Manuals / Brands / Personal Care / Oxygen Equipment / Emerson / Personal Care / Oxygen Equipment

Emerson ib-106-340cdr, oxymitterdr hazardous area in-siu oxygen probe SECTION 3 STARTUP AND OPERATION

1 66

Download 66 pages, 2.08 Mb

Instruction Manual

IB-106-340CDR Original Issue

January, 2002

Rosemount Analytical Inc. A Division of Emerson Process Management Startup and Operation 3-1

Hazardous Area Oxymitter DR

SECTION 3STARTUP AND OPERATION

Install all protective equipment covers

and safety ground leads before

equipment startup. Failure to install

covers and ground leads could result

in serious injury or death.

3-1 GENERAL

For startup and operation instructions, refer to

the Instruction Bulletin provided with your elec-

tronics package.

Contents

Main ESSENTIAL INSTRUCTIONS READ THIS PAGE BEFORE PROCEEDING! TABLE OF CONTENTS LIST OF ILLUSTRATIONS LIST OF TABLES PREFACE DEFINITIONS NOTE TO USERS IMPORTANT SAFETY INSTRUCTIONS FOR THE WIRING AND INSTALLATION OF THIS APPARATUS SECTION I. IDENTIFICATION SECTION II. PHYSICAL DATA SECTION III. HAZARDOUS INGREDIENTS SECTION IV. FIRE AND EXPLOSION DATA SECTION V. HEALTH HAZARD DATA THRESHOLD LIMIT VALUE EFFECTS OF OVER EXPOSURE EXPOSURE TO USED CERAMIC FIBER PRODUCT SPECIAL TOXIC EFFECTS SECTION VI. REACTIVITY DATA STABILITY/CONDITIONS TO AVOID HAZARDOUS POLYMERIZATION/CONDITIONS TO AVOID SECTION VII. SPILL OR LEAK PROCEDURES SECTION VIII. SPECIAL PROTECTION INFORMATION SECTION IX. SPECIAL PRECAUTIONS PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING CONCENTRATION Page Page SECTION 1 DESCRIPTION AND SPECIFICATIONS Page Page Page VIEWA VIEWB A A B B Page Table 1-1. Product Matrix Page SECTION 2 INSTALLATION 2-2 Installation Rosemount Analytical Inc. A Division of Emerson Process Management AMBIENTWEATHER CONDITIONS Figure 2-1. Hazardous Area Oxymitter DR Installation INSULATE IF EXPOSEDTO PROCESS FLOW MUST BE IN THIS DIRECTIONWITH RESPECT TO DEFLECTOR 3534B48G01 THESE FLAT FACED FLANGES ARE MANUFACTUREDTO ANSI, DIN, & JIS BOLT Rosemount Analytical Inc. A Division of Emerson Process Management Installation 2-3 Figure 2-2. Hazardous Area Oxymitter DR with Abrasive Shield 2-4 Installation Rosemount Analytical Inc. A Division of Emerson Process Management MOUNTING PLATE OUTLINE Figure 2-3. Hazardous Area Oxymitter DR Adapter Plate Dimensions Rosemount Analytical Inc. A Division of Emerson Process Management Installation 2-5 INSTALLATION FOR MASONRY WALL STACK CONSTRUCTION INSTALLATION FOR METAL WALL STACK OR DUCT CONSTRUCTION WITHOUT ABRASIVE SHIELD WITH ABRASIVE SHIELD Figure 2-4. Hazardous Area Oxymitter DR Adapter Plate Installation Page Page ! Page Page Page Page Page 2-14 Installation Rosemount Analytical Inc. A Division of Emerson Process Management MAINPCB Figure 2-12. Main PCB (Model 132) EPROM Replacement OFF ON EPROM P0022 Figure 2-14. Heater Power Supply (HPS 3000) Jumper Configuration 2-16 Installation Rosemount Analytical Inc. A Division of Emerson Process Management Figure 2-15. DR Probe Wired to the ZA8C or A V8C Converter ZA8C OR AV8C CONVERTER SECTION 3 STARTUP AND OPERATION Page SECTION 4 MAINTENANCE AND SERVICE Figure 4-1. Hazardous Area Oxymitter DR Exploded View Page Page Page Page Page Page Page Page SECTION 5 TROUBLESHOOTING Page SECTION 6 RETURN OF MATERIAL Page SECTION 7 REPLACEMENT PARTS 7-2 Replacement Parts Rosemount Analytical Inc. A Division of Emerson Process Management Figure 7-1. Cell Replacement Kit Figure 7-2. Probe Disassembly Kit SECTION 8 OPTIONAL ACCESSORIES Page Page Page APPENDIX A UPGRADING HAZARDOUS AREA OXYMITTER DR TO FULL HAZARDOUS AREA OXYMITTER A Page SECTION 10 INDEX Page WARRANTY