Directed Electronics Ready Remote - page 50

46 © 2006 Directed Electronics

3. PPrrooggrraamm..Within 10-seconds, press and hold the

button on the transmitter, until the parking lights turn off

and then back on. Now release the button. Repeat

this step within 10-seconds of programming a transmitter to

program additional transmitters to your system.

4. EExxiitt LLeeaarrnn MMooddee..After programming the transmitter, wait

10-seconds, the parking lights will turn off. Programming

transmitter(s) is now complete.

important: When programming a remote ensure to hold the

remote about 4-feet away from the Directed unit. If the

remote is too close to the unit, the remote may not program.

note: A second remote can only be added to the system

immediately after programming the first remote.

PROG

PROG

ARM

ARM

DISARM

DISARM

PROG

PROG

ARM

ARM

DISARM

DISARM

note: The system can only learn, after being connected and

with the FIRST IGNITION ON. If not learned with the

first ignition on the main power fuses will have to be dis-

connected from the READY REMOTE unit and then

reconnected and the procedure repeated.

Contents

Main Page i lliimmiitteedd lliiffeettiimmee ccoonnssuummeerr wwaarrrraannttyy ii ttaabbllee ooff ccoonntteennttss Page wwhhaatt iiss iinncclluuddeedd iinnssttaallllaattiioonn ttoooollss iimmppoorrttaanntt iinnffoorrmmaattiioonn system maintenance fcc/id notice wwaarrnniinngg!! ssaaffeettyy ffiirrsstt Page Page mmaaiinn hhaarrnneessss ((HH11)),, 88--ppiinn ccoonnnneeccttoorr sseeccoonnddaarryy hhaarrnneessss ((HH22)),, 77--ppiinn ccoonnnneeccttoorr rreellaayy hheeaavvyy ggaauuggee wwiirreess uussiinngg LLEEDD tteesstt pprroobbee iinnssttaallllaattiioonn 12 wwiirriinngg qquuiicckk rreeffeerreennccee gguuiiddee step 1 step 2 Page Page step 3 Page Page step 4 Page Page step 5 Page Page step 6 TTyyppee AA::Three-wire (+) pulse controlling factory lock relays. TTyyppee BB::Three-wire (-) pulse controlling factory lock relays. TTyyppee EE:: Electrically-activated vacuum systems. The vehicle TTyyppee CC::Direct-wired reversing-polarity switches. The switch- TTyyppee DD:: Adding one or more aftermarket actuators. These TTyyppee FF::One-wire system - cut to lock, ground to unlock. This TTyyppee GG::Positive (+) multiplex. This system is most common- TTyyppee HH:: Negative (-) multiplex. The system is most common- directly to the lock motors. type A: positive-triggered, relay-driven system H2/2 H2/3 H2/4 H2/5 H2/6 H2/7 30 type B: negative-triggered, relay-driven system H2/2 H2/3 H2/4 H2/5 H2/6 H2/7 Page HH22//22 WWHHIITTEE//BBLLAACCKK:: Once both door lock wires are HH22//33 GGRREEEENN//BBLLAACCKK:: Connect the green/black wire to HH22//44 VVIIOOLLEETT//BBLLAACCKK::This wire must be connected to HH22//55 BBRROOWWNN//BBLLAACCKK::Connect the brown/black wire to HH22//66 BBLLUUEE//BBLLAACCKK:: Connect the blue/black wire to the HH22//77 VVIIOOLLEETT:: This wire must be connected to a constant 34 type D: adding one or more after-market actuators H2/2 H2/3 H2/4 H2/5 H2/6 H2/7 35 type E: electrically-activated vacuum H2/2 H2/3 H2/4 H2/5 H2/6 H2/7 36 type F: one-wire system (cut to lock, ground to unlock) CUT CUT H2/2 H2/3 H2/4 H2/5 H2/6 H2/7 Page Page Page step 7 Page step 8 Page step 9 step 10 Page step 11 48 rreemmoottee ffuunnccttiioonnss The receiver uses a computer-based learn routine to learn the remote buttons. standard configuration Press the button to lock the vehicle. Press the button to unlock the vehicle. Press the button twice to remote start the vehicle. Press the button twice to remote stop the vehicle. Buttons Buttons and ccoonnttrrooll mmoodduullee pprrooggrraammmmiinngg Page Page uussiinngg yyoouurr ssyysstteemm warning! safety first Page locking with remote unlocking with remote ignition-controlled door locks remote start Page timer mode ppiitt ssttoopp mmooddee ttrruunnkk//aauuxxiilliiaarryy ccooddee hhooppppiinngg rree--ssyynncchhrroonniizzee ttrroouubblleesshhoooottiinngg Page gglloossssaarryy ooff tteerrmmss nnootteess Page QUICK REFERENCE GUIDE: The company behind this system is Directed Electronics