Emerson RTM-ATCA-F120-OPT Operation, Installation

RTM-ATCA-F120-OPT Installation and Use (6806800G29C)

Safety Notes

14

Operation of this equipment in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own expense.Changes or

modifications not expressly approved by Emerson could void the user's authority to operate

the equipment. Board products are tested in a representative system to show compliance with

the above mentioned requirements. A proper installation in a compliant system will maintain

the required performance.Use only shielded cables when connecting peripherals to assure

that appropriate radio frequency emissions compliance is maintained.

Operation

Damage of the RTM

High humidity and condensation on the RTM surface causes short circuits.

Do not operate the RTM outside the specified environmental limits. Make sure the RTM is

completely dry and there is no moisture on any surface before applying power.

Do not operate the RTM below -5°C.

Installation

Damage of the RTM and Additional Devices and Modules

Incorrect installation or removal of additional devices or modules may damage the RTM or the

additional devices or modules.

Before installing or removing additional devices or modules, read the respective

documentation.

Damage of Circuits

Electrostatic discharge and incorrect installation and removal of the RTM can damage circuits

or shorten their life.

Before touching the RTM or electronic components, make sure that your are working in an

ESD-safe environment.

Damage of the RTM

Incorrect installation of the RTM can cause damage of the RTM.

Only use handles when installing/removing the RTM to avoid damage/deformation to the face

plate and/or PCB.

Contents

Main Trademarks Notice Limited and Restricted Rights Legend Contact Address Contents Page List of Tables Page List of Figures Page About this Manual Overview of Contents Abbreviations Conventions The following table describes the conventions used throughout this manual. Summary of Changes This manual has been revised and replaces all prior editions. Page Safety Notes Electrical Interference Safety Notes Operation Installation Safety Notes SFP/SFP+ Modules Environment Sicherheitshinweise EMV Operation Installation SFP/SFP+ Modules Umweltschutz Chapter 1 Introduction 1.1 Features Page Introduction 1.2 Standard Compliances For Declaration of Conformity refer, RTM Declaration of Conformity.. This RTM-ATCA-F120-OPT meets the following standards. Table 1-1 Standard Compliances Page Chapter 2 Hardware Preparation and Installation 2.1 Overview 2.2 Unpacking and Inspecting the RTM 2.3 Environmental and Power Requirements 2.3.1 Environmental Requirements 2.3.2 Power Requirements The RTM has a typical power dissipation of 22W, and a maximum power dissipation of 30W. Table 2-1 Environmental Requirements 2.4 Installing and Removing the RTM 2.4.1 Installing the RTM Page Page Page Page 2.4.2 Removing the RTM Page 2.5 Installing and Removing SFP/ SFP+ Modules Page Page Page Page Page Controls, LEDs and Connectors 3.2 LEDs and Interface Connectors The following figure shows the face plate of the RTM. Figure 3-1 Face Plate 3.2.1 LEDs The RTM provides four LEDs at its face plate. Their meaning is described in the following table. 3.2.2 Interface Connectors The RTM provides access to the following interfaces at its face plate. Table 3-1 Face Plate LEDs Page Figure 3-2 Location of Ethernet Fabric Channel Uplink Interfaces Fabric Channel - 1 Gbit Ethernet uplink 3.2.2.1.1 10 GBit Fabric Interface Channel Uplinks 3.2.2.1.2 1 GBit Fabric Interface Uplinks 3.2.2.2 Base Channel Interface Connectors Base interface- 10 GBit Ethernet uplink Base interface - 10 GBit Ethernet uplink 3.2.2.2.1 10 GBit Base Interface Uplinks 3.2.2.2.2 1 GBit Base Interface Uplinks 3.2.2.3 SFP/SFP+ Module Hot Swap 3.2.2.4 Telecom Clocking Connectors CH3 CH2 Page Figure 3-5 Location of Serial Interface Connectors Serial Interface Connector Page Functional Description 4.2 Block Diagram The following figure shows the main functional blocks of the RTM. Figure 4-1 Block Diagram RTM Face Plate Zone 3 Connectors 4.3 Mezzanine Management Controller Table 4-1 IPMI Sensors Overview (continued) The following figure shows the location of the on-board temperature sensors. Table 4-1 IPMI Sensors Overview (continued) Page Page Page Appendix A A.1 Emerson Network Power - Embedded Computing Documents Page Index Page Page HOW TO REACH LITERATURE AND TECHNICAL SUPPORT: