Installing SFP Modules | Cisco Systems ISR4451XK9 guide

Chapter 6 Installing and Upgrading Internal Modules and FRUs

Installing SFP Modules

Installing SFP Modules

This section describes how to install optional small-form-factor pluggable (SFP) modules in

Cisco ISR 4451-Xs to provide optical Gigabit Ethernet connectivity. There are four SFP slots in the Cisco ISR 4451-X.

The SFP module installs into a slot on the router rear panel. When selected in Cisco IOS software, it is assigned port gigabitethernet 0/0/0. The default is the built-in RJ-45 1000Base-T connector, which is enabled on this port.

Only SFP modules certified by Cisco are supported on Cisco ISR 4451-Xs. Table 6-3lists supported SFPs on Cisco ISR 4451-Xs.

See Cisco Transceiver Modules Compatibility Information for compatibility issues.

		Table 6-3	SFPs Supported on Cisco ISR 4451-Xs

					Fiber Diameter	Wavelength		Maximum
		Cisco Model Number		SFP Transceiver	(micrometer)	(nm)	Mode	Distance

		GLC-SX-MM=		1000Base-SX	50	850	Multi	550 m

		GLC-LH-SM=		1000Base-LX/LH	9/125	1310	Single	10 km

		GLC-ZX-SM=		1000Base-ZX	9/125	1550	Single	100 km

		CWDM-SFP-1470=		1000Base-CWDM	50	1470	Single	100 km

		CWDM-SFP-1490=				1490

		CWDM-SFP-1510=				1510

		CWDM-SFP-1530=				1530

		CWDM-SFP-1550=				1550

		CWDM-SFP-1570=				1570

		CWDM-SFP-1590=				1590

		CWDM-SFP-1610=				1610

		DWDM-SFP-3033		1000BASE-DWDM	—	1530.33	—			—

		DWDM-SFP-3112		1000BASE-DWDM	—	1531.12	—			—

		DWDM-SFP-3190		1000BASE-DWDM	—	1531.90	—			—

		DWDM-SFP-3268		1000BASE-DWDM	—	1532.68	—			—

		DWDM-SFP-3425		1000BASE-DWDM	—	1534.25	—			—

		DWDM-SFP-3504		1000BASE-DWDM	—	1535.04	—			—

		DWDM-SFP-3582		1000BASE-DWDM	—	1535.82	—			—

		DWDM-SFP-3661		1000BASE-DWDM	—	1536.61	—			—

		DWDM-SFP-3819		1000BASE-DWDM	—	1538.19	—			—

		DWDM-SFP-3898		1000BASE-DWDM	—	1539.77	—			—

		DWDM-SFP-3977		1000BASE-DWDM	—	1539.98	—			—

		DWDM-SFP-4056		1000BASE-DWDM	—	1540.56	—			—

		DWDM-SFP-4214		1000BASE-DWDM	—	1542.14	—			—

		DWDM-SFP-4294		1000BASE-DWDM	—	1542.94	—			—

				Hardware Installation Guide for the Cisco 4451-X Integrated Services Router


	OL-27644-01									6-38
	OL-27644-01									6-38

Image 154

Cisco Systems ISR4451XK9 manual Installing SFP Modules

Contents

Cisco Systems, Inc Page N T E N T S Additional Slots Ports and Cabling Safety Warnings Accessing Internal Modules Installing and Removing NIMs and SMs OIR Procedures Objectives Audience Organization Chapter Title Description Conventions Convention Indication Bewaar Deze Instructies Warnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla Sicurezza Aviso Instruções Importantes DE Segurança Xiv GEM Disse Anvisninger Xvi Related Documentation Obtaining Documentation and Submitting a Service Request Searching for Cisco Documents Overview of the Cisco 4451-X Integrated Services Router About the Cisco ISR Safety Warnings Safety Warnings for Finland, Norway and Sweden Chassis Views Cisco ISR 4451-X Chassis On page 1-4- Bezel view with one PSU Bezel side of the Cisco ISR 4451-X with two PSUs Bezel Side Leds of the Single PSU Cisco ISR 4451-X Model Platform Summary Modular HDD Slot Factory-configuredLocating the Serial Number, PID, VID and Clei ISC slot Label Description Labels on Cisco ISRFor Additional Help Locating Labels on the Router Product ID Hardware Features Built-in Interface Ports USB Serial Console Port Dual Mode GE/SFP PortsFront Panel Ethernet Ports Front Panel PoE+ Ports Internal PoE card LED IndicatorsRepresents Color Description Location Console Active Right Will be off Status Green Tbd Side Ports 0, 1 Amber Off Not presentActive Left Will be off Removable and Interchangeable Modules and Cards Two PoE PSUs installed and operating Redundant modeExternal Slots Internal Slots Compact Flash Network Interface Modules Cisco UCS E-Series Server ModulesSolid State Drives Power Supplies Packet Voice Digital Signal Processor ModulesMemory About Slot, Subslot Bay, and Port Numbering About Slots and InterfacesFans, Ventilation, and Airflow This section covers the following topics Tuple Example Slot Bay Port 9shows the ports and slots on the Cisco ISR 4451-Xs Console port Slot NumberingAbout Slot Slots are numbered 0, 1 Gigabit Ethernet Management SpecificationsSubslot/Bay Numbering About Fixed Interfaces Is disabled. See xxxx for a list of supported modules Description SpecificationPower Ports Description Specification Regulatory Integrated Services Router document For detailed compliance information, see the Regulatory Periodic Inspection and Cleaning General Safety Warnings Standard Warning StatementsPage Page Page Safety with Electricity Safety RecommendationsFollow these guidelines to ensure general safety Preparing for Router Installation Safety Recommendations Preventing Electrostatic Discharge Damage General PrecautionsGeneral Site Requirements Site Selection Guidelines Environmental Characteristic Minimum Maximum Site Environmental Requirements Height Width Depth Weight Physical CharacteristicsCharacteristics Rack Requirements Router Environmental Requirements Power Guidelines and Requirements Network Cabling Specifications Console and Auxiliary Port Considerations Console Port Connections Auxiliary Port Connections USB Console OS Compatibility Preparing for Network Connections Ethernet Connections OL-27644-01 Installation Checklist Task Verified by Date Creating a Site Log Installing and Connecting the Router Page Before You Begin CLI Console AccessWhat You Need to Know Slot and Port Numbers Installing the Router Unpacking the Router Attaching Rack-Mount Brackets Rack-Mounting the ChassisStatement Inch SBC 1 brackets Inch EIA brackets Inch SBC brackets Inch EIA brackets Bracket Installation for Back Mounting Mounting the Router in a Rack 5shows a typical installation in a rack Grounding the Chassis Mounting screws Setting the Chassis on a Desktop Chassis Grounding Connecting Power Chassis Ground Connection on the Cisco ISR 4451-X Chassis Connecting to AC Power 15A, 120VAC 16A, 240VAC. Statement Port Type Cable Section Connecting to a Console Terminal or ModemConnecting to the Serial Port with Microsoft Windows Serial RJ-45 EIA RJ-45 Connecting to the Console Port with Mac OS No parity Stop bit No flow control Connecting to the Console Port with Linux To disconnect the OS X USB console from the Terminal window Installing the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows XP USB DriverInstalling the Cisco Microsoft Windows Vista USB Driver Using the Add Remove Programs utility Uninstalling the Cisco Microsoft Windows USB DriverUsing the Setup.exe program Connecting to the Auxiliary Port Uninstalling the Cisco Microsoft Windows Vista USB Driver Connecting WAN, LAN, and Voice Interfaces Connecting a Modem to the Cisco ISR OL-27644-01 Ports and Cabling Connection Procedures and PrecautionsData sheet Port or Connection Port Type, Color1 Cable OL-27644-01 Performing the Initial Configuration on the Router Using Cisco Setup Command Facility To proceed using the setup command facility, enter yes You are now in the Setup Configuration UtilityRouter when it is booted into Cisco IOS-XE Basic management setup configures only enough connectivity Following configuration command script was created Summary of the available interfaces is displayed Completing the Configuration User prompt is displayed Type enable to enter privileged Exec mode Using Cisco IOS-XE CLI-Manual ConfigurationPress Return to bring up the Router prompt Command or Action Purpose Configuring the Router HostnameExample Configuring the Enable and Enable Secret Passwords Configuring the Console Idle Privileged Exec Timeout Gigabit Ethernet Management Interface Overview Configuring Gigabit Ethernet Interfaces Default Gigabit Ethernet ConfigurationGigabit Ethernet Port Numbering Description helps you remember what is attached to Configuration modeOptional Adds a description to an interface configuration Troubleshooting Configuring IP Routing and IP Protocols Configuration ExamplesSpecifying a Default Route or Gateway of Last Resort Configuring the GigabitEthernet Interface Example Default Network Default RoutesGateway of Last Resort Enables IP routing Establishes a static route Configuration Examples Make sure that you configure all vty lines on your Starts the line configuration command collection mode forVirtual terminal lines vty for remote console access Line vty ? command Configuring the Auxiliary Line What to Do Next Enable Configure terminal Line aux Auxiliary line Verifying Network Connectivity Saving Your Router Configuration Saving Backup Copies of Configuration and System Image Copying the Startup Configuration to a Tftp Server Example Copying from Flash Memory to a Tftp Server Example 2012 Verifying the Initial Configuration Initial Configuration Verifying the Initial Configuration Environmental Variables and the Configuration Register ROM Monitor Overview and Basic ProceduresROM Monitor Overview Network Management Access and ROM Monitor Mode Entering ROM Monitor ModeAccessing ROM Monitor Mode with a Terminal Connection Checking the Current ROMmon Version XXX-XXXX-XX 2describes the available help commands for ROM Monitor mode Commonly Used ROM Monitor CommandsDisplaying the Available ROM Monitor Commands Examples Environment Variable Settings Displaying the Configuration Register SettingChanging the ROM Monitor Prompt Displaying Environment Variable Settings Frequently Used Environmental Variables Saving Environment Variable Settings Exiting ROM Monitor ModeEntering Environment Variable Settings Respond to each prompt as instructed Initiates the configuration register configuration prompts Configuration ExampleResets and initializes the router Example of Upgrade Upgrading the ROMmon for a Router Router# show romvar Internal and External Modules FRUs Safety Warnings 1029 T1 SFP Statement Removing the Cover Accessing Internal ModulesRemoving and Replacing the Chassis Cover Replacing the Cover Locating Internal and External Slots for Modules Cover screws Overview of the SSD Carrier Card NIM NIM-SSD NIM-SSD Slot 0 Factory-configuredISC slot DIMMs Overview 3shows the front panel of the SSD NIM Represents Color Description LEDs on the NIM-SSD1describes the LEDs on the NIM-SSD as shown in Figure Solid state drive Green SSD present Slot Off No SSD in slot Environmental 2lists the specifications of the SSD Carrier Card NIMPower consumption maximum 20W Transportation and Storage Solid State Drives SSD Top View of the SSD Carrier Card NIM with Serial Number Solid State Drive SSD Installing the SSD Drives into the NIM Carrier Card Opening the SSD Slot Cover Removing the SSD Drives from the NIM-SSD Tabs to pull out the SSD drives 10 Pulling out the Solid State Drives Removing and Replacing the Cisco ISR 4451-X NIM-SSD Drives Restrictions Removing the NIM-SSD from the Router 12 Removing the NIM-SSD from the Router Replacing the NIM-SSD on the Router Installing and Removing DDR DIMMsLocating and Orienting Dimm Polarization notch 14 Dimm Showing Polarization Notch Removing a Dimm 15 Removing a Dimm Installing a Dimm 16 Dimm Showing Polarization Notch 17 Handling the DIMMs Installing and Removing NIMs and SMs 18 Installing a Dimm Locating an SM or NIM Installing an SMSoftware Requirement for SMs Removing an SM or NIM Installing and Removing the PVDM4 Verifying SM Installation Tools and Equipment Required During Installation PVDM4 Location and Orientation Ground Installing the PVDM4 on the Motherboard of the Cisco ISRAny module replacement Remove the cover Removing the PVDM4 from the Motherboard of the Cisco ISR Screws ConnectorStandoffs Captive Screws Ports Network Card 22 Network Interface Module with PVDM4 Removing and Replacing the USB Flash Token Memory Stick Replacing the Cisco ISR 4451-X Power Supply This completes the USB Flash memory installation procedure 24 Power Supply Unit Replacing the Power Supply on the Cisco ISR 4451-Xs Inserting PoE Supply in an Ethernet Switch Network Module Replacing the Cisco ISR 4451-X Fan Tray Cisco ISR 4451-X Power and RPS Error MessagesReplacing a Fan Tray Before Hot-Swapping a Fan Tray 26 Cisco ISR 4451-X Fan Tray Replacement Fan Tray Removing and Installing a CompactFlash Memory Card Removing a CompactFlash Memory Card Installing a CompactFlash Memory Card Installing SFP Modules 1544.53 DWDM-SFP-4612 DWDM-SFP-43731543.73 DWDM-SFP-4453 1546.12 DWDM-SFP-4692 Removing SFP Modules Laser Safety GuidelinesConnect the network cable to the SFP module Removing, Replacing, and Installing an Internal PoE Card Disconnect the SFP latch. See Figure 29 Location of the PoE Card Online Insertion and Removal OIR Hot-Swapping Requirement Removing a Module OIR ProceduresHot-Swapping Procedures Inserting a Data or Voice Module