Manuals / Brands / Computer Equipment / Network Hardware / Emerson / Computer Equipment / Network Hardware

Emerson RTM-ATCA-F120-OPT The following figure shows the location of the on-board temperature sensors. , Table 4-1 IPMI Sensors Overview (continued)

1 68

Download 68 pages, 1.44 Mb

Functional Description

RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 59

The following figure shows the location of the on-board temperature sensors.

TX Fault SFP01 Other FRU 0x30

TX Fault SFP02 Other FRU 0x31

TX Fault SFP03 Other FRU 0x32

TX Fault SFP04 Other FRU 0x33

TX Fault SFP05 Other FRU 0x34

TX Fault SFP06 Other FRU 0x35

TX Fault SFP07 Other FRU 0x36

TX Fault SFP08 Other FRU 0x37

TX Fault SFP09 Other FRU 0x38

TX Fault SFP10 Other FRU 0x39

TX Fault SFP11 Other FRU 0x3A

TX Fault SFP12 Other FRU 0x3B

Table 4-1 IPMI Sensors Overview (continued)

Sensor Name Sensor Type Sensor Number

Contents

Main Trademarks Notice Limited and Restricted Rights Legend Contact Address Contents Page List of Tables Page List of Figures Page About this Manual Overview of Contents Abbreviations Conventions The following table describes the conventions used throughout this manual. Summary of Changes This manual has been revised and replaces all prior editions. Page Safety Notes Electrical Interference Safety Notes Operation Installation Safety Notes SFP/SFP+ Modules Environment Sicherheitshinweise EMV Operation Installation SFP/SFP+ Modules Umweltschutz Chapter 1 Introduction 1.1 Features Page Introduction 1.2 Standard Compliances For Declaration of Conformity refer, RTM Declaration of Conformity.. This RTM-ATCA-F120-OPT meets the following standards. Table 1-1 Standard Compliances Page Chapter 2 Hardware Preparation and Installation 2.1 Overview 2.2 Unpacking and Inspecting the RTM 2.3 Environmental and Power Requirements 2.3.1 Environmental Requirements 2.3.2 Power Requirements The RTM has a typical power dissipation of 22W, and a maximum power dissipation of 30W. Table 2-1 Environmental Requirements 2.4 Installing and Removing the RTM 2.4.1 Installing the RTM Page Page Page Page 2.4.2 Removing the RTM Page 2.5 Installing and Removing SFP/ SFP+ Modules Page Page Page Page Page Controls, LEDs and Connectors 3.2 LEDs and Interface Connectors The following figure shows the face plate of the RTM. Figure 3-1 Face Plate 3.2.1 LEDs The RTM provides four LEDs at its face plate. Their meaning is described in the following table. 3.2.2 Interface Connectors The RTM provides access to the following interfaces at its face plate. Table 3-1 Face Plate LEDs Page Figure 3-2 Location of Ethernet Fabric Channel Uplink Interfaces Fabric Channel - 1 Gbit Ethernet uplink 3.2.2.1.1 10 GBit Fabric Interface Channel Uplinks 3.2.2.1.2 1 GBit Fabric Interface Uplinks 3.2.2.2 Base Channel Interface Connectors Base interface- 10 GBit Ethernet uplink Base interface - 10 GBit Ethernet uplink 3.2.2.2.1 10 GBit Base Interface Uplinks 3.2.2.2.2 1 GBit Base Interface Uplinks 3.2.2.3 SFP/SFP+ Module Hot Swap 3.2.2.4 Telecom Clocking Connectors CH3 CH2 Page Figure 3-5 Location of Serial Interface Connectors Serial Interface Connector Page Functional Description 4.2 Block Diagram The following figure shows the main functional blocks of the RTM. Figure 4-1 Block Diagram RTM Face Plate Zone 3 Connectors 4.3 Mezzanine Management Controller Table 4-1 IPMI Sensors Overview (continued) The following figure shows the location of the on-board temperature sensors. Table 4-1 IPMI Sensors Overview (continued) Page Page Page Appendix A A.1 Emerson Network Power - Embedded Computing Documents Page Index Page Page HOW TO REACH LITERATURE AND TECHNICAL SUPPORT: