Operation, Overview, Display, Menu Tree | Emerson 3081FG specs

Model 3081FG

Instruction Manual

IB-106-3081 Rev. 1.5 September 2002

3-4 OPERATION

a.Overview

This section explains the operator controls and displays of the Two-Wire In Situ Oxy- gen Analyzer. The use of the Infrared Re- mote Control (IRC) and the Model 3081 Transmitter Liquid Crystal Display (LCD) are described in detail. HART/AMS operation is not covered here but is discussed in Section 4, HART/AMS.

b.Display

The Model 3081 Transmitter LCD displays the O2 concentration, cell temperature, and

4-20 mA output current during normal op- eration (see Figure 3-4). The LCD will also display fault conditions when they occur. To interact with the transmitter, use the IRC and navigate through a series of menus displayed on the LCD.

c. Menu Tree

	The screens that can be displayed are	3
	shown in the menu tree of Figure 3-5.	3
	shown in the menu tree of Figure 3-5.
	These screens are displayed on the LCD
	and are accessed using the IRC keypad.

CIRCUIT

END

TERMINAL

END

MODEL 3081 TRANSMITTER

ELECTRONICS HOUSING

%

mA

26020031

Figure 3-4. Normal Operation Display

Rosemount Analytical Inc. A Division of Emerson Process Management

Startup and Operation 3-3

Image 33

Emerson 3081FG instruction manual Operation, Overview, Display, Menu Tree, Circuit END Terminal

Contents

Model 3081FG Essential Instructions Highlights of Changes Page Model 3081FG Table of Contents Proper Calibration Check Gas Flow Rate List of Illustrations Model 3081 Transmitter Terminal Block List of Tables Model 3081FG Definitions Preface Model 3081FG Component Checklist of Typical System Package Contents Section Description and Specifications Code Mounting Adapter Stack Side Product Matrix System Overview System ConfigurationScope System Description System Features Handling the Analyzer System Considerations Transmitter Typical System Installation Probe Specifications Ohms Lift OFF Maximum Power Supply VoltageVDC Operating Load Region PRE-INSTALLATION Section InstallationMechanical Installation Inspect Side View Bottom View Front View Metal Wall Masonry Wall Stack or Duct Horizontal Probe Installation Adjusting Probe Insertion Depth Model 3081FG Installing Model 3081 Transmitter Circuit Terminal END Cover LockBlock TB Mounting Holes Electrical Installation Display Positioning Assembly Model 3081 Transmitter 4-20 mA and Signal Connections Terminal Block ConduitThermocouple CELL-WH CELL+BK Reference Air Package Pneumatic InstallationInstrument Air Reference Air Calibration Check Gas Outlet Outlet ConnectionInlet Connection Flow SET MAX Point Knob Mounting Holes Power UP Section Startup and OperationGeneral Proper Calibration Check Gas Flow Rate Reestablishing Proper Calibration Check GAS Flow Rate Overview OperationDisplay Menu Tree Calcheck DiagnosticsMenu Program Navigation Infrared Remote Control IRC Analyzer Access Code O2 Concentration Analyzer Access Code Or SecurityProgram Menu O2 Concentration O2 Concentration Upper Cell Temperature Fault Value O2 Concentration Indicator Fault ValueUpper Range VAL Cell T HI To Reset Maximum Cell Temperature Reset MAX Cell TO2 Concentration Analyzer Access Code SET O2 Filter Time SET HI Bottle O2 SET LO Bottle O2Concentration Parameter Range Default Model 3081 Transmitter ParametersModel 3081 Transmitter Parameters SET Code Diagnostics Menu Show FaultC mV 24. Previous Slope Previous Constant 23. Cell Impedance SW Build Number SW Build DateCalcheck Menu Accept LOW O2 27. in MANUAL? 29. Accept LOW O2 Slope Model 3081FG Section HART/AMS Hart Communicator Signal LineOverview Connections Method 2, For Load Resistance 250 Ohms Analog Output Device Loop Connectors Hart Communicator PC TWO-WIRE in Situ Oxygen AnalyzerOFF-LINE and ON-LINE Operations Menu Tree for Hart Communicator Device Setup From Sheet Basic Setup Detailed From Sheet Signal Condition Detailed Setup Output Hart Communicator Start CAL- Check Method Model 3081FG Model 3081 Electronics Replacement Section Maintenance and ServiceDisplay Board Replacement PC Board Stack Replacement Two-Wire In Situ Oxygen Analyzer Exploded View Oxygen Probe Replacement Oxygen Probe Terminal Block Section Troubleshooting Probe LifeIMPEDANCE, Ω Fault Indications OfresponseSpeed Thermocouple Identifying and Correcting Fault Indications Fault 1, Open Thermocouple Fault 3, Shorted Thermocouple Fault 5, O2 Cell Open Fault 6, Cell Impedance Too High Fault 5, O2 Cell Open 11. Fault 7, Reversed O2 Cell Fault 7, Reversed O2 Cell Model 3081FG Section Return of Material Model 3081FG Replacement Parts List Replacement PartsSection Index No Part Number Description Model 3081FG Section Index Model 3081FG Model 3081FG Page Section Drawings and Schematics Model 3081FG Warranty Two-Wire In Situ Oxygen Analyzer Serial no Order no