Emerson RTM-ATCA-F120-OPT Conventions

RTM-ATCA-F120-OPT Installation and Use (6806800G29C)

About this Manual

10

About this Manual

Conventions

The following table describes the conventions used throughout this manual.

NEBS Network Equipment-Building System

PCB Printed Circuit Board

PICMG PCI Industrial Computer Manufacturers Group

PMC P CI Mezzanine Card

RTM Rear Transition Module

RoHS Restriction of Hazardo us Substa nces Dire ctive

SELV Safety Extra Low Voltage Circuits

STP Shielded Twisted Pair

Abbreviation Description

Notation Description

0x00000000 Typical notation for hexadecimal numbers (digits are

0 through F), for example used for addresses and

offsets

0b0000 Same for binary numbers (digits are 0 and 1)

bold Used to emphasize a word

Screen Used for on-screen output and code related elements

or commands in body text

Courier + Bold Used to characterize user input and to separate it

from system output

Reference Used for references and for table and figure

descriptions

File > Exit Notation for selecting a submenu

<text> Notation for variables and keys

[text] Notation for software buttons to click on the screen

and parameter description

... Repeated item for example node 1, node 2, ..., node

12

Contents

Main Trademarks Notice Limited and Restricted Rights Legend Contact Address Contents Page List of Tables Page List of Figures Page About this Manual Overview of Contents Abbreviations Conventions The following table describes the conventions used throughout this manual. Summary of Changes This manual has been revised and replaces all prior editions. Page Safety Notes Electrical Interference Safety Notes Operation Installation Safety Notes SFP/SFP+ Modules Environment Sicherheitshinweise EMV Operation Installation SFP/SFP+ Modules Umweltschutz Chapter 1 Introduction 1.1 Features Page Introduction 1.2 Standard Compliances For Declaration of Conformity refer, RTM Declaration of Conformity.. This RTM-ATCA-F120-OPT meets the following standards. Table 1-1 Standard Compliances Page Chapter 2 Hardware Preparation and Installation 2.1 Overview 2.2 Unpacking and Inspecting the RTM 2.3 Environmental and Power Requirements 2.3.1 Environmental Requirements 2.3.2 Power Requirements The RTM has a typical power dissipation of 22W, and a maximum power dissipation of 30W. Table 2-1 Environmental Requirements 2.4 Installing and Removing the RTM 2.4.1 Installing the RTM Page Page Page Page 2.4.2 Removing the RTM Page 2.5 Installing and Removing SFP/ SFP+ Modules Page Page Page Page Page Controls, LEDs and Connectors 3.2 LEDs and Interface Connectors The following figure shows the face plate of the RTM. Figure 3-1 Face Plate 3.2.1 LEDs The RTM provides four LEDs at its face plate. Their meaning is described in the following table. 3.2.2 Interface Connectors The RTM provides access to the following interfaces at its face plate. Table 3-1 Face Plate LEDs Page Figure 3-2 Location of Ethernet Fabric Channel Uplink Interfaces Fabric Channel - 1 Gbit Ethernet uplink 3.2.2.1.1 10 GBit Fabric Interface Channel Uplinks 3.2.2.1.2 1 GBit Fabric Interface Uplinks 3.2.2.2 Base Channel Interface Connectors Base interface- 10 GBit Ethernet uplink Base interface - 10 GBit Ethernet uplink 3.2.2.2.1 10 GBit Base Interface Uplinks 3.2.2.2.2 1 GBit Base Interface Uplinks 3.2.2.3 SFP/SFP+ Module Hot Swap 3.2.2.4 Telecom Clocking Connectors CH3 CH2 Page Figure 3-5 Location of Serial Interface Connectors Serial Interface Connector Page Functional Description 4.2 Block Diagram The following figure shows the main functional blocks of the RTM. Figure 4-1 Block Diagram RTM Face Plate Zone 3 Connectors 4.3 Mezzanine Management Controller Table 4-1 IPMI Sensors Overview (continued) The following figure shows the location of the on-board temperature sensors. Table 4-1 IPMI Sensors Overview (continued) Page Page Page Appendix A A.1 Emerson Network Power - Embedded Computing Documents Page Index Page Page HOW TO REACH LITERATURE AND TECHNICAL SUPPORT: