Cell Replacement Kit | Emerson ib-106-340cdr instruction

Instruction Manual

IB-106-340CDR Original Issue January, 2002

Hazardous Area Oxymitter DR

ANSI

GASKET

WIRE AND

PAD ASSEMBLY

ANTI-SEIZE

COMPOUND

PROBE TUBE

(NOT INCLUDED

IN KIT)22 GA.

WIRE

	CORRUGATED
	SEAL	CLOSED END
	CELL AND	CONNECTOR
	CELL AND
	FLANGE	SET SCREWS
	ASSEMBLY	SET SCREWS
	ASSEMBLY
	SOCKET HEAD	TEFLON
	SOCKET HEAD	TUBING
	CAP SCREWS

CALIBRATION GAS

PASSAGE

35830009

Figure 7-1. Cell Replacement Kit

HEX KEYS

SPANNER

WRENCH

ANTI-SEIZE

COMPOUND

PHILIPS

SCREWDRIVER

WRENCH

TUBE INSERTION

TUBE

35830010

Figure 7-2. Probe Disassembly Kit

7-2 Replacement Parts

Rosemount Analytical Inc. A Division of Emerson Process Management

Image 56

Emerson ib-106-340cdr, oxymitterdr hazardous area in-siu oxygen probe instruction manual Cell Replacement Kit

Contents

Oxymitter DR Essential Instructions Table of Contents Hazardous Area Oxymitter DR List of Illustrations List of Tables Preface Definitions Hazardous Area Oxymitter DR Section I. Identification Section II. Physical Data Section V. Health Hazard Data Section VI. Reactivity Data Section VII. Spill or Leak Procedures Section IX. Special Precautions Hazardous Area Oxymitter DR Technical Support Hotline System Overview Section Description and SpecificationsComponent Checklist of Typical System Package Contents System Configuration System Features Typical System Installation Abrasive Shield Assembly Flame Arrestor Ceramic Diffusion AssemblyFlame Arrestor Snubber Diffusion Assembly Upgrading the Hazardous Area Oxymitter DR View a View B Specifications Product Matrix Code Sensing Probe Type Calibration Components Part Number Description Section Installation Mechanical InstallationInstallation Selecting Location Hazardous Area Oxymitter DR Installation Hazardous Area Oxymitter DR with Abrasive Shield Mounting Plate Outline With Abrasive Shield Without Abrasive Shield Orienting the Optional Vee Deflector Electrical Installation Connect O2 and Heater Thermocouple Signals Pneumatic Installation System Setup Overview Setup 132 Analog Electronics Westinghouse Model 218A ELEC- Tronics Setup G02 G04 Westinghouse Model TC200 VERI- Trim Electronics Setup 11. Main PCB Model TC200 Eprom Replacement Westinghouse Model 132 Digital Electronics Setup 12. Main PCB Model 132 Eprom Replacement World Class 3000 Intelligent Field Transmitter Setup 14. Heater Power Supply HPS 3000 Jumper Configuration Yokogawa ZA8C and AV8C Converter Electronics Setup 15. DR Probe Wired to the ZA8C or a V8C Converter Section Startup and Operation General Hazardous Area Oxymitter DR Section Maintenance and Service Hazardous Area Oxymitter DR ReplacementOverview Calibration Hazardous Area Oxymitter DR Exploded View Install Terminal Block Replacement Entire Probe Replacement Heater Strut Replacement Heater Strut Assembly Cell Replacement 22220028 This refers to the ceramic diffusion element only General Ceramic Diffusion Element ReplacementReplacement Procedure Ceramic Diffusion Element Replacement Also, do not get any cement onto the flame arrestor element Termination Housing Wiring Termination Housing Connections Hazardous Area Oxymitter DR Symptom Check Fault Remedy Section TroubleshootingProbe Troubleshooting Hazardous Area Oxymitter DR Section Return of Material Equipment Return Hazardous Area Oxymitter DR Section Replacement Parts Replacement Parts for Probe Cell Replacement Kit O2 Calibration GAS Sequencer Section Optional AccessoriesBY-PASS Packages Hazardous Area Oxymitter DR Section Appendices Appendix A. Updating DR Oxymitter to Full Oxymitter Hazardous Area Oxymitter DR Upgrade Procedure Figure A-1. Component Replacement Figure A-2. Terminal Block and Wiring Section Index Hazardous Area Oxymitter DR Warranty Hazardous Area Oxymitter DR Serial no Order no