Cisco Systems Linksys PAP2, RT31P2 5.17. Call FWD Unconditional ,

lines are idle, the user hears a special ring.

During the monitoring process the user can

continue to originate and receive calls without

affecting the Call Return on Busy request. Call

Return on Busy requests can be canceled by

dialing the deactivation code.

User Action Required to Deactivate or End Lift the receiver

Listen for dial tone

Press *__

5.17. Call FWD – Unconditional

Service Description All calls are immediately forwarded to the

designated forwarding number. The PHONE

ADAPTER will not ring or provide call waiting

when Call FWD – Unconditional is activated.

User Action Required to Activate or Use Lift the receiver

Listen for dial tone

Press *__

Listen for dial tone and enter the telephone

number you are forwarding your call to.

Activation will be confirmed with three short

bursts of tone and your forwarding will be

activated.

Alternatively, the user can activate this feature

from a web browser interface.

Expected Call and Network Behavior This feature allows a user the option to divert

(forward) all calls to their telephone number to

any number using the touchtone keypad of

their telephone or web browser interface. This

service is activated or deactivated from the

phone being forwarded or the web browser

interface.

User Action Required to Deactivate or End Lift the receiver

Listen for dial tone

Press *__

You will hear a confirmation tone signaling your

change has been accepted.

Alternatively, the user can deactivate this

feature from a web browser interface.

© 2004 Linksys Proprietary (See Copyright Notice on Page 2)

88

Contents

Main Linksys PAP2 and RT31P2 Disclaimer Please Read: Use of Proprietary Information and Copyright Notice: Page Page Page 1. Introduction 1.1. The Session Initiation Protocol Page 1.1.1. Components of a SIP Network Service Provider Domain Subscriber Domain IP Network (Internet) 1.1.2. Provisioning Overview 1.1.3. Security Overview 1.1.4. SIP Services Page Page Page 1.2. Network Address Translation (NAT) Traversal 1.2.1. What is a NAT or NAPT (Network Address Port Translator)? 1.2.2. VoIP-NAT Interworking 1.3. Voice Quality Overview 2. Hardware Overview Page 2.1. Phone Adapter LED Status 2.2. Broadband Router (RT31P2) LED Status 3. Software Configuration Mechanisms 3.1. Configuration Profile Formats Page 3.1.1. Using the Supplemental Profile Compiler 3.1.2. Encrypting and Compressing XML configuration files 3.2. Secure Initial Configuration 3.3. Web Interface 3.3.1. Web Interface Conventions 3.3.2. Administration Privileges 3.3.3. Basic and Advanced Views 3.4.1. Upgrade URL 3.4.2. Resync URL 3.4.3. Reboot URL 3.4.4. Factory Reset URL 3.5. Configuration via the IVR (PAP2 only) Page Page 4. Configuration Parameters 4.1. Data Types Page 2004 Linksys Proprietary (See Copyright Notice on Page 2) 4.1.1. Conventions 4.2. Provisioning Related Parameters Page Page Page Page Page Page Page 4.2.1. Firmware Upgrade Page Page 4.2.2. Provisioning Server Redundancy 4.2.3. Configuring the Web Server and IVR 4.3. Basic Networking Configuration 4.4. Basic Account Configuration 4.5. Configuration for NAT Traversal Page 4.6. Media and SDP (Session Description Protocol) Configuration 4.6.1. DTMF and Hookflash 4.6.2. Codec and Audio Settings 4.6.3. Dynamic Payload Types and SDP Codec Names 4.6.4. Secure Media Implementation: Page 4.6.5. Outbound Call Codec Selection Codes: 4.7. Supplementary Services 4.7.1. Supplementary Services activated internally Page 4.7.2. Call Forwarding Implemented internally 4.7.3. Supplementary Services implemented in the service provider network 4.8. Dial Plan Configuration Page Page Page Page 4.8.1. Speed Dialing Settings 4.9. Progress Tone and Ring Configuration 4.9.1. Distinctive Ring and Other Ring Settings Page 4.9.2. Progress Tones 4.10. Less Frequently Used Paramters Page Page 4.10.2. Additional User Account Information Page 4.10.3. Per-Line Polarity Settings 4.10.4. Additional Timer Values (sec) 4.10.5. Miscellaneous Parameters Page Figure: PHONE ADAPTER Caller ID Delivery Architecture 5. Expected Feature Behavior 5.1. Originating a Phone Call 5.2. Receiving a Phone Call 5.3. Caller ID 5.4. Calling Line Identification Presentation (CLIP) 5.5. Calling Line Identification Restriction (CLIR) Caller ID Blocking 5.6. Call Waiting 5.7. Disable or Cancel Call Waiting 5.8. Call-Waiting with Caller ID 5.9. Voice Mail 5.10. Attendant Call Transfer 5.11. Unattended or Blind Call Transfer 5.12. Call Hold 5.13. Three-Way Calling 5.14. Three-Way Ad-Hoc Conference Calling 5.15. Call Return 5.16. Automatic Call Back 5.17. Call FWD Unconditional 5.18. Call FWD Busy 5.19. Call FWD - No Answer 5.20. Anonymous Call Blocking 5.21. Distinctive / Priority Ringing and Call Waiting Tone 5.22. Speed Calling Up to Eight (8) Numbers or IP Addresses 6. Troubleshooting 6.1. Call Statistics Reporting 6.2. Enabling Logging and Debugging 6.3. Error and Log Reporting 6.4. Internal Error Codes 6.5. Provisioning and Upgrade result codes 6.6. Table of SIP Response Codes (Error Codes) 7. Summary of Implemented Features and Specifications 7.1. Data Networking Features 7.1.1. MAC Address (IEEE 802.3) 7.2. Voice Features 7.2.3. Secure Calls 7.2.4. Voice Algorithms: 7.2.5. Codec Selection 7.2.6. Dynamic Payload 7.2.7. Adjustable Audio Frames Per Packet 7.2.10. Call Progress Tone Generation 7.2.11. Call Progress Tone Pass Through 7.2.12. Jitter Buffer Dynamic (Adaptive) 7.2.13. Full Duplex Audio 7.2.14. Echo Cancellation Up to 8 ms Echo Tail 7.2.20. Message Waiting Indicator Tones MWI 7.2.21. Polarity Control 7.2.22. Calling Party Control CPC 7.2.23. International Caller ID Delivery 7.2.24. Streaming Audio Server SAS 7.2.25. Music On Hold MOH Page 7.3. Security Features dministration and Maintenance Features ers 7.4. A 8. List of all configuration paramet Page Page Page Page Page Page Page Page Page Page 9. Acronyms Page 10. Glossary