Manuals / Brands / Computer Equipment / Network Hardware / Emerson / Computer Equipment / Network Hardware

Emerson RTM-ATCA-F120-OPT , 3.2.2.2 Base Channel Interface Connectors

1 68

Download 68 pages, 1.44 Mb

Controls, LEDs and Connectors

RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 47

3.2.2.1.2 1 GBit Fabric Interface Uplinks

The two cages for 1 GBit connections can be equipped with standard SFP connectors for

copper and optical connections.

The SFP modules can be installed/removed both while the RTM is powered and non-powered.

The presence and also the type of SFP modules is automatically detected.

When using copper SFP modules, the speed is determined through auto-negotiation per the

802.11 Ethernet specification. Optical modules do not support auto-negotiation.

The following table shows which switch MIB OID each cage corresponds to.

3.2.2.2 Base Channel Interface Connectors

The RTM provides access to the folllowing six Ethernet base channel uplink interfaces at its face

plate:

zTwo 10 Gigabit Ethernet uplink interfaces via SFP+ connectors

zFour 1 Gigabit Ethernet interfaces via SFP connectors

Table 3-3 Fabric Channel 1 GBit Uplink Connectors - Port - MIB OID Assignment

Face Plate Label MIB OID Ethernet Type

FIX GE1 <shelf>.<slot>.2.40 1 GBit

FIX GE2 <shelf>.<slot>.2.41 1 GBit

Contents

Main Trademarks Notice Limited and Restricted Rights Legend Contact Address Contents Page List of Tables Page List of Figures Page About this Manual Overview of Contents Abbreviations Conventions The following table describes the conventions used throughout this manual. Summary of Changes This manual has been revised and replaces all prior editions. Page Safety Notes Electrical Interference Safety Notes Operation Installation Safety Notes SFP/SFP+ Modules Environment Sicherheitshinweise EMV Operation Installation SFP/SFP+ Modules Umweltschutz Chapter 1 Introduction 1.1 Features Page Introduction 1.2 Standard Compliances For Declaration of Conformity refer, RTM Declaration of Conformity.. This RTM-ATCA-F120-OPT meets the following standards. Table 1-1 Standard Compliances Page Chapter 2 Hardware Preparation and Installation 2.1 Overview 2.2 Unpacking and Inspecting the RTM 2.3 Environmental and Power Requirements 2.3.1 Environmental Requirements 2.3.2 Power Requirements The RTM has a typical power dissipation of 22W, and a maximum power dissipation of 30W. Table 2-1 Environmental Requirements 2.4 Installing and Removing the RTM 2.4.1 Installing the RTM Page Page Page Page 2.4.2 Removing the RTM Page 2.5 Installing and Removing SFP/ SFP+ Modules Page Page Page Page Page Controls, LEDs and Connectors 3.2 LEDs and Interface Connectors The following figure shows the face plate of the RTM. Figure 3-1 Face Plate 3.2.1 LEDs The RTM provides four LEDs at its face plate. Their meaning is described in the following table. 3.2.2 Interface Connectors The RTM provides access to the following interfaces at its face plate. Table 3-1 Face Plate LEDs Page Figure 3-2 Location of Ethernet Fabric Channel Uplink Interfaces Fabric Channel - 1 Gbit Ethernet uplink 3.2.2.1.1 10 GBit Fabric Interface Channel Uplinks 3.2.2.1.2 1 GBit Fabric Interface Uplinks 3.2.2.2 Base Channel Interface Connectors Base interface- 10 GBit Ethernet uplink Base interface - 10 GBit Ethernet uplink 3.2.2.2.1 10 GBit Base Interface Uplinks 3.2.2.2.2 1 GBit Base Interface Uplinks 3.2.2.3 SFP/SFP+ Module Hot Swap 3.2.2.4 Telecom Clocking Connectors CH3 CH2 Page Figure 3-5 Location of Serial Interface Connectors Serial Interface Connector Page Functional Description 4.2 Block Diagram The following figure shows the main functional blocks of the RTM. Figure 4-1 Block Diagram RTM Face Plate Zone 3 Connectors 4.3 Mezzanine Management Controller Table 4-1 IPMI Sensors Overview (continued) The following figure shows the location of the on-board temperature sensors. Table 4-1 IPMI Sensors Overview (continued) Page Page Page Appendix A A.1 Emerson Network Power - Embedded Computing Documents Page Index Page Page HOW TO REACH LITERATURE AND TECHNICAL SUPPORT: