Symptom | Cause/Solution |
| Page | |
Cannot login to |
| • Login information is incorrect. Check if the “Email address” for | 39 | |
Pandora. (“Email |
| Pandora has been properly entered. |
| |
address” or |
| (Password is not displayed.) |
|
|
“Password” is |
| http://www.pandora.com/denon |
|
|
displayed.) |
|
|
|
|
GAirPlayH |
|
|
| |
Symptom | Cause/Solution |
| Page | |
The AirPlay icon |
| • This unit and the computer or iPhone/iPod touch/iPad are not | 12 | |
is not displayed |
| connected to the same network (LAN). Connect the computer or |
| |
in iTunes or on the |
| iPhone/iPod touch/iPad to the same network as this unit. |
|
|
iPhone/iPod touch/ |
| • iTunes or the iPhone/iPod touch/iPad do not have firmware that | 96 | |
iPad. |
| supports AirPlay installed. Update to the latest firmware. |
|
|
No sound. |
| • The volume in iTunes or on the iPhone/iPod touch/iPad is set to | – | |
|
| the minimum setting. Adjust the volume to the optimum level. |
| |
|
| • This unit is not selected in the screen that is displayed when | 64 | |
|
| iTunes or the iPhone/iPod touch/iPad is started. Start iTunes or |
| |
|
| switch on the iPhone/iPod touch/iPad, click the AirPlay icon | in |
|
|
| the displayed screen, and select this unit. |
|
|
GRemote Control UnitH |
|
|
| |
Symptom | Cause/Solution |
| Page | |
The set cannot be |
| • Batteries are worn out. Replace with new batteries. |
| 116 |
operated with the |
| • Operate the remote control unit within a distance of | about | 116 |
remote control unit. |
| 23 ft/7 m from this unit and at an angle of within 30°. |
|
|
|
| • Remove any obstacle between this unit and the remote control | 116 | |
|
| unit. |
|
|
|
| • Insert the batteries in the proper direction, checking the q and | 116 | |
|
| w marks. |
|
|
|
| • The set’s remote control sensor is exposed to strong light (direct | 116 | |
|
| sunlight, inverter type fluorescent bulb light, etc.). Move the set |
| |
|
| to a place in which the remote control sensor will not be exposed |
| |
|
| to strong light. |
|
|
|
| • The ZONE SELECT setting is not correct. Press ZONE SELECT to | 105 | |
|
| select the zone to operate. |
|
|
|
| • The operation mode does not match the settings of the device to | 105 | |
|
| operate. Check the operation mode. |
|
|
|
|
|
|
|
Perform this procedure if the display is abnormal or if operations cannot be performed. When the microprocessor is reset, all the settings are reset to their default values.
| ON/STANDBY | PRESET CHANNEL 2 |
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 Turn off the power using ON/STANDBY.
2 Press ON/STANDBY while simultaneously pressing PRESET CHANNEL 2 and
PRESET CHANNEL 3.
3 Once the display starts flashing at intervals of about 1 second, release the two buttons.
If in step 3 the display does not flash at intervals of about 1 second, start over from step 1.
version Basic
version Advanced
Information
129