Cisco Systems PA-T3 manual Software and Hardware Requirements, PA-2T3

Software and Hardware Requirements

Software and Hardware Requirements

Table 2-1 lists the minimum Cisco IOS software release required to use the PA-T3 and the

PA-2T3 serial port adapters in supported router platforms.

Table 2-1	PA-T3 Port Adapter Software Requirements
Platforms		Recommended Minimum Cisco IOS Release
Cisco 7000 and Cisco 7500 series		PA-T3	PA-2T3

•	With VIP2-15(=) or VIP2-40(=)	Cisco IOS Release 11.1(13)CA or a later
		release of Cisco IOS Release 11.1 CA
•	With VIP2-50(=)	Cisco IOS Release 11.1(14)CA or a later
		release of Cisco IOS Release 11.1 CA

Cisco IOS Release 11.1(16)CA or a later release of Cisco IOS Release 11.1 CA

Cisco IOS Release 11.1(16)CA or a later release of Cisco IOS Release 11.1 CA

Cisco 7200 series

• Cisco 7204VXR and Cisco 7206VXR	Cisco IOS Release 12.0(2)XE2 or a later
	release of Cisco IOS Release 12.0 XE
	Cisco IOS Release 12.0(3)T or a later release
	of Cisco IOS Release 12.0 T
• Cisco 7204 and Cisco 7206	Cisco IOS Release 11.1(16)CA or a later
	release of Cisco IOS Release 11.1 CA
• Cisco 7202	Cisco IOS Release 11.1(19)CC1 or a later
	release of Cisco IOS Release 11.1 CC
	Cisco IOS Release 11.3(4)AA or a later
	release of Cisco IOS Release 11.3 AA

Cisco IOS Release 12.0(2)XE2 or a later release of Cisco IOS Release 12.0 XE Cisco IOS Release 12.0(3)T or a later release of Cisco IOS Release 12.0 T

Cisco IOS Release 11.1(16)CA or a later release of Cisco IOS Release 11.1 CA

Cisco IOS Release 11.1(19)CC1 or a later release of Cisco IOS Release 11.1 CC Cisco IOS Release 11.3(4)AA or a later release of Cisco IOS Release 11.3 AA

Cisco uBR7200 series

• Cisco uBR7246 and Cisco uBR7223	Cisco IOS Release 12.0(2)XA or a later
	release of Cisco IOS Release 12.0 XA

Cisco IOS Release 12.0(2)XA or a later release of Cisco IOS Release 12.0 XA

Cisco 7100 Series

• Cisco 7120 series and Cisco 7140 series	Cisco IOS Release 12.0(4)XE or a later
	release of Cisco IOS Release 12.0 XE
	Cisco IOS Release 12.0(5)T or a later release
	of Cisco IOS Release 12.0 T
Catalyst 5000 series switches

•With Catalyst RSM/VIP2-15(=) or Catalyst RSM/VIP2-40(=)

Cisco IOS Release 12.0(4)T or a later release of Cisco IOS Release 12.0T

Cisco IOS Release 12.0(4)T or a later release of Cisco IOS Release 12.0T

Caution The VIP2 requires that the host Cisco 7000 series router have the RSP7000 and RSP7000CI installed. The VIP2 does not operate properly with the Route Processor (RP), Switch Processor (SP), or Silicon Switch Processor (SSP) installed in the host Cisco series router.

The PA-T3 serial port adapter is considered a high-bandwidthport adapter; therefore, and at a minimum, Cisco recommends that the PA-T3 serial port adapter be installed on the VIP2-15 or Catalyst RSM/VIP2 motherboard (with 1 MB of SRAM and 8 MB of DRAM). Installation of the PA-T3 serial port adapter on the VIP2-10 (with 512 KB of SRAM and 8 MB of DRAM) is not recommended.

2-2PA-T3 Serial Port Adapter Installation and Configuration