Manuals / Emerson / Personal Care / Oxygen Equipment

Emerson ib-106-340cdr instruction manual Calibration Components, Part Number Description

Models: ib-106-340cdr oxymitterdr hazardous area in-siu oxygen probe

1 66

Download 66 pages 8.96 Kb

Page 22

Instruction Manual

IB-106-340CDR Original Issue January, 2002

Hazardous Area Oxymitter DR

Table 1-2.		Calibration Components

Part
Number		Description
1A99119G01	Two disposable calibration gas bottles — 0.4%
	and 8%	O2, balance nitrogen — 550 liters each*
1A99119G02	Two flow regulators for calibration gas bottles

1A99119G03	Bottle rack

*Calibration gas bottles cannot be shipped via airfreight.

1-8 Description and Specifications

Rosemount Analytical Inc. A Division of Emerson Process Management

Image 22

Emerson ib-106-340cdr, oxymitterdr hazardous area in-siu oxygen probe Calibration Components, Part Number Description

Contents

Oxymitter DR Essential Instructions Table of Contents Hazardous Area Oxymitter DR List of Illustrations List of Tables Preface Definitions Hazardous Area Oxymitter DR Section I. Identification Section II. Physical Data Section V. Health Hazard Data Section VI. Reactivity Data Section VII. Spill or Leak Procedures Section IX. Special Precautions Hazardous Area Oxymitter DR Technical Support Hotline Component Checklist of Typical System Package Contents Section Description and SpecificationsSystem Overview System Configuration System Features Typical System Installation Flame Arrestor Snubber Diffusion Assembly Abrasive Shield AssemblyFlame Arrestor Ceramic Diffusion Assembly Upgrading the Hazardous Area Oxymitter DR View a View B Specifications Product Matrix Code Sensing Probe Type Calibration Components Part Number Description Installation Section InstallationMechanical Installation Selecting Location Hazardous Area Oxymitter DR Installation Hazardous Area Oxymitter DR with Abrasive Shield Mounting Plate Outline With Abrasive Shield Without Abrasive Shield Orienting the Optional Vee Deflector Electrical Installation Connect O2 and Heater Thermocouple Signals Pneumatic Installation System Setup Overview Setup 132 Analog Electronics Westinghouse Model 218A ELEC- Tronics Setup G02 G04 Westinghouse Model TC200 VERI- Trim Electronics Setup 11. Main PCB Model TC200 Eprom Replacement Westinghouse Model 132 Digital Electronics Setup 12. Main PCB Model 132 Eprom Replacement World Class 3000 Intelligent Field Transmitter Setup 14. Heater Power Supply HPS 3000 Jumper Configuration Yokogawa ZA8C and AV8C Converter Electronics Setup 15. DR Probe Wired to the ZA8C or a V8C Converter Section Startup and Operation General Hazardous Area Oxymitter DR Overview Section Maintenance and ServiceHazardous Area Oxymitter DR Replacement Calibration Hazardous Area Oxymitter DR Exploded View Install Terminal Block Replacement Entire Probe Replacement Heater Strut Replacement Heater Strut Assembly Cell Replacement 22220028 Replacement Procedure Ceramic Diffusion Element ReplacementThis refers to the ceramic diffusion element only General Ceramic Diffusion Element Replacement Also, do not get any cement onto the flame arrestor element Termination Housing Wiring Termination Housing Connections Hazardous Area Oxymitter DR Probe Troubleshooting Section TroubleshootingSymptom Check Fault Remedy Hazardous Area Oxymitter DR Section Return of Material Equipment Return Hazardous Area Oxymitter DR Section Replacement Parts Replacement Parts for Probe Cell Replacement Kit BY-PASS Packages Section Optional AccessoriesO2 Calibration GAS Sequencer Hazardous Area Oxymitter DR Section Appendices Appendix A. Updating DR Oxymitter to Full Oxymitter Hazardous Area Oxymitter DR Upgrade Procedure Figure A-1. Component Replacement Figure A-2. Terminal Block and Wiring Section Index Hazardous Area Oxymitter DR Warranty Hazardous Area Oxymitter DR Serial no Order no