transportation and Storage 2lists the specifications of the SSD Carrier Card NIMPower consumption maximum 20W Environmental Top View of the SSD Carrier Card NIM with Serial Number Solid State Drives SSD Solid State Drive SSD Opening the SSD Slot Cover Installing the SSD Drives into the NIM Carrier Card Removing the SSD Drives from the NIM-SSD 10 Pulling out the Solid State Drives Tabs to pull out the SSD drives Restrictions Removing and Replacing the Cisco ISR 4451-X NIM-SSD Drives Removing the NIM-SSD from the Router 12 Removing the NIM-SSD from the Router Installing and Removing DDR DIMMs Replacing the NIM-SSD on the RouterLocating and Orienting Dimm 14 Dimm Showing Polarization Notch Polarization notch 15 Removing a Dimm Removing a Dimm 16 Dimm Showing Polarization Notch Installing a Dimm 17 Handling the DIMMs 18 Installing a Dimm Installing and Removing NIMs and SMs Removing an SM or NIM Installing an SMSoftware Requirement for SMs Locating an SM or NIM Verifying SM Installation Installing and Removing the PVDM4 PVDM4 Location and Orientation Tools and Equipment Required During Installation Remove the cover Installing the PVDM4 on the Motherboard of the Cisco ISRAny module replacement Ground Screws Connector Removing the PVDM4 from the Motherboard of the Cisco ISRStandoffs 22 Network Interface Module with PVDM4 Captive Screws Ports Network Card Removing and Replacing the USB Flash Token Memory Stick This completes the USB Flash memory installation procedure Replacing the Cisco ISR 4451-X Power Supply 24 Power Supply Unit Inserting PoE Supply in an Ethernet Switch Network Module Replacing the Power Supply on the Cisco ISR 4451-Xs Before Hot-Swapping a Fan Tray Cisco ISR 4451-X Power and RPS Error MessagesReplacing a Fan Tray Replacing the Cisco ISR 4451-X Fan Tray Fan Tray 26 Cisco ISR 4451-X Fan Tray Replacement Removing a CompactFlash Memory Card Removing and Installing a CompactFlash Memory Card Installing a CompactFlash Memory Card Installing SFP Modules 1546.12 DWDM-SFP-4692 DWDM-SFP-43731543.73 DWDM-SFP-4453 1544.53 DWDM-SFP-4612 Laser Safety Guidelines Removing SFP ModulesConnect the network cable to the SFP module Disconnect the SFP latch. See Figure Removing, Replacing, and Installing an Internal PoE Card 29 Location of the PoE Card Requirement Online Insertion and Removal OIR Hot-Swapping Inserting a Data or Voice Module OIR ProceduresHot-Swapping Procedures Removing a Module