ENGLISH

Set up speakers (Audyssey® Auto Setup)

Preparation

Step 1

 

 

 

 

Step 2

 

Speaker Detection

 

 

 

Measurement

 

Connect the setup microphone to the

• In step 1, you will perform measurements at the main listening position.

 

 

• In step 2, you will perform measurements at

• This step automatically checks the speaker configuration and speaker size, and calculates the channel

multiple positions (two to six positions) other than

4 SETUP MIC jack of this unit.

level, distance, and crossover frequency. It also corrects distortion in the listening area.

 

the main listening position.

 

 

6 The detected speakers are displayed.

If “Caution” is displayed:

 

• You can achieve a more effective correction of

 

 

measurements at multiple positions.

 

 

 

NOTE

 

 

distortion within the listening area by performing

 

 

MultEQ

Go to “Error messages” (vpage 10), check

Move the setupmicrophone to

 

 

any related items,

and perform the necessary

 

Step1:Speaker Detection

 

 

 

8 position 2, use ui to select “Next”,

 

Front Sp.

:Yes

procedures.

 

 

 

Center Sp.

:Yes

If the problem is

resolved, return and restart

When the setup microphone is

Subwoofer

:Yes

“Audyssey Auto Setup”.

 

and then press ENTER.

Surround Sp.

:Yes

 

The measurement of

the second position

connected, the following screen is

 

 

 

 

 

Next

 

When performing Audyssey Auto

 

starts. Measurements can be made in up to

displayed.

 

 

 

 

 

 

 

 

 

Retry

 

Setup over again

 

six positions.

 

3-1.Audyssey Auto Setup

[ENT]:Next

 

 

Step2:Measurement

 

 

Press ui to select “Retry”, and then press

MultEQ

NOTE

 

 

MultEQ

Please place microphone

 

ENTER.

 

 

Please place microphone

at ear height at

 

 

 

 

 

at ear height at

main listening position.

If a connected speaker is not displayed, the

When measuring has stopped

 

2nd listening position.

Amp Assign:

speaker may not be connected correctly. Check

 

Next

 

ZONE2

the speaker connection.

 

q Press ui to select “Cancel”, then press

 

Calculate

Start

 

 

ENTER.

 

 

Cancel

 

Cancel

Use ui to select “Next” and then

 

 

 

 

[ENT]:Select [RTN]:Back

w Press o p to select “Yes”, then press ENTER.

[ENT]:Next

 

Here, we explain setup using the example of

7 press ENTER.

 

Setting up the speakers again

 

 

 

5.1-channel speaker playback.

 

 

 

If you want to omit measurements from the next

For settings other than 5.1-channel surround,

 

 

Repeat the operation from step 4 of Preparation

.

 

 

position onward, select “Calculate”.

select “Amp Assign” and perform steps 3 to 4 of

 

 

 

 

 

 

 

 

 

(Go to Step 3 Calculating

)

“Set up speakers” (vpage 31).

 

 

 

 

 

 

 

 

 

 

 

 

5 Use ui to select “Start” and then press ENTER.

When measuring begins, a test tone is output from each speaker.

• Measurement requires several minutes.

If “Cancel” is selected

“Cancel Auto Setup?” is displayed on the TV screen. If “Yes” is selected, “Audyssey Auto Setup” closes.

9 Repeatto 6. step 8, measuring positions 3

When measurement of position 6 is completed, a “All the measurements were finished.” message is displayed.

Step2:Measurement

MultEQ

All the measurements were finished.

Calculate

Retry

Cancel

[ENT]:Calculate

8

Remote control operation

Move the cursor

Confirm the setting

Return to previous menu

buttons

(Up/Down/Left/Right)