Cisco Systems Linksys PAP2, RT31P2 4.3. Basic Networking Configuration

Protect IVR Factory

Reset Bool No

Admin Password The password for administrator Str63

User Password The password for User Str63

4.3. Basic Networking Configuration

Configuration parameters in this list are used for setting up basic network connectivity. In general,

many of these parameters are set automatically (for example, using DHCP) or are configured by the

end user of the device.

Note that the RT31P2 ignores the following parameters: DHCP, Static_IP, NetMask, and Gateway.

Other than the DNS_Server_Order and DNS_Query_Mode, the rest these parameters also can be

configured from the RT31P2 User GUI.

Network Configuration

Parameter Name Description Type Default

DHCP Enable/Disable DHCP Bool Yes

Host Name Host Name of PHONE ADAPTER Str31

Domain The network domain of PHONE ADAPTER Str127

Static IP Static IP address of PHONE ADAPTER, which will take

effect if DHCP is disabled IP 0.0.0.0

NetMask The NetMask used by PHONE ADAPTER when DHCP

is disabled IP 255.255.255.

0

Gateway The default gateway used by PHONE ADAPTER when

DHCP is disabled IP 0.0.0.0

Primary DNS DNS server used by PHONE ADAPTER in addition to

DHCP supplied DNS servers if DHCP is enabled; when

DHCP is disabled, this will be the primary DNS server.

IP 0.0.0.0

Secondary DNS DNS server used by PHONE ADAPTER in addition to

DHCP supplied DNS servers if DHCP is enabled; when

DHCP is disabled, this will be the secondary DNS

server.

IP 0.0.0.0

DNS Query Mode Do parallel or sequential DNS Query Choice Parallel

Syslog Server Specify the Syslog server name and port. This feature

specifies the server for logging PHONE ADAPTER

system information and critical events.

FQDN

Debug Server The debug server name and port. This feature

specifies the server for logging PHONE ADAPTER

debug information. The level of detailed output

depends on the debug level parameter setting.

FQDN

Debug Level The higher the debug level, the more debug

information will be generated. Zero (0) means no

debug information will be generated.

Choice 0

Primary NTP

Server IP address or name of primary NTP server. Str127

or IP

Secondary NTP

Server IP address or name of secondary NTP server Str127

or IP

Notes:

© 2004 Linksys Proprietary (See Copyright Notice on Page 2)

47

Contents

Main Linksys PAP2 and RT31P2 Disclaimer Please Read: Use of Proprietary Information and Copyright Notice: Page Page Page 1. Introduction 1.1. The Session Initiation Protocol Page 1.1.1. Components of a SIP Network Service Provider Domain Subscriber Domain IP Network (Internet) 1.1.2. Provisioning Overview 1.1.3. Security Overview 1.1.4. SIP Services Page Page Page 1.2. Network Address Translation (NAT) Traversal 1.2.1. What is a NAT or NAPT (Network Address Port Translator)? 1.2.2. VoIP-NAT Interworking 1.3. Voice Quality Overview 2. Hardware Overview Page 2.1. Phone Adapter LED Status 2.2. Broadband Router (RT31P2) LED Status 3. Software Configuration Mechanisms 3.1. Configuration Profile Formats Page 3.1.1. Using the Supplemental Profile Compiler 3.1.2. Encrypting and Compressing XML configuration files 3.2. Secure Initial Configuration 3.3. Web Interface 3.3.1. Web Interface Conventions 3.3.2. Administration Privileges 3.3.3. Basic and Advanced Views 3.4.1. Upgrade URL 3.4.2. Resync URL 3.4.3. Reboot URL 3.4.4. Factory Reset URL 3.5. Configuration via the IVR (PAP2 only) Page Page 4. Configuration Parameters 4.1. Data Types Page 2004 Linksys Proprietary (See Copyright Notice on Page 2) 4.1.1. Conventions 4.2. Provisioning Related Parameters Page Page Page Page Page Page Page 4.2.1. Firmware Upgrade Page Page 4.2.2. Provisioning Server Redundancy 4.2.3. Configuring the Web Server and IVR 4.3. Basic Networking Configuration 4.4. Basic Account Configuration 4.5. Configuration for NAT Traversal Page 4.6. Media and SDP (Session Description Protocol) Configuration 4.6.1. DTMF and Hookflash 4.6.2. Codec and Audio Settings 4.6.3. Dynamic Payload Types and SDP Codec Names 4.6.4. Secure Media Implementation: Page 4.6.5. Outbound Call Codec Selection Codes: 4.7. Supplementary Services 4.7.1. Supplementary Services activated internally Page 4.7.2. Call Forwarding Implemented internally 4.7.3. Supplementary Services implemented in the service provider network 4.8. Dial Plan Configuration Page Page Page Page 4.8.1. Speed Dialing Settings 4.9. Progress Tone and Ring Configuration 4.9.1. Distinctive Ring and Other Ring Settings Page 4.9.2. Progress Tones 4.10. Less Frequently Used Paramters Page Page 4.10.2. Additional User Account Information Page 4.10.3. Per-Line Polarity Settings 4.10.4. Additional Timer Values (sec) 4.10.5. Miscellaneous Parameters Page Figure: PHONE ADAPTER Caller ID Delivery Architecture 5. Expected Feature Behavior 5.1. Originating a Phone Call 5.2. Receiving a Phone Call 5.3. Caller ID 5.4. Calling Line Identification Presentation (CLIP) 5.5. Calling Line Identification Restriction (CLIR) Caller ID Blocking 5.6. Call Waiting 5.7. Disable or Cancel Call Waiting 5.8. Call-Waiting with Caller ID 5.9. Voice Mail 5.10. Attendant Call Transfer 5.11. Unattended or Blind Call Transfer 5.12. Call Hold 5.13. Three-Way Calling 5.14. Three-Way Ad-Hoc Conference Calling 5.15. Call Return 5.16. Automatic Call Back 5.17. Call FWD Unconditional 5.18. Call FWD Busy 5.19. Call FWD - No Answer 5.20. Anonymous Call Blocking 5.21. Distinctive / Priority Ringing and Call Waiting Tone 5.22. Speed Calling Up to Eight (8) Numbers or IP Addresses 6. Troubleshooting 6.1. Call Statistics Reporting 6.2. Enabling Logging and Debugging 6.3. Error and Log Reporting 6.4. Internal Error Codes 6.5. Provisioning and Upgrade result codes 6.6. Table of SIP Response Codes (Error Codes) 7. Summary of Implemented Features and Specifications 7.1. Data Networking Features 7.1.1. MAC Address (IEEE 802.3) 7.2. Voice Features 7.2.3. Secure Calls 7.2.4. Voice Algorithms: 7.2.5. Codec Selection 7.2.6. Dynamic Payload 7.2.7. Adjustable Audio Frames Per Packet 7.2.10. Call Progress Tone Generation 7.2.11. Call Progress Tone Pass Through 7.2.12. Jitter Buffer Dynamic (Adaptive) 7.2.13. Full Duplex Audio 7.2.14. Echo Cancellation Up to 8 ms Echo Tail 7.2.20. Message Waiting Indicator Tones MWI 7.2.21. Polarity Control 7.2.22. Calling Party Control CPC 7.2.23. International Caller ID Delivery 7.2.24. Streaming Audio Server SAS 7.2.25. Music On Hold MOH Page 7.3. Security Features dministration and Maintenance Features ers 7.4. A 8. List of all configuration paramet Page Page Page Page Page Page Page Page Page Page 9. Acronyms Page 10. Glossary