Command | parameter | Function |
Nop | | | -no operation |
End | | | -ending the running sequence |
Out | X.Y set | | -Output Y (1 ..4) of the I/O module X (A..D) is set to 1 (contact closed) |
| X.Y clr | | -Output Y (1 ..4) of the I/0 module X (A..D) is set to 0 (contact open) |
| X.Y inv | | -Output Y (1 ..4) of the I/O module X (A..D) is inverted |
Start | Axx | | -ends a currently running audio signal immediately and starts the alarm preset xx |
| Gxx | | -ends a currently running audio signal immediately and starts the gong preset xx |
| Mxx | | -ends a currently running audio signal immediately and starts the message xx |
| Ann. | | -ends a currently running audio signal immediately and starts the announcement |
Break | | | -ends a currently running audio signal immediately |
Finish | | | -requests the end of the running audio signal. Gong, alarm fade out, messages and |
| | | announcements are finished, recording is stopped. |
DMM= | -xx dB | | -controls of the DMM 4650 audio signal is set to -xx dB (*0 dB default) |
Sum= | -xx dB | | -control of the input - output XLR connection is set to -xx dB |
Bypass | set | | -analog bypass relay, direct connection XLR input - output closed |
| clr | | -analog bypass relay, no relay connection XLR input - output |
| inv | | -inverted analog bypass relay |
Audio | prl | | -switches the started DMM audio signals to pre-listen outputs (Pre-Listen only) |
| sum | | -switches the started DMM audio signals to pre-listen and sum outputs (*default) |
Record | Mxx | | -ends a currently running audio signal immediately and starts the recording of the |
| | | message xx. At first this message is being erased and then recording starts at the last |
| | | adjusted recording level. Audio quality and name of this message stay unchanged. |
| | | The message priority is identical with the sequence priority. The execution time lasts |
| | | until End Delete Message (start of recording). |
Dly= | ttt,t s | | -sets a timer to ttt,t seconds and starts measuring this time (sand glass). |
Count= | xxxx | | -sets a counter (event counter) to a starting value xxxx. With every “if count”-command |
| | | the counter is decremented by 1 until 0 is reached. |
Jump | xx | | -resumes the sequence at step number xx. |
if | Delay | | -only executes the next step number if the delay time has elapsed (see command Dly). |
| | | Otherwise the next step number is being skipped. |
| Count | | -the counter is decremented by 1. The next step number is executed only if the counter |
| | | has reached 0 (see command Count). If the counter value is greater than 0, the next |
| | | step number is being skipped. |
| Audio | | -executes the next step number only if the audio signal started at last is finished |
| | | (see command start), otherwise the next step number is being skipped. |
| In X,Y | Z | -executes the next step number only if the desired level Z (H or L) is applied at input |
| | | Y (1 ..4) of the I/O module X (A..D). If this condition is not fulfilled, the next step number |
| | | is being skipped. |
| Stop | | -executes the next step number only if the stop trigger condition of this sequence is |
| | | fulfilled. Otherwise the next step number is being skipped. |
wt | Delay | | -waits until the delay time is elapsed |
| Audio | | -waits until the last started audio signal is finished |
| In X,Y | Z | -waits until the desired level Z (H or L) is applied at input Y (1 ..4) of the I/O |
| | | module X (A..D). |
| Stop | | -waits until the stop trigger condition of this sequence is fulfilled. |
