Error messages
NOTE
•An error message is displayed if Auto Setup could not be completed due to speaker placement, the measurement environment, etc. Check the related items, and implement the necessary measures. After resolving the error, perform Auto Setup again.
•If the result still differs from the actual connection status after remeasurement or the error message still appears, it is possible that the speakers are not connected properly. Turn this unit off, check the speaker connections and repeat the measurement process from the beginning.
•Be sure to turn off the power before checking speaker connections.
| Examples |
|
|
|
|
| Error details | Measures | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| • Correct measurement is not possible due to inappropriate subwoofer | • When using a subwoofer with |
| AUTO SETUP |
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
| volume. | “SW Level Matching” to adjust the subwoofer volume (vpage 17 |
| Caution! | 1 2 3 4 5 6 |
|
| ||||||||
| The subwoofer's level is too high or low. Please select "SW |
| “Adjusting the subwoofer volume level”). | |||||||||
| Level Matching" and adjust the level of your subwoofer unit. |
| ||||||||||
| If you do not want to use the |
|
|
|
|
|
|
|
|
|
| • When using a subwoofer without a |
| subwoofer, select "Skip". |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| and then press ENTER. |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SW Level Matching |
|
|
|
|
|
|
| ||||
| Skip |
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| • The connected setup microphone is broken, or a device other than | • Connect the included setup microphone to the SETUP MIC jack of | ||||
| AUTO SETUP |
|
|
|
|
| ||||||
|
|
|
|
|
|
| the supplied setup microphone is connected. | this unit. | ||||
| Caution! |
|
|
|
|
| ||||||
| No microphone or speaker |
|
|
|
|
| • Not all speakers could be detected. | • Check the speaker connections. | ||||
|
|
|
|
|
|
|
|
|
|
| • The front L speaker was not properly detected. |
|
| Retry |
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| AUTO SETUP |
|
|
|
|
| • There is too much noise in the room for accurate measurements to | • Either turn off any device generating noise or move it away. | ||||
| Caution! |
|
|
|
|
| be made. | • Perform again when the surroundings are quieter. | ||||
| Ambient noise is too high |
|
|
|
|
| • Speaker or subwoofer sound is too low for accurate measurements | • Check the speaker installation and the direction in which the speakers | ||||
| or Level is too low |
|
|
|
|
| to be made. | are facing. | ||||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| • Adjust the subwoofer’s volume. |
| Retry |
|
|
AUTO SETUP |
| • The displayed speaker could not be detected. | • Check the connections of the displayed speaker. |
Caution! | 1 2 3 4 5 6 | (The screen on the left indicates that the front right speaker cannot |
|
Front R | None | be detected.) |
|
Retry |
|
|
|
AUTO SETUP |
| • The displayed speaker is connected with the polarity reversed. | • Check the polarity of the displayed speaker. |
Caution! | 1 2 3 4 5 6 | (The screen on the left indicates that the polarity phases of the front | • For some speakers, this error message may be displayed even if |
Front R | Phase | right speakers are reversed.) | the speaker is properly connected. If you are sure the connection is |
|
|
| correct, press ui to select “Skip”, then press ENTER. |
Retry |
|
|
|
Skip |
|
|
|
Getting Started Connections Setup Other Operations
21
