Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems OL-16447-01 manual Installation Guidelines, 149F 65C Statement, 140F 60C Statement

Models: OL-16447-01

1 102

Download 102 pages 41.83 Kb

Page 30

149•F (65•C) Statement 1047

Chapter 2 Switch Installation

Installation Guidelines

These warning statements apply to the Cisco ME 3400E-24TS-M and the Cisco ME 3400EG-12CS-M:

Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of:

149•F (65•C) Statement 1047

Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028

This warning statement applies to the Cisco ME 3400EG-2CS-A:

Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of:

140•F (60•C) Statement 1047

Installation Guidelines

Before installing the switch, verify that these guidelines are met:

•For Ethernet ports, including the 10/100, the 10/100/1000 dual-purpose, and 1000BASE-T SFP module ports, cable lengths from the switch to connected devices can be up to 328 feet (100 meters).

•For cable requirements for SFP module connections, see the “Cable Pinouts” section on page B-6.

•Operating environment is within the ranges listed in Appendix A, “Technical Specifications.”

•Front-panel indicators can be easily read, and access to ports is sufficient for unrestricted cabling.

•AC-power cord reaches from the power outlet to the connector.

•Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent lighting fixtures. Make sure that the cabling is safely away from other devices that might damage the cables.

•Airflow around the switch and through the vents is unrestricted.

Note If the switch is installed in a closed or multirack assembly, the temperature around it might be greater than normal room temperature.

•Before you connect the switch to a power source, note the power consumption specifications in Appendix A, “Technical Specifications.”

Cisco ME 3400E Ethernet Access Switch Hardware Installation Guide

2-4	OL-16447-01

Image 30

Cisco Systems OL-16447-01 manual Installation Guidelines, 149F 65C Statement, 140F 60C Statement

Contents

800 553-NETS Fax 408 FebruaryCisco Systems, Inc 170 West Tasman Drive San Jose, CA Cisco ME 3400E Ethernet Access Switch Hardware Installation GuideReorient or relocate the receiving antenna Alarm Input Port Obtaining Documentation and Submitting a Service RequestSwitch Models Alarm LEDsVerifying Switch Operation Installing the SwitchInstalling and Removing SFP Modules Mounting the Switch on a WallClearing the Switch IP Address and Configuration TroubleshootingPort and Interface Settings Switch LEDsContents IP Settings C-2Completing the Setup Program C-2 Cisco ME 3400E Ethernet Access Switch Hardware Installation GuidePreface AudiencePurpose Cisco ME 3400E Ethernet Access Switch Command Reference Release Notes for the Cisco ME 3400E Ethernet Access SwitchCisco ME 3400E Ethernet Access Switch Software Configuration Guide Cisco ME 3400E Ethernet Access Switch Hardware Installation GuideObtaining Documentation and Submitting a Service Request Cisco Small Form-Factor Pluggable Modules Compatibility MatrixPreface Obtaining Documentation and Submitting a Service Request Cisco ME 3400E Ethernet Access Switch Hardware Installation GuideOL-16447-01 Setting Up the Switch, page Switch Models, page Front Panel, page Setting Up the SwitchSwitch Models Rear Panel, page Power Supply Features, page Fans, pageFront Panel Switch ModelDescription Figure 1-2 Cisco ME 3400EG-12CS-M Front Panel AC- and DC-Power Input Connectors Alarm Input PortFigure 1-3 Cisco ME 3400EG-2CS-A Front Panel Dual-Purpose Ports Management Port10/100 Fast Ethernet Ports SFP ModulesSFP Module Patch Cable UNIs, NNIs, and ENIs Switch LED Panels, page Power-Supply Module LEDs, pageEthernet Management Port LED, page Alarm LEDs, page Port LEDs, page LEDsSwitch LED Panels ColorSystem Status PSU 1 and PSU 2 Power-Supply LEDs Power-Supply Module LEDsFigure 1-7 Switch Power-Supply LEDs System LED continuedAC-Power-Supply LEDs Ethernet Management Port LED1-10 DC-Power-Supply LEDsDual-Purpose Port LEDs Alarm LEDsPort LEDs 1-11Rear Panel 1-12Figure 1-8 Example of the Switch Dual-Purpose Port LEDs Power Supply Features 1-131-14 FansManagement Options Chassis AirflowNetwork Configurations 1-15Chapter 1 Product Overview Management Options 1-16Cisco ME 3400E Ethernet Access Switch Hardware Installation Guide OL-16447-01Verifying Switch Operation, page Installing the Switch, page Switch InstallationWarnings, page Installation Guidelines, page Installing and Removing SFP Modules, pageWarning Class 1 laser product. Statement Warning No user-serviceable parts inside. Do not open. Statement Installation Guidelines 149F 65C Statement140F 60C Statement Powering Off the Switch Verifying Switch OperationInstalling the Switch Rack-Mounting, page Wall-Mounting, pageAttaching Brackets to the Switch, page Mounting in a Rack, page Removing Screws from the SwitchRemoving Screws from the Switch, page Rack-MountingAttaching Brackets to the Switch Attaching Brackets for 19-Inch Racks Figure 2-5 Attaching Brackets for 19-Inch, 23-Inch, and 24-Inch Racks Chapter 2 Switch Installation Installing the SwitchCisco ME 3400E Ethernet Access Switch Hardware Installation Guide OL-16447-01Attaching Brackets for 23-Inch Racks 2-10Figure 2-6 Attaching Brackets for 23-Inch Racks Attaching Brackets for 24-Inch Racks 2-11Figure 2-7 Attaching Brackets for 24-Inch Racks Chapter 2 Switch Installation Installing the Switch Attaching Brackets for ETSI Racks2-12 Cisco ME 3400E Ethernet Access Switch Hardware Installation GuideMounting in a Rack 2-13Attaching Brackets for Wall-Mounting Mounting the Switch on a Wall, pageWall-Mounting Attaching Brackets for Wall-Mounting, pageMounting the Switch on a Wall 2-15Phillips flat-head screw Chapter 2 Switch Installation Installing the Switch Cisco ME 3400EG-12CS-M2-16 Cisco ME 3400E Ethernet Access Switch Hardware Installation GuideChapter 2 Switch Installation Installing the Switch Cisco ME 3400E-24TS-M2-17 Cisco ME 3400E Ethernet Access Switch Hardware Installation GuideCisco ME 3400EG-2CS-A 2-18Figure 2-15 Mounting the Cisco ME 3400EG-2CS-A on a Wall Table- or Shelf-Mounting Installing and Removing SFP ModulesInstalling SFP Modules 2-192-20 Step 5 Insert the cable connector into the SFP moduleInserting and Removing the SFP Module Patch Cable Removing SFP Modules2-21 Connecting to the 10/100 and 10/100/1000 Ports Removing the SFP Module Patch Cable2-22 2-23 Step 3 Reconfigure and reboot the connected device, if necessaryConnecting to Fiber-Optic SFP Modules 2-24Connecting to 1000BASE-T SFP Modules 2-25Figure 2-23 Connecting to a 1000BASE-T SFP Module 2-26 Connecting to Dual-Purpose PortsWhere to Go Next Figure 2-24 Connecting to a Dual-Purpose PortProduct Overview, page Power-Supply Module Installation, page Installing and Removing AC- and DC-Power-Supply ModulesPower-Supply Module Description Power Supply Settings, pageHandle-Side Description Figure 3-2 80-W DC-Power-Supply Module Handle Side PSU OKFigure 3-3 DC-Voltage Selector Tools and Equipment, page Installation Guidelines, page Power-Supply Module InstallationConnector-Side Description Installing an AC-Power-Supply Module, pageInstallation Guidelines Tools and EquipmentInstalling an AC-Power-Supply Module AC-1 PSU-1 AC-2 PSU-2Removing AC-Power-Supply Modules 3. Installing the DC-Power-Supply Module in the Switch, page Installing a DC-Power-Supply Module1. Preparing for Installation, page 2. Grounding the Switch, page 4. Wiring the DC-Input Power Source, pagePreparing for Installation Grounding the SwitchFigure 3-9 DC-Power-Supply Diagram 3-10 Remove the ground screw from the switch rear panelFigure 3-12 Attaching the Ground Lug and Wire Assembly Installing the DC-Power-Supply Module in the Switch3-11 Figure 3-13 Inserting a DC-Power-Supply ModuleWiring the DC-Input Power Source 10 A Statement3-12 3-13 Step 2 Locate the terminal block plug see Figure3-14 Return positive Feed A3-15 Figure 3-21 Inserting the Terminal Block in the Block HeaderRemoving the DC-Power-Supply Module 3-16Figure 3-22 DC-Power Terminal Block With Two Feeds Power Supply Settings 3-17Power Supply Settings 3-18Chapter 3 Installing and Removing AC- and DC-Power-Supply Modules Cisco ME 3400E Ethernet Access Switch Hardware Installation GuideSwitch POST Results TroubleshootingDiagnosing Problems Diagnosing Problems, pageBad or Damaged Cable Switch LEDsSwitch Connections Ethernet and Fiber CablesPing the End Device SFP Module Port IssuesPort and Interface Settings Spanning Tree LoopsSpeed, Duplex, and Autonegotiation Clearing the Switch IP Address and ConfigurationSwitch Performance Autonegotiation and NICsFinding the Switch Serial Number Appendix 4 Troubleshooting Finding the Switch Serial Number Cisco ME 3400E Ethernet Access Switch Hardware Installation GuideOL-16447-01 Environmental Ranges and Technical Specifications for the Switch Technical SpecificationsEnvironmental Ranges and Technical Specifications for the Switch A P P E N D I X A32 to 131F 0 to 55C 32 to 140F 0 to 60COperating Temperatures for the Cisco ME 3400EG-12CS-M Table A-4Physical Dimensions AC-Power RequirementsDC-Power Requirements Table A-6 Technical Specifications for the Cisco ME 3400EG-12CS-M Table A-7 Technical Specifications for the Cisco ME 3400EG-2CS-A ModulesTable A-9 Page Appendix A Technical Specifications Cisco ME 3400E Ethernet Access Switch Hardware Installation GuideOL-16447-01 Connector Specifications, page B-1 Cables and Adapters, page B-4 Connector and Cable SpecificationsConnector Specifications 10/100, page B-1 SFP Module Connectors, page B-2SFP Module Connectors Dual-Purpose Ports 10/100 Ethernet Management PortAlarm Input Port Figure B-3 10/100/1000 Port PinoutsSFP Module Cables, page B-4 Cable Pinouts, page B-6 Cables and AdaptersSFP Module Cables Console Port Adapter Pinouts, page B-7Page Two Twisted-Pair Straight-Through Cable Schematic Cable PinoutsSwitch 1 TP0+ 2 TP0 3 TP1+ 6 TP1 4 TP2+ 5 TP2 7 TP3+ 8 TP3 Two Twisted-Pair Crossover Cable SchematicRJ-45-to-DB-9 Console Port Adapter PinoutsSwitch Console ConsoleTable B-3 Console Port Signaling Using a DB-25 Adapter Starting the Terminal-Emulation Software Configuring the Switch with the CLI-Based Setup ProgramAccessing the CLI Through the Console Port A P P E N D I X CEntering the Initial Configuration Information IP SettingsCompleting the Setup Program Page Page Numerics I N D EIN-1 IN-2 IN-3 IN-4 IN-5 IN-6