Manuals
/
Brands
/
Computer Equipment
/
Network Hardware
/
Emerson
/
Computer Equipment
/
Network Hardware
Emerson
RTM-ATCA-F120-OPT
Controls, LEDs and Connectors
1
41
68
68
Download
68 pages, 1.44 Mb
Chapter 3
RTM-ATCA-F120-OPT Installation and Use (6806800G29C)
41
Controls, LEDs and Connectors
3.1 Overview
This chapter describes:
z
Face pl ate L EDs
z
Face plate Interface connectors
z
Rear panel connectors
Contents
Main
Trademarks
Notice
Limited and Restricted Rights Legend
Contact Address
Contents
Page
List of Tables
Page
List of Figures
Page
About this Manual
Overview of Contents
Abbreviations
Conventions
The following table describes the conventions used throughout this manual.
Summary of Changes
This manual has been revised and replaces all prior editions.
Page
Safety Notes
Electrical Interference
Safety Notes
Operation
Installation
Safety Notes
SFP/SFP+ Modules
Environment
Sicherheitshinweise
EMV
Operation
Installation
SFP/SFP+ Modules
Umweltschutz
Chapter 1
Introduction
1.1 Features
Page
Introduction
1.2 Standard Compliances
For Declaration of Conformity refer, RTM Declaration of Conformity..
This RTM-ATCA-F120-OPT meets the following standards.
Table 1-1 Standard Compliances
Page
Chapter 2
Hardware Preparation and Installation
2.1 Overview
2.2 Unpacking and Inspecting the RTM
2.3 Environmental and Power Requirements
2.3.1 Environmental Requirements
2.3.2 Power Requirements
The RTM has a typical power dissipation of 22W, and a maximum power dissipation of 30W.
Table 2-1 Environmental Requirements
2.4 Installing and Removing the RTM
2.4.1 Installing the RTM
Page
Page
Page
Page
2.4.2 Removing the RTM
Page
2.5 Installing and Removing SFP/ SFP+ Modules
Page
Page
Page
Page
Page
Controls, LEDs and Connectors
3.2 LEDs and Interface Connectors
The following figure shows the face plate of the RTM. Figure 3-1 Face Plate
3.2.1 LEDs
The RTM provides four LEDs at its face plate. Their meaning is described in the following table.
3.2.2 Interface Connectors
The RTM provides access to the following interfaces at its face plate.
Table 3-1 Face Plate LEDs
Page
Figure 3-2 Location of Ethernet Fabric Channel Uplink Interfaces
Fabric Channel - 1 Gbit Ethernet uplink
3.2.2.1.1 10 GBit Fabric Interface Channel Uplinks
3.2.2.1.2 1 GBit Fabric Interface Uplinks
3.2.2.2 Base Channel Interface Connectors
Base interface- 10 GBit Ethernet uplink Base interface - 10 GBit Ethernet uplink
3.2.2.2.1 10 GBit Base Interface Uplinks
3.2.2.2.2 1 GBit Base Interface Uplinks
3.2.2.3 SFP/SFP+ Module Hot Swap
3.2.2.4 Telecom Clocking Connectors
CH3 CH2
Page
Figure 3-5 Location of Serial Interface Connectors
Serial Interface Connector
Page
Functional Description
4.2 Block Diagram
The following figure shows the main functional blocks of the RTM. Figure 4-1 Block Diagram
RTM
Face Plate
Zone 3 Connectors
4.3 Mezzanine Management Controller
Table 4-1 IPMI Sensors Overview (continued)
The following figure shows the location of the on-board temperature sensors.
Table 4-1 IPMI Sensors Overview (continued)
Page
Page
Page
Appendix A
A.1 Emerson Network Power - Embedded Computing Documents
Page
Index
Page
Page
HOW TO REACH LITERATURE AND TECHNICAL SUPPORT: