Manuals / Brands / Computer Equipment / Network Hardware / Emerson / Computer Equipment / Network Hardware

Emerson RTM-ATCA-F120-OPT 3.2.2.1.1 10 GBit Fabric Interface Channel Uplinks

1 68

Download 68 pages, 1.44 Mb

Controls, LEDs and Connectors

RTM-ATCA-F120-OPT Installation and Use (6806800G29C)

46

3.2.2.1.1 10 GBit Fabric Interface Channel Uplinks

The four cages for the 10 GBit uplinks can be equipped with standard optical SFP+ connectors

and support Ethernet connections in compliance with the IEEEE 802.3ak standard.

Alternatively, you may populate the SFP+ connectors with SFP connectors for copper and

optical Ethernet connections. In this case, only 1 GBit connections are supported.

During the qualification testing of the RTM, the following SFP+ models were used:

z10Gb/s 850nm Multimode Datacom SFP+ Transceiver (FTLX8571D3BCL). Orderable via

Emerson P/N: 5806802A01

zRoHS-6 Compliant 10Gb/s 10km Single Mode Datacom SFP+ Transceiver

(FTLX1471D3BCL). Orderable via Emerson P/N: 5806803A01

These modules passed all tests sucessfully without incidents. They are also listed in the

Emerson Network Power sales configurator. When using SFP+ modules, we recommend to use

these models.

The SFP/SFP+ modules can be installed/removed both while the RTM is powered and non-

powered. The presence and also the type of SFP/SFP+ modules is automatically detected.

When using 1 GBit copper SFP modules, the speed is determined through auto-negotiation per

the 802.11 Ethernet specification. Optical modules do not support auto-negotiation. The SFP

cable should be appropriately matched to the SFP module type per the manufacturer’s

recommendations.

The following table shows which switch MIB OID each cage corresponds to.

Table 3-2 Fabric Channel 10 GBit Uplink Connectors - Port - MIB OID Assignment

Face Plate Label MIB OID Ethernet Type

FIX XG1 <shelf>.<slot>.2.17 10 GBit

FIX XG2 <shelf>.<slot>.2.16 10 GBit

FIX XG3 <shelf>.<slot>.2.19 10 GBit

FIX XG4 <shelf>.<slot>.2.18 10 GBit

Contents

Main Trademarks Notice Limited and Restricted Rights Legend Contact Address Contents Page List of Tables Page List of Figures Page About this Manual Overview of Contents Abbreviations Conventions The following table describes the conventions used throughout this manual. Summary of Changes This manual has been revised and replaces all prior editions. Page Safety Notes Electrical Interference Safety Notes Operation Installation Safety Notes SFP/SFP+ Modules Environment Sicherheitshinweise EMV Operation Installation SFP/SFP+ Modules Umweltschutz Chapter 1 Introduction 1.1 Features Page Introduction 1.2 Standard Compliances For Declaration of Conformity refer, RTM Declaration of Conformity.. This RTM-ATCA-F120-OPT meets the following standards. Table 1-1 Standard Compliances Page Chapter 2 Hardware Preparation and Installation 2.1 Overview 2.2 Unpacking and Inspecting the RTM 2.3 Environmental and Power Requirements 2.3.1 Environmental Requirements 2.3.2 Power Requirements The RTM has a typical power dissipation of 22W, and a maximum power dissipation of 30W. Table 2-1 Environmental Requirements 2.4 Installing and Removing the RTM 2.4.1 Installing the RTM Page Page Page Page 2.4.2 Removing the RTM Page 2.5 Installing and Removing SFP/ SFP+ Modules Page Page Page Page Page Controls, LEDs and Connectors 3.2 LEDs and Interface Connectors The following figure shows the face plate of the RTM. Figure 3-1 Face Plate 3.2.1 LEDs The RTM provides four LEDs at its face plate. Their meaning is described in the following table. 3.2.2 Interface Connectors The RTM provides access to the following interfaces at its face plate. Table 3-1 Face Plate LEDs Page Figure 3-2 Location of Ethernet Fabric Channel Uplink Interfaces Fabric Channel - 1 Gbit Ethernet uplink 3.2.2.1.1 10 GBit Fabric Interface Channel Uplinks 3.2.2.1.2 1 GBit Fabric Interface Uplinks 3.2.2.2 Base Channel Interface Connectors Base interface- 10 GBit Ethernet uplink Base interface - 10 GBit Ethernet uplink 3.2.2.2.1 10 GBit Base Interface Uplinks 3.2.2.2.2 1 GBit Base Interface Uplinks 3.2.2.3 SFP/SFP+ Module Hot Swap 3.2.2.4 Telecom Clocking Connectors CH3 CH2 Page Figure 3-5 Location of Serial Interface Connectors Serial Interface Connector Page Functional Description 4.2 Block Diagram The following figure shows the main functional blocks of the RTM. Figure 4-1 Block Diagram RTM Face Plate Zone 3 Connectors 4.3 Mezzanine Management Controller Table 4-1 IPMI Sensors Overview (continued) The following figure shows the location of the on-board temperature sensors. Table 4-1 IPMI Sensors Overview (continued) Page Page Page Appendix A A.1 Emerson Network Power - Embedded Computing Documents Page Index Page Page HOW TO REACH LITERATURE AND TECHNICAL SUPPORT: