3. Projecting an Image

8.Use the SELECT ￿￿￿￿ button to select another icon which points in the direction.

Screen

On the Cornerstone adjustment screen, select “Exit” and then “OK”, or press the CANCEL but- ton on the remote control.

The confirmation screen is displayed.

9.Press the SELECT ￿ or ￿ button to highlight the [OK] and press the ENTER button.

b Optimizing RGB Picture Automatically

Adjusting the Image Using Auto Adjust

Optimizing RGB image automatically

Press the Auto Adjust button to optimize an RGB image automatically.

[Poor picture]

 

 

 

MENU

 

 

 

 

 

 

 

 

 

3D

A

 

 

 

SELECT

 

3D REFORM AUTO ADJUST

 

E

 

 

 

L

 

 

 

N

 

 

 

E

 

 

 

T

 

 

C

ON/STAND BY

 

 

E

R

N

 

 

 

CA

 

 

 

 

LAMP 2

 

STATUS POWER

 

 

 

 

 

 

JKL

MNO

PQR

 

 

 

 

 

4

5

6

 

 

 

 

 

STU

VWX

YZ /

 

 

 

 

 

7

8

9

[Normal picture]

 

 

 

 

,.

UNDO

CANCEL

 

 

 

 

0

 

 

 

 

 

 

TEST

INFO.

HELP

 

 

 

 

POSITION

PIXEL

AUTO

 

 

 

 

LENS

 

 

 

 

This completes the keystone correction.

Selecting “Cancel” will return to the adjustment screen without saving changes (Step 3).

Selecting "Reset" will return to the factory default. Selecting "Undo" will exit without saving changes.

NOTE: To return the 3D Reform correction setting values to the factory default, press and hold the 3D REFORM button on the projector cabinet or the KEYSTONE button on the remote control for a minimum of 2 seconds.

NOTE: During 3D Reform adjustment, "Aspect Ratio" and "Screen" may not be avail- able. Should this happen, first reset the 3D Reform data and then do each setting. Second repeat the 3D Reform adjustment. Changing Aspect Ratio and/or Screen setting can limit 3D Reform in its adjustable range.

The adjustable ranges for 3D Reform are as follows:

Horizontal

Max ±30° approx.

Vertical

Max ±40° approx.

*The following are conditions at the above maximum angle when all of the following are met

Image is projected in Wide (Zoom)

The lens is positioned at the center (when not, adjustable range in- creases or decreases)

Resolution is XGA

Higher resolution than XGA limits 3D Reform in its adjustable range.

Menu items should be set as follows:

Aspect Ratio

1.33:1 (4:3)

Screen Type

1.33:1 (4:3)

Horizontal and Vertical are adjusted separately.

A combination of both adjustments limits 3D Reform in its adjustable range.

When “Native” is selected in “Resolution”, “3D Reform” is not available.

Press the AUTO ADJUST or AUTO button to fine-tune the computer im- age or to remove any vertical banding that might appear and to reduce video noise, dot interference or cross talk (this is evident when part of your image appears to be shimmering). This function adjusts the clock frequen- cies that eliminate the horizontal banding in the image. This function also adjusts the clock phase to reduce video noise, dot interference or cross talk. (This is evident when part of your image appears to be shimmering.) This adjustment may be necessary when you connect your computer for the first time.

NOTE:

Some signals may not be displayed correctly or take time.

The Auto Adjust function does not work for component and video signal.

If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock and Phase manually. See page 8-10.

n Turning Up or Down Volume

Sound level from the speaker and the AUDIO OUT jack (RCA) on the projector can be adjusted.

-

+

increase volume

 

 

 

decrease volume

NOTE: The SELECT ￿ or ￿ button works as a volume control only when no menu appears.

Volume bar

NOTE: The volume bar can be dis- played by selecting “Sound” from “Ba- sic Menu” or “Advanced Menu”.

3-6

Page 38
Image 38
Dukane 9060 user manual Optimizing RGB Picture Automatically, Turning Up or Down Volume