3. Projecting an Image
This chapter describes how to turn on the projector and to project a pic- ture onto the screen.
z Turning on the Projector
NOTE:
•When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off[O] position. Failure to do so may cause damage to the projector.
•The projector has two power switches: main power switch and POWER button (POWER ON and OFF on the remote control)
•The projector has a feature to prevent itself from being used by unauthorized individuals. To use this feature, register your PC card as a protect key. See "Secu- rity" in "Projector Options" on page
To turn on the main power to the projector, press the Main Power switch to the ON posi- tion ( I ).
Standby or Idle | Flashing for 1 | Steady light |
| minute. |
|
POWER | POWER | POWER |
| ON/STAND BY |
|
Steady orange | Flashing green | Steady green |
light | light | light |
Before you turn on your projector, ensure that the computer or video source is turned on and that your lens hood cap is removed.
Only after you press the ON/STAND BY button on the projector cabinet or POWER ON button on the remote control for a minimum of 2 seconds will the power indicator turn to green and the projector become ready to use.
|
|
| MENU |
|
|
|
|
|
|
|
| 3D | A |
|
| SELECT |
| 3D REFORM AUTO ADJUST | ||
|
|
|
|
| ||
E |
|
|
| L |
|
|
N |
|
|
| E |
|
|
T |
|
| C | ON/STAND BY |
| |
| E | R | N |
| ||
|
| CA |
|
|
| |
LAMP 2 |
| STATUS | POWER |
| ||
NOTE: You cannot turn off the projector for 60 seconds immediately after turning on the projector.
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup screen. This screen gives you the opportunity to select one of the seven menu lan- guages: English, German, French, Italian, Spanish, Swedish and Japa- nese.
To select a menu language, follow these steps:
1.Use the SELECT or button to select one of the seven languages for the menu.
|
|
| MENU |
|
|
|
|
|
|
|
| 3D | A |
|
| SELECT |
| 3D REFORM AUTO ADJUST | ||
E |
|
|
| L |
|
|
N |
|
|
| E |
|
|
T |
|
| C | ON/STAND BY |
| |
| E | R | N |
| ||
|
| CA |
|
|
| |
LAMP 2 |
| STATUS | POWER |
| ||
2. Press the ENTER button to execute the selection.
|
|
| MENU |
|
|
|
|
|
|
|
| 3D | A |
|
| SELECT |
| 3D REFORM AUTO ADJUST | ||
E |
|
|
| L |
|
|
N |
|
|
| E |
|
|
T |
|
| C | ON/STAND BY |
| |
| E | R | N |
| ||
|
| CA |
|
|
| |
LAMP 2 |
| STATUS | POWER |
| ||
3. The Basic menu will be displayed in the language you have selected.
To close the menu, press the CANCEL button.
|
|
| MENU |
|
|
|
|
|
|
|
| 3D | A |
|
| SELECT |
| 3D REFORM AUTO ADJUST | ||
E |
|
|
| L |
|
|
N |
|
|
| E |
|
|
T |
|
| C | ON/STAND BY |
| |
| E | R | N |
| ||
|
| CA |
|
|
| |
LAMP 2 |
| STATUS | POWER |
| ||
After this has been done, you can proceed to the advanced menu opera- tion.
If you want, you can select the menu language later. See "Language" on page
NOTE: To turn the projector on by plugging in the power cable, first turn on the Main Power switch to ON and use the menu and enable the "Auto Start" feature. (See page
• If one of the following things happens, the projector will not turn on.
*If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's internal components to cool down.
*When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp.
*If the lamp fails to light, and if the LAMP indicator 1 or 2 flashes on and
off in a cycle of six times, wait a full minute and then turn on the power.
