Regulatory | Cisco Systems ISR4451XK9 instruction

Chapter 1 Overview of the Cisco 4451-X Integrated Services Router

Specifications

Table 1-5 Cisco ISR 4451-X Router Specifications (continued)

Description	Specification

Acoustic: Sound Pressure	54.4 to 67.4 dBA
(Typical/Maximum)

Acoustic: Sound Power	62.6 to 74.5 dBA
(Typical/Maximum)

Regulatory

Safety compliance

IEC 60950-1, Safety of information technology equipment

EN 60950-1, Safety of information technology equipment

UL 60950-1, Standard for safety for information technology equipment [US]

CAN/CSA C22.2 No. 60950-1, Safety of information technology equipment including electrical business equipment [Canada]

AS/NZS 60950.1 2003

GB 4943[PRC]

IEC60950, 2nd Edition [Mexico]

For detailed compliance information, see the Regulatory Compliance and Safety Information for the Cisco 4451-X Integrated Services Router document

		Hardware Installation Guide for the Cisco 4451-X Integrated Services Router

	OL-27644-01			1-23
	OL-27644-01			1-23

Image 41

Cisco Systems ISR4451XK9 manual Regulatory

Contents

Cisco Systems, Inc Page N T E N T S Additional Slots Ports and Cabling Safety Warnings Accessing Internal Modules Installing and Removing NIMs and SMs OIR Procedures Audience Objectives Chapter Title Description Organization Convention Indication Conventions Warnung Wichtige Sicherheitshinweise Bewaar Deze Instructies Aviso Instruções Importantes DE Segurança Avvertenza Importanti Istruzioni Sulla Sicurezza Xiv GEM Disse Anvisninger Xvi Related Documentation Searching for Cisco Documents Obtaining Documentation and Submitting a Service Request About the Cisco ISR Overview of the Cisco 4451-X Integrated Services Router Safety Warnings Chassis Views Safety Warnings for Finland, Norway and Sweden On page 1-4- Bezel view with one PSU Cisco ISR 4451-X Chassis Bezel side of the Cisco ISR 4451-X with two PSUs Bezel Side Leds of the Single PSU Cisco ISR 4451-X Model Locating the Serial Number, PID, VID and Clei Modular HDD Slot Factory-configuredPlatform Summary ISC slot For Additional Help Locating Labels on the Router Labels on Cisco ISRLabel Description Product ID Built-in Interface Ports Hardware Features Front Panel Ethernet Ports Dual Mode GE/SFP PortsUSB Serial Console Port Front Panel PoE+ Ports Represents Color Description Location LED IndicatorsInternal PoE card Active Left Will be off Status Green Tbd Side Ports 0, 1 Amber Off Not presentConsole Active Right Will be off External Slots Two PoE PSUs installed and operating Redundant modeRemovable and Interchangeable Modules and Cards Internal Slots Solid State Drives Network Interface Modules Cisco UCS E-Series Server ModulesCompact Flash Memory Packet Voice Digital Signal Processor ModulesPower Supplies Fans, Ventilation, and Airflow About Slots and InterfacesAbout Slot, Subslot Bay, and Port Numbering This section covers the following topics 9shows the ports and slots on the Cisco ISR 4451-Xs Tuple Example Slot Bay Port About Slot Slot NumberingConsole port Slots are numbered 0, 1 Subslot/Bay Numbering SpecificationsGigabit Ethernet Management About Fixed Interfaces Power Description SpecificationIs disabled. See xxxx for a list of supported modules Ports Description Specification Regulatory For detailed compliance information, see the Regulatory Integrated Services Router document Periodic Inspection and Cleaning Standard Warning Statements General Safety WarningsPage Page Page Follow these guidelines to ensure general safety Safety RecommendationsSafety with Electricity Preparing for Router Installation Safety Recommendations General Site Requirements General PrecautionsPreventing Electrostatic Discharge Damage Site Selection Guidelines Site Environmental Requirements Environmental Characteristic Minimum Maximum Characteristics Physical CharacteristicsHeight Width Depth Weight Rack Requirements Router Environmental Requirements Network Cabling Specifications Power Guidelines and Requirements Console Port Connections Console and Auxiliary Port Considerations USB Console OS Compatibility Auxiliary Port Connections Ethernet Connections Preparing for Network Connections OL-27644-01 Task Verified by Date Installation Checklist Creating a Site Log Installing and Connecting the Router Page What You Need to Know CLI Console AccessBefore You Begin Slot and Port Numbers Unpacking the Router Installing the Router Statement Rack-Mounting the ChassisAttaching Rack-Mount Brackets Inch SBC brackets Inch EIA brackets Inch SBC 1 brackets Inch EIA brackets Mounting the Router in a Rack Bracket Installation for Back Mounting 5shows a typical installation in a rack Mounting screws Grounding the Chassis Setting the Chassis on a Desktop Chassis Grounding Chassis Ground Connection on the Cisco ISR 4451-X Chassis Connecting Power 15A, 120VAC 16A, 240VAC. Statement Connecting to AC Power Connecting to the Serial Port with Microsoft Windows Connecting to a Console Terminal or ModemPort Type Cable Section Serial RJ-45 EIA RJ-45 No parity Stop bit No flow control Connecting to the Console Port with Mac OS To disconnect the OS X USB console from the Terminal window Connecting to the Console Port with Linux Installing the Cisco Microsoft Windows Vista USB Driver Installing the Cisco Microsoft Windows XP USB DriverInstalling the Cisco Microsoft Windows 2000 USB Driver Using the Setup.exe program Uninstalling the Cisco Microsoft Windows USB DriverUsing the Add Remove Programs utility Uninstalling the Cisco Microsoft Windows Vista USB Driver Connecting to the Auxiliary Port Connecting a Modem to the Cisco ISR Connecting WAN, LAN, and Voice Interfaces OL-27644-01 Data sheet Connection Procedures and PrecautionsPorts and Cabling Port or Connection Port Type, Color1 Cable OL-27644-01 Using Cisco Setup Command Facility Performing the Initial Configuration on the Router Router when it is booted into Cisco IOS-XE You are now in the Setup Configuration UtilityTo proceed using the setup command facility, enter yes Basic management setup configures only enough connectivity Summary of the available interfaces is displayed Following configuration command script was created User prompt is displayed Completing the Configuration Press Return to bring up the Router prompt Using Cisco IOS-XE CLI-Manual ConfigurationType enable to enter privileged Exec mode Example Configuring the Router HostnameCommand or Action Purpose Configuring the Enable and Enable Secret Passwords Configuring the Console Idle Privileged Exec Timeout Gigabit Ethernet Management Interface Overview Gigabit Ethernet Port Numbering Default Gigabit Ethernet ConfigurationConfiguring Gigabit Ethernet Interfaces Optional Adds a description to an interface configuration Configuration modeDescription helps you remember what is attached to Troubleshooting Specifying a Default Route or Gateway of Last Resort Configuration ExamplesConfiguring IP Routing and IP Protocols Configuring the GigabitEthernet Interface Example Gateway of Last Resort Default RoutesDefault Network Establishes a static route Enables IP routing Configuration Examples Virtual terminal lines vty for remote console access Starts the line configuration command collection mode forMake sure that you configure all vty lines on your Line vty ? command What to Do Next Configuring the Auxiliary Line Auxiliary line Enable Configure terminal Line aux Verifying Network Connectivity Saving Backup Copies of Configuration and System Image Saving Your Router Configuration Copying from Flash Memory to a Tftp Server Example Copying the Startup Configuration to a Tftp Server Example 2012 Initial Configuration Verifying the Initial Configuration Verifying the Initial Configuration ROM Monitor Overview ROM Monitor Overview and Basic ProceduresEnvironmental Variables and the Configuration Register Accessing ROM Monitor Mode with a Terminal Connection Entering ROM Monitor ModeNetwork Management Access and ROM Monitor Mode Checking the Current ROMmon Version XXX-XXXX-XX Displaying the Available ROM Monitor Commands Commonly Used ROM Monitor Commands2describes the available help commands for ROM Monitor mode Examples Changing the ROM Monitor Prompt Displaying the Configuration Register SettingEnvironment Variable Settings Frequently Used Environmental Variables Displaying Environment Variable Settings Entering Environment Variable Settings Exiting ROM Monitor ModeSaving Environment Variable Settings Respond to each prompt as instructed Resets and initializes the router Configuration ExampleInitiates the configuration register configuration prompts Upgrading the ROMmon for a Router Example of Upgrade Router# show romvar FRUs Internal and External Modules Safety Warnings 1029 T1 SFP Statement Removing and Replacing the Chassis Cover Accessing Internal ModulesRemoving the Cover Replacing the Cover Cover screws Locating Internal and External Slots for Modules ISC slot DIMMs NIM-SSD Slot 0 Factory-configuredOverview of the SSD Carrier Card NIM NIM-SSD 3shows the front panel of the SSD NIM Overview 1describes the LEDs on the NIM-SSD as shown in Figure LEDs on the NIM-SSDRepresents Color Description Solid state drive Green SSD present Slot Off No SSD in slot Power consumption maximum 20W 2lists the specifications of the SSD Carrier Card NIMEnvironmental Transportation and Storage Top View of the SSD Carrier Card NIM with Serial Number Solid State Drives SSD Solid State Drive SSD Opening the SSD Slot Cover Installing the SSD Drives into the NIM Carrier Card Removing the SSD Drives from the NIM-SSD 10 Pulling out the Solid State Drives Tabs to pull out the SSD drives Restrictions Removing and Replacing the Cisco ISR 4451-X NIM-SSD Drives Removing the NIM-SSD from the Router 12 Removing the NIM-SSD from the Router Locating and Orienting Dimm Installing and Removing DDR DIMMsReplacing the NIM-SSD on the Router 14 Dimm Showing Polarization Notch Polarization notch 15 Removing a Dimm Removing a Dimm 16 Dimm Showing Polarization Notch Installing a Dimm 17 Handling the DIMMs 18 Installing a Dimm Installing and Removing NIMs and SMs Software Requirement for SMs Installing an SMLocating an SM or NIM Removing an SM or NIM Verifying SM Installation Installing and Removing the PVDM4 PVDM4 Location and Orientation Tools and Equipment Required During Installation Any module replacement Installing the PVDM4 on the Motherboard of the Cisco ISRGround Remove the cover Standoffs Screws ConnectorRemoving the PVDM4 from the Motherboard of the Cisco ISR 22 Network Interface Module with PVDM4 Captive Screws Ports Network Card Removing and Replacing the USB Flash Token Memory Stick This completes the USB Flash memory installation procedure Replacing the Cisco ISR 4451-X Power Supply 24 Power Supply Unit Inserting PoE Supply in an Ethernet Switch Network Module Replacing the Power Supply on the Cisco ISR 4451-Xs Replacing a Fan Tray Cisco ISR 4451-X Power and RPS Error MessagesReplacing the Cisco ISR 4451-X Fan Tray Before Hot-Swapping a Fan Tray Fan Tray 26 Cisco ISR 4451-X Fan Tray Replacement Removing a CompactFlash Memory Card Removing and Installing a CompactFlash Memory Card Installing a CompactFlash Memory Card Installing SFP Modules 1543.73 DWDM-SFP-4453 DWDM-SFP-43731544.53 DWDM-SFP-4612 1546.12 DWDM-SFP-4692 Connect the network cable to the SFP module Laser Safety GuidelinesRemoving SFP Modules Disconnect the SFP latch. See Figure Removing, Replacing, and Installing an Internal PoE Card 29 Location of the PoE Card Requirement Online Insertion and Removal OIR Hot-Swapping Hot-Swapping Procedures OIR ProceduresRemoving a Module Inserting a Data or Voice Module