ENGLISH

Manual Setup

Setting items

Setting details

 

 

Bass Setting

Subwoofer Mode : Select low range signals to be reproduced by

Set subwoofer and LFE

subwoofer.

signal range playback.

• LFE : The low range signal of the channel set to “Small” speaker size is

 

added to the LFE signal output from the subwoofer.

 

• LFE+Main : The low range signal of all channels is added to the LFE

 

signal output from the subwoofer.

 

• “Subwoofer Mode” can be set when “Speaker Config.” – “Subwoofer”

 

(vpage 49) is set to “Yes”.

 

• Play music or a movie source and select the mode offering the strongest

 

bass.

 

• Select “LFE+Main” if you want the bass signals to always be produced

 

from the subwoofer.

 

NOTE

 

If “Front” and “Center” for “Speaker Config.” are set to “Large”, and

 

“Subwoofer Mode” is set to “LFE”, no sound may be output from the

 

subwoofers, depending on the input signal or selected surround mode.

 

LPF for LFE : Set LFE signal playback range.

 

• 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz

Distance

Unit : Set the unit of distance.

Set distance from listening

• Feet / Meters

position to speakers.

Step : Set the minimum variable width of the distance.

Measure beforehand the

• 1ft / 0.1ft

distance from the listening

• 0.1m / 0.01m

position to each speaker.

FL / FR / C / SW / SL / SR / SBLz / SBRz / FHL / FHR : Select the speaker.

zz When the “Speaker Config.” – “S.Back” setting (vpage 49) is set to “1sp”, “S.Back” is displayed.

• 0.0ft – 60.0ft / 0.00m – 18.00m : Set the distance.

• The speakers that can be selected differ depending on the “Amp Assign” (vpage 49) and “Speaker Config.” (vpage 49) settings.

• Default settings :

FL / FR / C / SW / FHL / FHR : 12.0 ft (3.6 m)

SL / SR / SBL / SBR : 10.0 ft (3.0 m)

• Set the difference in the distance between the speakers to less than 20 ft (6.0 m).

NOTE

Speakerssetto“None”in“SpeakerConfig.”(vpage49)arenotdisplayed.

Default : The “Distance” settings are returned to the default settings.

•Yes : Reset to the defaults.

•No : Do not reset to the defaults.

When you select “Default” and press ENTER, the “Default Setting?” prompt is displayed. Select either “Yes” or “No”, and press ENTER.

Setting items

Setting details

 

 

Channel Level

Test Tone Start : Output test tone.

Set the volume of the test

• FL / C / FR / SR / SBRz / SBLz / SL / FHL / FHR / SW : Select the

tone to be the same when it

speaker.

is output from each speaker. zz When the “Speaker Config.” – “S.Back” setting (vpage 49) is set to “1sp”, “S.Back” is displayed.

• –12.0dB – +12.0dB (0.0dB) : Adjust the volume.

• When o is pressed while the subwoofer volume is set to “–12 dB”, the “Subwoofer” setting switches to “OFF”.

• When “Channel Level” is adjusted, the adjusted values are set for all the surround modes. To adjust the channel level separately for the different surround modes, use the operation see page 33.

NOTE

• Speakers set to “None” in the “Speaker Config.” (vpage 49) settings are not displayed.

 

• When a headphones jack is inserted in the PHONES jack of this unit, the

 

“Channel Level” is not displayed.

 

Default : The “Channel Level” settings are returned to the default settings.

 

• Yes : Reset to the defaults.

 

• No : Do not reset to the defaults.

Crossover Frequency

Crossover : Set the crossover frequency.

Set the maximum frequency

• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /

of the bass signal output

250Hz

from each channel to

Advanced : Specify crossover frequency for each speaker.

the subwoofer. Set the

• Front / Center / Surround / S.Back

/ Front Height : Select the speaker.

Crossover Frequency to

• 40Hz

/ 60Hz / 80Hz

/ 90Hz / 100Hz

/ 110Hz / 120Hz / 150Hz / 200Hz /

suit the bass reproduction

capability of the speaker

250Hz : Set the crossover frequency.

 

being used.

 

 

• “Crossover Frequency” can be set when the “Bass Setting” –

 

“Subwoofer Mode” (vpage 50) setting is “LFE+Main”, or when you

 

have a speaker that is set to “Small”.

 

• Always set the crossover frequency to “80Hz”. When using small

 

speakers, however, we recommend setting the crossover frequency to

 

a higher frequency.

 

• For speakers set to “Small”, sound below the crossover frequency

 

is cut from the sound output. The cut bass sound is output from the

 

subwoofer or front speakers.

 

• The speakers that can be set when “Advanced” is selected differ

 

depending on the “Subwoofer Mode” setting (vpage 50).

 

• When “LFE” is selected, speakers set to “Small” at “Speaker Config.”

 

can be set. If the speakers are set to “Large”, “Full Band” is displayed

 

and the setting cannot be made.

 

• If set to “LFE+Main”, this setting can be made regardless of the

 

speaker size.

50

Remote control operation

Move the cursor

Confirm the setting

Return to previous menu

buttons

(Up/Down/Left/Right)