|
|
|
|
|
|
|
|
|
|
| ENGLISH | |
|
|
|
|
|
|
|
|
|
|
| Set up speakers (Audyssey® Auto Setup) |
|
| About setup microphone placement |
| 1 | Set up the microphone | 3 | Set up the remote control unit | Simple | |||||
|
| version | ||||||||||
|
|
|
| |||||||||
• Measurements are performed by placing the setup microphone | Mount the setup microphone on a tripod or stand |
| nn Set up the zone mode | |||||||||
successively at multiple positions throughout the entire listening | and place it in the main listening position. |
| Press ZONE SELECT to switch the zone mode to |
| ||||||||
area, as shown in GExample qH. For best results, we recommend | When placing the setup microphone, adjust the height of the |
| “MAIN”. |
| ||||||||
you measure in six positions, as shown in the illustration (up to six | sound receptor to the level of the listener’s ear. |
| The “MAIN” indicator lights. |
| ||||||||
positions). |
|
|
|
|
|
| Sound receptor |
|
| Basic | ||
• Even if the listening environment is small as shown in GExample wH, |
| Setup |
|
| ||||||||
measuring at multiple points throughout the listening environment |
| microphone |
|
| ||||||||
|
|
|
| |||||||||
results in more effective correction. |
|
|
|
|
|
|
| version | ||||
| GExample qH |
|
| GExample wH |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| ||||
| FL SW C | FR |
|
| FL SW C | FR |
|
|
|
|
|
|
| ( : Measuring positions) |
|
| ( : Measuring positions) |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| Press ZONE SELECT |
|
|
|
|
|
|
|
|
|
|
|
| nn Set up the operation mode |
|
| *M |
|
|
| *M |
| • Do not hold the setup microphone in your hand during |
| Press AMP to set the remote control unit to amplifier | Advanced | ||
SL |
| SR | SL | SR | NOTE |
|
| operation mode. |
| |||
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
| |
FL | Front speaker (L) | SW Subwoofer |
|
| measurements. |
|
|
| version | |||
|
| • Avoid placing the setup microphone close to a seat back or wall as |
|
| ||||||||
|
|
|
|
| ||||||||
FR | Front speaker (R) | SL | Surround speaker (L) |
|
|
|
| |||||
| sound reflections may give inaccurate results. |
|
|
| ||||||||
C | Center speaker |
| SR | Surround speaker (R) |
|
|
|
| ||||
|
|
|
|
|
|
| ||||||
| About the main listening position (*M) |
|
| 2 | Set up the subwoofer |
|
|
| |||||
The | main listening | position is the | position where | listeners would | If using a | subwoofer capable of the following |
|
|
| |||
normally sit or where one would normally sit alone within the listening |
| Press AMP |
| |||||||||
| adjustments, set up the subwoofer as shown below. |
|
| ||||||||||
environment. Before starting Audyssey Auto Setup, place the setup |
|
| ||||||||||
microphone in the main listening position. Audyssey MultEQ® uses | nn When using a subwoofer with a direct mode |
|
|
| ||||||||
the measurements from this position to calculate speaker distance, | Set the direct mode to “On” and disable the volume adjustment |
|
|
| ||||||||
level, polarity, and the optimum crossover value for the subwoofer. | and crossover frequency setting. |
|
|
| ||||||||
|
|
|
|
|
|
|
| nn When using a subwoofer without a direct mode |
|
|
| |
|
|
|
|
|
|
|
| Make the following settings: |
|
|
| |
|
|
|
|
|
|
|
| • Volume : “12 o’clock position” |
|
| Information | |
|
|
|
|
|
|
|
| • Crossover frequency : |
|
| ||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| “Maximum/Highest Frequency” |
|
|
| |
|
|
|
|
|
|
|
| • Low pass filter : “Off” |
|
|
| |
|
|
|
|
|
|
|
| • Standby mode : “Off” |
|
|
| |
The “Simple version” describes the installation, connection and setup methods for | 7 |
See page 28 for the installation, connection and setup methods for speakers other than