Manuals / Brands / Communications / Telephone Accessories / Cisco Systems / Communications / Telephone Accessories

Cisco Systems Linksys PAP2, RT31P2 7. Summary of Implemented Features and Specifications

1 117

Download 117 pages, 1.41 Mb

410 Gone

412 Conditional Request Failed

413 Request Entity Too Large

414 Request-URI Too Long

415 Unsupported Media Type

416 Unsupported URI Scheme

420 Bad Extension

421 Extension Required

423 Interval Too Brief

429 Provide Referrer Identity

480 Temporarily Unavailable

481 Call/Transaction Does Not Exist

482 Loop Detected

483 Too Many Hops

484 Address Incomplete

485 Ambiguous

486 Busy Here

487 Request Terminated

488 Not Acceptable Here

489 Bad Event

491 Request Pending

493 Undecipherable

494 Security Agreement Required

Server Failure 5xx

500 Server Internal Error

501 Not Implemented

502 Bad Gateway

503 Service Unavailable

504 Server Time-out

505 Version Not Supported

513 Message Too Large

580 Precondition Failure

Global Failures 6xx

600 Busy Everywhere

603 Decline

604 Does Not Exist Anywhere

606 Not Acceptable

7. Summary of Implemented Features and Specifications

The PHONE ADAPTER is a full featured, fully programmable phone adapter that can be custom

provisioned within a wide range of configuration parameters. The below feature descriptions are

written as a high-level overview to provide a basic understanding of the feature breadth and

capabilities of the PHONE ADAPTER. To understand the specific implementation of the below

features, including parameters, requirements and contingencies please refer the section PHONE

ADAPTER Feature Configuration Parameters, section Error! Reference source not found..

7.1. Data Networking Features

7.1.1. MAC Address (IEEE 802.3)

© 2004 Linksys Proprietary (See Copyright Notice on Page 2)

95

Contents

Main Linksys PAP2 and RT31P2 Disclaimer Please Read: Use of Proprietary Information and Copyright Notice: Page Page Page 1. Introduction 1.1. The Session Initiation Protocol Page 1.1.1. Components of a SIP Network Service Provider Domain Subscriber Domain IP Network (Internet) 1.1.2. Provisioning Overview 1.1.3. Security Overview 1.1.4. SIP Services Page Page Page 1.2. Network Address Translation (NAT) Traversal 1.2.1. What is a NAT or NAPT (Network Address Port Translator)? 1.2.2. VoIP-NAT Interworking 1.3. Voice Quality Overview 2. Hardware Overview Page 2.1. Phone Adapter LED Status 2.2. Broadband Router (RT31P2) LED Status 3. Software Configuration Mechanisms 3.1. Configuration Profile Formats Page 3.1.1. Using the Supplemental Profile Compiler 3.1.2. Encrypting and Compressing XML configuration files 3.2. Secure Initial Configuration 3.3. Web Interface 3.3.1. Web Interface Conventions 3.3.2. Administration Privileges 3.3.3. Basic and Advanced Views 3.4.1. Upgrade URL 3.4.2. Resync URL 3.4.3. Reboot URL 3.4.4. Factory Reset URL 3.5. Configuration via the IVR (PAP2 only) Page Page 4. Configuration Parameters 4.1. Data Types Page 2004 Linksys Proprietary (See Copyright Notice on Page 2) 4.1.1. Conventions 4.2. Provisioning Related Parameters Page Page Page Page Page Page Page 4.2.1. Firmware Upgrade Page Page 4.2.2. Provisioning Server Redundancy 4.2.3. Configuring the Web Server and IVR 4.3. Basic Networking Configuration 4.4. Basic Account Configuration 4.5. Configuration for NAT Traversal Page 4.6. Media and SDP (Session Description Protocol) Configuration 4.6.1. DTMF and Hookflash 4.6.2. Codec and Audio Settings 4.6.3. Dynamic Payload Types and SDP Codec Names 4.6.4. Secure Media Implementation: Page 4.6.5. Outbound Call Codec Selection Codes: 4.7. Supplementary Services 4.7.1. Supplementary Services activated internally Page 4.7.2. Call Forwarding Implemented internally 4.7.3. Supplementary Services implemented in the service provider network 4.8. Dial Plan Configuration Page Page Page Page 4.8.1. Speed Dialing Settings 4.9. Progress Tone and Ring Configuration 4.9.1. Distinctive Ring and Other Ring Settings Page 4.9.2. Progress Tones 4.10. Less Frequently Used Paramters Page Page 4.10.2. Additional User Account Information Page 4.10.3. Per-Line Polarity Settings 4.10.4. Additional Timer Values (sec) 4.10.5. Miscellaneous Parameters Page Figure: PHONE ADAPTER Caller ID Delivery Architecture 5. Expected Feature Behavior 5.1. Originating a Phone Call 5.2. Receiving a Phone Call 5.3. Caller ID 5.4. Calling Line Identification Presentation (CLIP) 5.5. Calling Line Identification Restriction (CLIR) Caller ID Blocking 5.6. Call Waiting 5.7. Disable or Cancel Call Waiting 5.8. Call-Waiting with Caller ID 5.9. Voice Mail 5.10. Attendant Call Transfer 5.11. Unattended or Blind Call Transfer 5.12. Call Hold 5.13. Three-Way Calling 5.14. Three-Way Ad-Hoc Conference Calling 5.15. Call Return 5.16. Automatic Call Back 5.17. Call FWD Unconditional 5.18. Call FWD Busy 5.19. Call FWD - No Answer 5.20. Anonymous Call Blocking 5.21. Distinctive / Priority Ringing and Call Waiting Tone 5.22. Speed Calling Up to Eight (8) Numbers or IP Addresses 6. Troubleshooting 6.1. Call Statistics Reporting 6.2. Enabling Logging and Debugging 6.3. Error and Log Reporting 6.4. Internal Error Codes 6.5. Provisioning and Upgrade result codes 6.6. Table of SIP Response Codes (Error Codes) 7. Summary of Implemented Features and Specifications 7.1. Data Networking Features 7.1.1. MAC Address (IEEE 802.3) 7.2. Voice Features 7.2.3. Secure Calls 7.2.4. Voice Algorithms: 7.2.5. Codec Selection 7.2.6. Dynamic Payload 7.2.7. Adjustable Audio Frames Per Packet 7.2.10. Call Progress Tone Generation 7.2.11. Call Progress Tone Pass Through 7.2.12. Jitter Buffer Dynamic (Adaptive) 7.2.13. Full Duplex Audio 7.2.14. Echo Cancellation Up to 8 ms Echo Tail 7.2.20. Message Waiting Indicator Tones MWI 7.2.21. Polarity Control 7.2.22. Calling Party Control CPC 7.2.23. International Caller ID Delivery 7.2.24. Streaming Audio Server SAS 7.2.25. Music On Hold MOH Page 7.3. Security Features dministration and Maintenance Features ers 7.4. A 8. List of all configuration paramet Page Page Page Page Page Page Page Page Page Page 9. Acronyms Page 10. Glossary