Line Configuration/Type | Cortelco 2750 instruction

f.Use the dial pad numbers to enter the name for the desired station.

g.Press the soft key under SAVE.

Repeat steps “a” through “g” for any additional stations you wish to name.

The table below shows which dial pad numbers to press for all the different letters and special characters.

Note that you can press the 0, *, and # buttons if you want those characters, and you can press the down arrow button below the display to leave an empty space. Press the DELETE button to make corrections.

0	0

1	,	-	'	&	.	(	)	1

2	A	B	C	a	b	c	2

3	D	E	F	d	e	f	3

4	G	H	I	g	h	i	4

5	J	K	L	j	k	l	5

6	M	N	O	m	n	o	6

7	P	Q	R	S	p	q	r	s	7

8	T	U	V	t	u	v	8

9	W	X	Y	w	x	y	9

*	*

#	#

2.3.Line Configuration/Type

While you must share the same Line 1 telephone number at all the stations, you may choose to leave some lines unconnected at particular stations or to connect private lines to Lines 2, 3 or 4 at particular stations.

Common:This is the factory setting for all lines. This setting assumes that the telephone line is connected to the same telephone line button at all stations.

Private:Use this setting at any telephone that is connected to a different telephone number than the corresponding line at the other stations. For example, you may connect your private telephone number to Line 3 at your station instead of connecting your station to the common Line 3. In this example, you would set Line 3 at your station as PRIVATE.

Unconnected:Use this setting at any telephone that is not physically connected to all of its lines. For example, you may install a 2750 4-line telephone in a room that is currently wired for only lines 1, 2 and 3. In this example, you would set Line 4 at this station as UNCONNECTED.

10	2750 User Guide Version 1.3

Image 16

Cortelco 2750 instruction manual Line Configuration/Type

Contents

OWNER’S Instruction Manual Table of Contents Memory Settings Iii User Guide Version Using Your Telephones Answering System Using Stanard Telephones Thank YOU For Purchasing Feature List User Guide Version Important Safety Instructions Unpacking and Installation Box Contents Telephone Part Identification Identify Your Existing Wiring System Plan Your InstallationStandard Installation Installations with Private Lines and Unconnected Lines Assign a Station Number Install Batteries OptionalConnect Cords to Telephone Verify Proper Installation System ProgrammingStation Number Assignment Station Name Assignment Line Configuration/Type Loop Voltage Detector To Set Connections/ConfigurationTo Set Loop Voltage Detector Setting Distinctive Ringing Ringer ConfigurationTo choose how each line will ring Intercom Call Response Setting Off-Hook RingingTo choose how your phone will respond to intercom calls To set the system’s toll restriction access code Automatic Line SelectionTo Set Automatic Line Selection Toll Restriction To completely restrict specific lines at a telephone Restricted To set the allowed numbers at a particular telephone System Privacy Dialing Mode To Change the Privacy SettingArea Codes Memory Settings Storing a Caller ID number into memory To store a personal directory dial numberTo Store Caller ID Records To Store the Centrex Prefix Erase All Feature Settings Reset Default SettingsErase Numbers Stored in Memory Erase Toll Restrictions Miscellaneous Settings Adjusting Auto Hold Drop Time Adjusting Flash TimerCaller ID on Call Waiting Cidcw Sensitivity Hold Call Reminder Answering System Setting Your Telephones Pickup Delay Setting Toll SaverChanging your OGM New Message Beep Remote Code Setting Message LengthAuto-Attendant Record your Auto Attendant Day OGM Set up the Auto AttendantRecord your Auto Attendant Night OGM Night Timer Set Setting Auto Attendant Pickup DelayRecord your Auto Attendant Zero-Out OGM Setting More Than One Phone as an Auto Attendant Using Additional Auto Attendant OGMsSetting Separate Auto Attendant OGMs for Different Lines To record additional Auto Attendant OGM All Transfer Feature Turn Off the Auto Attendant on One or More LinesChoosing the Zero-Out Action Leave a Message at the Auto Attendant Transfer Direct to Voice Mail Summary of Auto Attendant Actions Telephone Operation Answering a call on another line ConferenceOutside Calls Outside Call with Intercom Station Blind Transfer Transfer RingPersonal Ring Caller ID Volume Levels Dialing CallsDeleting Numbers Ringer Accessing Messages Resetting MSG LampSpeakerphone Intercom Speaker Flash MuteDo Not Disturb DND Line Reserve Timer Elapsed Call Time Call PrivacyToll Restriction Removal Single Call Toll Restriction Removal Single Station Timer Reset Elapsed Call Time Previous CallsHeadset Directory Card Intercom while Idle Intercom while on an Outside CallAnswering Intercom Calls Intercom Ring Intercom Voice All Answering Pages SingleBlocking Pages Room Monitoring Using Your Telephones Answering System Listening to your Messages Play MessagesStop Message Playback Pause Message Playback Using Dial Pad Repeat a MessageSkip to the next Message Jump back Erasing Messages To Erase a Message To Erase All MessagesRecording a Memo or Conversation Recording a Telephone Conversation Using Stanard Telephones To Repeat an Auto Attendant OGMLine Status and Calls on Hold Intercom Power Failure Operation Battery ReplacementBatteries Appendix a Phone SettingsMenu Tree ON/OFF Answer Settings Menu Options SUB Menu Default Time and Date Settings Memory SettingsAdvanced Settings Installation Worksheet Appendix B Appendix C Toll Restriction Worksheet Trouble Shooting Guide Appendix D FCC Information Telephone Repair Limited Warranty Repair Center Sawyer Road Corinth, Mississippi