Compaq EK-SMCPO-UG. C01 Replacing Components (FRUs)

3-6 RAID Array 3000 Pedestal Storage Subsystem Hardware User’s Guide

Compaq Confidential – Need to Know Required

Writer: Bob Young Project: RAID A rray 3000 Pedestal Storage Subsystem Hardware User’s Guide Comments:

Part Number: EK-SMCPO-UG. C01 File Name: d-ch3 Maintenance.doc Last Saved On: 12/4/00 1:50 PM

Whenever any of the following error conditions occur, the amber fault LED on

the front of the pedestal will turn on. When alarm switch S1 on the rear panel

of the pedestal is in the up (enabled) position, the audible alarm will sound

whenever one of the following conditions occurs:

■ Loss of AC power to one of the power supplies

■ Failure of either power supply fan

■ UPS not connected

■ UPS power failure

■ UPS output too low

■ Temperature exceeds 123ºF (50ºC)

■ One of the +12 VDC outputs is less than + 9.85 VDC

■ One of the +5 VDC outputs is less than + 3.95 VDC

■ Miscellaneous error condition

■ A controller error condition exists

■ External fault

Replacing Components (FRUs)

This section describes how to replace an FRU in the RAID Array 3000

pedestal. The information is divided into the following subsections:

■ Removing the pedestal door

■ Replacing an SBB

■ Replacing a power supply

■ Replacing the controller

■ Replacing the EMU board

■ Replacing the UPS

■ Replacing a controller memory cache module

Contents

Main Compaq StorageWorks Page Contents About This Guide Chapter 1 Product Overview Chapter 2 RAID Array Controller Chapter 3 Maintenance Chapter 4 Expansion Pedestal Option Chapter 5 Second Controller Option List of Figures Page List of Tables Page About This Guide Purpose and Scope Intended Audience Document Structure Page Related Documents Table 1 Related Documents Text Conventions Symbols in Text Symbols on Equipment xiv RAID Array 3000 Pedestal Storage Subsystem Hardware User's Guide Compaq Confidential Need to Know Required This is a test Rack Stability Getting Help Compaq Technical Support Compaq Website Compaq Authorized Reseller Chapter 1 Product Overview Product Description Page Product Overview 1-3 Table 1-1 RAID Array 3000 Pedestal Part Numbers and Model Descriptions Pedestal Features Pedestal Cabinet Page Pedestal Components StorageWorks Building Blocks (SBBs) RAID Array Controller Pedestal Power Supplies UPS Environmental Monitor Unit (EMU) Product Overview 1-9 Figure 1-5 shows the Pedestal rear panel components. Figure 1-5. Pedestal rear panel components UltraSCSI Buses Product Overview 1-11 Figure 1-8. Slot locations and SCSI ID addresses Figure 1-7. UltraSCSI bus configuration switch Connecting the Pedestal to a Host System Product Overview 1-13 Figure 1-9 shows the Single host, Single Adapter Cabling diagram. Host System Table 1-2 Single Host, Single Adapter Cabling 1-14 RAID Array 3000 Pedestal Storage Subsystem Hardware Users Guide Figure 1-10 shows the Single host, Dual Adapter/dual Controller Cabling diagram. Table 1-3 Single Host, Dual Adapter/Dual Controller Cabling Product Overview 1-15 Table 1-4 Single Host, Single Adapter/Dual Controller (Y-cable connection cabling) 1-16 RAID Array 3000 Pedestal Storage Subsystem Hardware Users Guide Figure 1-12 shows the Dual host, Single Adapter/single Controller Cabling diagram. Table 1-5 Dual Host, Single Adapter/Single Controller Cabling Product Overview 1-17 Specifications Table 1-6 Pedestal Technical Specifications 1-18 RAID Array 3000 Pedestal Storage Subsystem Hardware Users Guide Table 1-7 Pedestal Physical and Power Specification Chapter 2 RAID Array Controller Controller Overview Page Controller Features Page Table 2-1 Controller Specifications Page Controller Reset and LED Indicators Table 2-2 LED/Reset Switch Interface Flexible RAID Set Configuration Performance Enhancements Custom Components Efficient Write and Read Algorithms Write-Back Caching Write Gathering Write On Top RAID Levels Supported Table 2-3 RAID Levels Supported Table 2-4 Pedestal RAID Set Restrictions RAID 0 Page RAID 1 RAID 0+1 Table 2-5 RAID 0+1 Example RAID 4 Page RAID 5 Just a Bunch of Drives (JBOD) Redundant Operation Initialization Message Passing Failover Environmental Backup Power Management Table 2-6 Response to Various AC Power Condition s Voltage Monitoring Temperature Monitoring Page Page Chapter 3 Maintenance Pedestal Status and Power LEDs SBB Status LEDs Table 3-1 Disk Drive SBB Status LEDs Controller LEDs EMU Error Reporting EMU Error Conditions Replacing Components (FRUs) Removing the Pedestal Door Replacing an SBB Page Replacing a Power Supply Replacing the RAID Array Controller Replacing the EMU Board Replacing the UPS Differential/Wide UltraSCSI Bus Table 3-2 SCSI Bus Length and External Cables Table 3-3 Assigned Slot Device Addresses in the Pedest al Reconfiguring the SCSI Bus Page Page Maintenance 3-17 Replacing the Controller Memory Cache Modules Page Page Chapter 4 Expansion Pedestal Opt ion Product Description Expansion Pedestal Cabinet Page Expansion Pedestal Components Page Reconfiguring Base Pedestal UltraSCSI Bus Page Page Page Page Page Page Expansion Pedestal Option 4-15 UPS, and the AC power source (Figure 415). Chapter 5 Second Controller Option Second Controller Option Kit Installing the Upgrade Saving Existing Configuration Updating Firmware Updating Firmware Using SWCC Updating Firmware Using Serial Interface Shutting Down the RA3000 Installing Two SIMMs into Second Controller Replacing Existing Controller Restoring the Configuration Updating Firmware on Second Controller Installing Original Controller Configuring a Dual Controller Installation for a Single Serial Port Configuring the RA3000 for the Active Mode of Operation Configuring the Dual Controllers Connecting to Your Dual Controller Storage System Verifying the Controller Operating Parameters