Manuals / Brands / Computer Equipment / Network Hardware / Emerson / Computer Equipment / Network Hardware

Emerson RTM-ATCA-F120-OPT 2.5 Installing and Removing SFP/ SFP+ Modules

1 68

Download 68 pages, 1.44 Mb

Hardware Preparation and Installation

RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 35

3. Unlatch the upper handle and rotate both handles fully outward.

4. Remove interface cables from face plate connectors, if applicable.

5. Loosen the two RTM face plate screws.

6. Remove the RTM from the slot.

2.5 Installing and Removing SFP/ SFP+ Modules

This section describes how to install and remove SFP and SFP+ modules. For details about

supported SFP/SFP+ modules refer to Interface Connectors on page 43.

Eye Damage

Optical SFP/SFP+ modules may emit laser radiation when no cable is connected.

Avoid staring into open apertures to avoi d damage to your eyes.

Personal Injury and Damage of the RTM and SFP/SFP+ Modules

Installing and using SFP/SFP+ modules which are not fully certified and which do not meet

all relevant safety standards may damage the RTM and the SFP/SFP+ modules and may lead

to personal injury.

Only use and install SFP/SFP+ modules which are fully certified and which meet all relevant

safety standards.

Personal Injury

Optical SFP/SFP+ modules may be classified as laser products. When installing and using any

of these SFP/SFP+ modules, the regulations which correspond to the respective laser class

apply to the whole RTM. Not complying to these regulations, may lead to personal injury.

When installing and using optical SFP/SFP+ modules which are classified as laser products,

make sure to comply to the respective regulations.

Contents

Main Trademarks Notice Limited and Restricted Rights Legend Contact Address Contents Page List of Tables Page List of Figures Page About this Manual Overview of Contents Abbreviations Conventions The following table describes the conventions used throughout this manual. Summary of Changes This manual has been revised and replaces all prior editions. Page Safety Notes Electrical Interference Safety Notes Operation Installation Safety Notes SFP/SFP+ Modules Environment Sicherheitshinweise EMV Operation Installation SFP/SFP+ Modules Umweltschutz Chapter 1 Introduction 1.1 Features Page Introduction 1.2 Standard Compliances For Declaration of Conformity refer, RTM Declaration of Conformity.. This RTM-ATCA-F120-OPT meets the following standards. Table 1-1 Standard Compliances Page Chapter 2 Hardware Preparation and Installation 2.1 Overview 2.2 Unpacking and Inspecting the RTM 2.3 Environmental and Power Requirements 2.3.1 Environmental Requirements 2.3.2 Power Requirements The RTM has a typical power dissipation of 22W, and a maximum power dissipation of 30W. Table 2-1 Environmental Requirements 2.4 Installing and Removing the RTM 2.4.1 Installing the RTM Page Page Page Page 2.4.2 Removing the RTM Page 2.5 Installing and Removing SFP/ SFP+ Modules Page Page Page Page Page Controls, LEDs and Connectors 3.2 LEDs and Interface Connectors The following figure shows the face plate of the RTM. Figure 3-1 Face Plate 3.2.1 LEDs The RTM provides four LEDs at its face plate. Their meaning is described in the following table. 3.2.2 Interface Connectors The RTM provides access to the following interfaces at its face plate. Table 3-1 Face Plate LEDs Page Figure 3-2 Location of Ethernet Fabric Channel Uplink Interfaces Fabric Channel - 1 Gbit Ethernet uplink 3.2.2.1.1 10 GBit Fabric Interface Channel Uplinks 3.2.2.1.2 1 GBit Fabric Interface Uplinks 3.2.2.2 Base Channel Interface Connectors Base interface- 10 GBit Ethernet uplink Base interface - 10 GBit Ethernet uplink 3.2.2.2.1 10 GBit Base Interface Uplinks 3.2.2.2.2 1 GBit Base Interface Uplinks 3.2.2.3 SFP/SFP+ Module Hot Swap 3.2.2.4 Telecom Clocking Connectors CH3 CH2 Page Figure 3-5 Location of Serial Interface Connectors Serial Interface Connector Page Functional Description 4.2 Block Diagram The following figure shows the main functional blocks of the RTM. Figure 4-1 Block Diagram RTM Face Plate Zone 3 Connectors 4.3 Mezzanine Management Controller Table 4-1 IPMI Sensors Overview (continued) The following figure shows the location of the on-board temperature sensors. Table 4-1 IPMI Sensors Overview (continued) Page Page Page Appendix A A.1 Emerson Network Power - Embedded Computing Documents Page Index Page Page HOW TO REACH LITERATURE AND TECHNICAL SUPPORT: